pfSense 2.5 to pfSense 2.5 IPsec tunnel fails to connect
-
@jimp Thank you for compiling this convenient list of patches! Can I apply them to pfSense Plus 21.02 devices, or are they only for pfSense CE 2.5? I'm trying to make a basic IPsec tunnel between an SG-1100 and a homebuilt box, and cannot get it to work with those respective software versions. Forgive the question, as I have never tried using patches before. Also, do I need to revert the patches when the next upgrade becomes available, or is it safe to apply the upgrade on top of them? Thank you again!
-
Just a question, why is this not in an official fix or release yet? I have 3 firewalls spread out between my parents, my friends house and my own running the community edition. I don't understand why this hasn't been fixed yet. My ipsec tunnels are down even after a fresh install. I'm just confused why it is taking so long for this to become a "fix".
-
Making a new release takes time, effort, and testing. There are still numerous things we're actively investigating.
-
After upgraded to version 21.02-RELEASE-p1, my Netgate XG-7100 kept getting disconnected to a remote Cisco RV042 (even though it showed as connected). The IPsec tunnel had been working smoothly for a year without any hiccup now decided to act up. There is no pattern when it would stop the connection, most of the time just within couple minutes. I applied the 7 patches as advised about but still no luck. My tunnel is using IKEv1, AES_CBC (128), HMAC_SHA1_96, PRF_HMAC_SHA1, MODP_768. I am under the pressure to get it back on track. Please help! Thank you.
-
I finally got my IPsec tunnel to work without interruption on my Netgate XG-7100 by turning of the Hardware Crypto. I believe it is a work around solution since the Hardware Crypto has to be off.
-
@beejee said in pfSense 2.5 to pfSense 2.5 IPsec tunnel fails to connect:
I finally got my IPsec tunnel to work without interruption on my Netgate XG-7100 by turning of the Hardware Crypto. I believe it is a work around solution since the Hardware Crypto has to be off.
Which hardware crypto option did you have enabled on there? If it was AES-NI, that sounds similar to an issue we're already tracking. If it's not, it could be a different problem. On the XG-7100 you can switch from AES-NI to QAT which should be equal to or faster in performance and potentially more stable as the issues we're aware of only affect AES-NI at the moment.
-
@jimp said in pfSense 2.5 to pfSense 2.5 IPsec tunnel fails to connect:
Which hardware crypto option did you have enabled on there?
You were right. It was "AES-NI and BSD Cryto Device (aesni,cryptodev)" option. I believe it would be the best option for my appliance overall.
I will try the "QAT" as your suggested sometime tonight. Thank you!
-
@jimp said in pfSense 2.5 to pfSense 2.5 IPsec tunnel fails to connect:
On the XG-7100 you can switch from AES-NI to QAT which should be equal to or faster in performance and potentially more stable
Yes my XG-7100 IPsec tunnel is working smoothly with "Intel QuickAssist (QAT)" on. My CPU Type is "Intel(R) Atom(TM) CPU C3558 @ 2.20GHz". I actually don't know where to check if my IPsec tunnel is really using the QAT since I didn't see it is listed anywhere in the Dashboard. The Dashboard mentioned that "AES-NI CPU Crypto: Yes (inactive)" instead.
-
The next update will show QAT on the dashboard properly, but for now you can check:
- That the module is loaded:
: kldstat | grep qat 5 1 0xffffffff84322000 146e0 qat.ko 6 1 0xffffffff84337000 9f521 qat_c3xxxfw.ko - That the device is consuming interrupts (will increase as traffic is encrypted/decrypted through IPsec):
: vmstat -i | egrep 'total|qat' interrupt total rate irq300: qat0 489041 0
- That the module is loaded:
-
@jimp Awesome! I think my IPsec is really utilizing the QAT. Thank you so much!
I downloaded a large file through the tunnel and checked the stat::kldstat | grep qat 3 1 0xffffffff83f22000 146e0 qat.ko 4 1 0xffffffff83f37000 9f521 qat_c3xxxfw.ko :vmstat -i | egrep 'total|qat' interrupt total rate irq293: qat0 43576 1 irq294: qat0 27168 1 irq295: qat0 7909 0 irq296: qat0 18777 0 :vmstat -i | egrep 'total|qat' interrupt total rate irq293: qat0 396393 9 irq294: qat0 39664 1 irq295: qat0 19005 0 irq296: qat0 47598 1 -
@jimp Thanks I had problem with tunnel to a Cisco router where I could ping but then sending any traffic through would kill the tunnel. Switching my 5100 to QAT seems to have fixed this issue.
I have another tunnel between the SG-5100 and an older SG-2220.. enabling QAT on the 2200 is slower than using AES-NI - iperf3 test are 220Mbps with AES-NI and only around 100Mbps on QAT when I enable it on the SG-2220.
-
@jimp Guessing the Dashboard display for QAT or other crypto modules didn't make it to 21.02.2 - at least my XG-7100's still show 'AES-NI CPU Crypto: Yes (inactive) - no mention of QAT anywhere that I can find on a Dashboard widget etc.
-
@danjeman said in pfSense 2.5 to pfSense 2.5 IPsec tunnel fails to connect:
@jimp Guessing the Dashboard display for QAT or other crypto modules didn't make it to 21.02.2 - at least my XG-7100's still show 'AES-NI CPU Crypto: Yes (inactive) - no mention of QAT anywhere that I can find on a Dashboard widget etc.
It's there on 21.05 snapshots, didn't make it into 21.02.2.
