Can't assign NIC [Aquantia Corp. AQC107]

stephenw10 · Mar 31, 2021, 12:06 PM

No the pkg reply was for @daplumber. He enabled the full FreeBSD package repo rather than installing a single pkg dircetkly. And that's dangerous.
https://docs.netgate.com/pfsense/en/latest/recipes/freebsd-pkg-repo.html

I have no way to test any version of this driver beyond loading the kernel module that checks it's compatible with the kernel.

Steve

l9396 · Mar 31, 2021, 12:22 PM

@stephenw10 So there is no nothing dangerous in command "pkg install aquantia-atlantic-kmod"?

stephenw10 · Mar 31, 2021, 12:45 PM

That will only work if the package exists in the configured pkg repo and it's not in the pfSense repo. If that does work you have enabled the full FreeBSD repo and that is dangerous.

You should use "pkg add <full path to package>" and not enable the FreeBSD repo.

Steve

l9396 · Mar 31, 2021, 12:46 PM

@stephenw10 Thank you. I will disable it.

daplumber · Mar 31, 2021, 3:24 PM

@stephenw10 I temporarily enabled the FreeBSD repo only long enough to check for dependencies and install the kmod pkg. I then disabled it again.

I think I understand the warning and risks and DEFINITELY do not want to leave it enabled.

daplumber · Mar 31, 2021, 6:45 PM

@stephenw10

So I did the install as requested and :

[2.5.0-RELEASE][root@mypfsense.lan]/boot/modules: pkg add http://pkg.freebsd.org/FreeBSD:12:amd64/quarterly/All/aquantia-atlantic-kmod-0.0.5_1.txz
Fetching aquantia-atlantic-kmod-0.0.5_1.txz: 100%   22 KiB  22.7kB/s    00:01    
Installing aquantia-atlantic-kmod-0.0.5_1...
Extracting aquantia-atlantic-kmod-0.0.5_1: 100%
[2.5.0-RELEASE][root@mypfsense.lan]/boot/modules: ls -l if*
-r-xr-xr-x  1 root  wheel    95120 Feb 26 17:44 if_atlantic.ko
-r-xr-xr-x  1 root  wheel  1168400 Feb  5 17:02 if_re.ko
[2.5.0-RELEASE][root@mypfsense.lan]/boot/modules: kldload if_atlantic.ko 
kldload: if_atlantic.ko will be loaded from /boot/kernel, not the current directory

# kernel P A N I C ensues

Card hardware is installed and copacetic as far as I can tell from pciconf -l :

none0@pci0:2:0:0:	class=0x020000 card=0x00011d6a chip=0xd1071d6a rev=0x02 hdr=0x00
    vendor     = 'Aquantia Corp.'
    device     = 'AQC107 NBase-T/IEEE 802.3bz Ethernet Controller [AQtion]'
    class      = network
    subclass   = ethernet
    bar   [10] = type Memory, range 64, base 0xfd6f0000, size 65536, enabled
    bar   [18] = type Memory, range 64, base 0xfd6ef000, size 4096, enabled
    bar   [20] = type Memory, range 64, base 0xfd000000, size 4194304, enabled
    cap 10[40] = PCI-Express 2 endpoint max data 128(512) FLR NS
                 max read 512
                 link x4(x4) speed 5.0(8.0) ASPM disabled(L0s/L1)
    cap 01[80] = powerspec 3  supports D0 D1 D2 D3  current D0
    cap 11[90] = MSI-X supports 32 messages
                 Table in map 0x18[0x0], PBA in map 0x18[0x200]
    cap 05[a0] = MSI supports 32 messages, 64 bit 
    cap 03[c0] = VPD
    ecap 0001[100] = AER 2 0 fatal 0 non-fatal 1 corrected
    ecap 000b[150] = Vendor 1 ID 1
    ecap 0019[180] = PCIe Sec 1 lane errors 0
    VPD ident  = 'AQtion'
    VPD ro PN  = 'AquantiaPartNumber'
    VPD ro EC  = 'AquantiaEngineeringChangeLevel'
    VPD ro FG  = 'AquantiaFabricGeography'
    VPD ro LC  = 'AquantiaLocation'
    VPD ro MN  = 'AquantiaManufacturingId'
    VPD ro PG  = 'AquantiaPciGeography'
    VPD ro SN  = 'AquantiaSerialNumber'
    VPD ro V0  = 'AquantiaVendorSpecificReadOnlyItem0'
    VPD ro V1  = 'AquantiaVendorSpecificReadOnlyItem1'
    VPD rw YA  = 'AquantiaAssetTagIdentifier'
    VPD rw V0  = 'AquantiaVendorSpecificWritableItem0'
    VPD rw V1  = 'AquantiaVendorSpecificWritableItem1'
    VPD rw Y0  = 'AquantiaSystemSpecificWritableItem0'
    VPD rw Y1  = 'AquantiaSystemSpecificWritableItem1'

I feel like I'm missing something simple and/or stupid here...

stephenw10 · Apr 1, 2021, 12:44 PM

@daplumber said in Can't assign NIC [Aquantia Corp. AQC107]:

kldload: if_atlantic.ko will be loaded from /boot/kernel, not the current directory

So what module did it actually load? You have a different module in /boot/kernel?

If you remove the card does the module load without throwing a panic?

Steve

Rico · Apr 2, 2021, 11:39 AM

Here you go: if_atlantic0.0.5_freebsd12.2.zip

-Rico

daplumber · Apr 4, 2021, 10:42 AM

@rico THANK YOU! OK, so ill-advised aside, this build of the driver works on 2.5.0-RELEASE (amd64) on FreeBSD 12.2-STABLE:

[2.5.0-RELEASE][root@mypfsense]/root: kldstat
Id Refs Address                Size Name
 1   28 0xffffffff80200000  3aea538 kernel
 2    1 0xffffffff83ceb000     ef18 aesni.ko
 3    1 0xffffffff83cfa000   3bb7f0 zfs.ko
 4    2 0xffffffff840b6000     a448 opensolaris.ko
 5    1 0xffffffff840c2000    19e88 if_atlantic.ko
 6    1 0xffffffff84311000     1000 cpuctl.ko
 7    1 0xffffffff84312000     2698 intpm.ko
 8    1 0xffffffff84315000      b40 smbus.ko
 9    1 0xffffffff84316000     1490 amdtemp.ko
10    1 0xffffffff84318000      818 amdsmn.ko
[2.5.0-RELEASE][root@mypfsense]/root: uname -a
FreeBSD my pfsense.mydomain 12.2-STABLE FreeBSD 12.2-STABLE d48fb226319(devel-12) pfSense  amd64

So, what, pray tell, did you do different yo build this that's different from the official repo?

It does, however take it's own sweet time booting the card, is this normal?

It's pretty chatty too, here's the dmesg output:

---<<BOOT>>---
Copyright (c) 1992-2020 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 12.2-STABLE d48fb226319(devel-12) pfSense amd64
FreeBSD clang version 10.0.1 (git@github.com:llvm/llvm-project.git llvmorg-10.0.1-0-gef32c611aa2)
CPU: AMD FX(tm)-8320 Eight-Core Processor            (3492.36-MHz K8-class CPU)
  Origin="AuthenticAMD"  Id=0x600f20  Family=0x15  Model=0x2  Stepping=0
  Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
  Features2=0x3e98320b<SSE3,PCLMULQDQ,MON,SSSE3,FMA,CX16,SSE4.1,SSE4.2,POPCNT,AESNI,XSAVE,OSXSAVE,AVX,F16C>
  AMD Features=0x2e500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM>
  AMD Features2=0x1ebbfff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,XOP,SKINIT,WDT,LWP,FMA4,TCE,NodeId,TBM,Topology,PCXC,PNXC>
  Structured Extended Features=0x8<BMI1>
  SVM: NP,NRIP,VClean,AFlush,DAssist,NAsids=65536
  TSC: P-state invariant, performance statistics
real memory  = 8589934592 (8192 MB)
avail memory = 8209915904 (7829 MB)
Event timer "LAPIC" quality 600
ACPI APIC Table: <051118 APIC1911>
FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs
FreeBSD/SMP: 1 package(s) x 8 core(s)
random: unblocking device.
Firmware Warning (ACPI): Optional FADT field Pm2ControlBlock has valid Length but zero Address: 0x0000000000000000/0x1 (20200430/tbfadt-796)
ioapic0: MADT APIC ID 24 != hw id 0
ioapic0 <Version 2.1> irqs 0-23 on motherboard
Launching APs: 1 4 6 3 2 7 5
Timecounter "TSC-low" frequency 1746181517 Hz quality 1000
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xffffffff8073dc40, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffffffff8073dcf0, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffffffff8073dda0, 0) error 1
iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_bss_fw, 0xffffffff80765630, 0) error 1
iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_ibss_fw, 0xffffffff807656e0, 0) error 1
iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_monitor_fw, 0xffffffff80765790, 0) error 1
wlan: mac acl policy registered
random: entropy device external interface
kbd1 at kbdmux0
[ath_hal] loaded
000.000059 [4336] netmap_init               netmap: loaded module
mlx5en: Mellanox Ethernet driver 3.5.2 (September 2019)
nexus0
cryptosoft0: <software crypto> on motherboard
padlock0: No ACE support.
aesni0: <AES-CBC,AES-CCM,AES-GCM,AES-ICM,AES-XTS> on motherboard
acpi0: <051118 RSDT1911> on motherboard
acpi0: Power Button (fixed)
cpu0: <ACPI CPU> on acpi0
attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
atrtc0: registered as a time-of-day clock, resolution 1.000000s
Event timer "RTC" frequency 32768 Hz quality 0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xc000-0xc0ff mem 0xfa000000-0xfbffffff,0xfcff0000-0xfcffffff,0xfce00000-0xfcefffff irq 18 at device 5.0 on pci1
vgapci0: Boot video device
hdac0: <ATI RS780 HDA Controller> mem 0xfcfe8000-0xfcfebfff irq 19 at device 5.1 on pci1
pcib2: <ACPI PCI-PCI bridge> irq 18 at device 2.0 on pci0
pci2: <ACPI PCI bus> on pcib2
aq0: <Aquantia AQtion 10Gbit Network Adapter> mem 0xfd6f0000-0xfd6fffff,0xfd6ef000-0xfd6effff,0xfd000000-0xfd3fffff irq 18 at device 0.0 on pci2
atlantic: FLB> F/W successfully loaded from flash.
atlantic: MAC F/W version is 3.1.86
atlantic: FLB> F/W successfully loaded from flash.
aq0: Using 1024 TX descriptors and 1024 RX descriptors
aq0: Using 8 RX queues 8 TX queues
aq0: Using MSI-X interrupts with 9 vectors
aq0: Assign IRQ 0 to rx ring 0
aq0: Assign IRQ 1 to rx ring 1
aq0: Assign IRQ 2 to rx ring 2
aq0: Assign IRQ 3 to rx ring 3
aq0: Assign IRQ 4 to rx ring 4
aq0: Assign IRQ 5 to rx ring 5
aq0: Assign IRQ 6 to rx ring 6
aq0: Assign IRQ 7 to rx ring 7
aq0: Assign IRQ 0 to tx ring 0
aq0: Assign IRQ 1 to tx ring 1
aq0: Assign IRQ 2 to tx ring 2
aq0: Assign IRQ 3 to tx ring 3
aq0: Assign IRQ 4 to tx ring 4
aq0: Assign IRQ 5 to tx ring 5
aq0: Assign IRQ 6 to tx ring 6
aq0: Assign IRQ 7 to tx ring 7
aq0: Assign IRQ 8 to admin proc 
aq0: Ethernet address: 00:1b:22:32:24:7a
aq0: netmap queues/slots: TX 8/1024, RX 8/1024
pcib3: <ACPI PCI-PCI bridge> irq 17 at device 5.0 on pci0
pci3: <ACPI PCI bus> on pcib3
re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0xd800-0xd8ff mem 0xfd7ff000-0xfd7fffff,0xfd7f8000-0xfd7fbfff irq 17 at device 0.0 on pci3
re0: Using 1 MSI-X message
re0: Chip rev. 0x54000000
re0: MAC rev. 0x00100000
miibus0: <MII bus> on re0
rgephy0: <RTL8251/8153 1000BASE-T media interface> PHY 1 on miibus0
rgephy0:  none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
re0: Using defaults for TSO: 65518/35/2048
re0: Ethernet address: a8:a1:59:5e:1b:ec
re0: netmap queues/slots: TX 1/256, RX 1/256
pcib4: <ACPI PCI-PCI bridge> irq 18 at device 6.0 on pci0
pci4: <ACPI PCI bus> on pcib4
igb0: <Intel(R) PRO/1000 PCI-Express Network Driver> port 0xe800-0xe81f mem 0xfebe0000-0xfebfffff,0xfe400000-0xfe7fffff,0xfebdc000-0xfebdffff irq 18 at device 0.0 on pci4
igb0: Using 1024 TX descriptors and 1024 RX descriptors
igb0: Using 8 RX queues 8 TX queues
igb0: Using MSI-X interrupts with 9 vectors
igb0: Ethernet address: 80:61:5f:08:2b:76
igb0: netmap queues/slots: TX 8/1024, RX 8/1024
igb1: <Intel(R) PRO/1000 PCI-Express Network Driver> port 0xe400-0xe41f mem 0xfeba0000-0xfebbffff,0xfdc00000-0xfdffffff,0xfebd8000-0xfebdbfff irq 19 at device 0.1 on pci4
igb1: Using 1024 TX descriptors and 1024 RX descriptors
igb1: Using 8 RX queues 8 TX queues
igb1: Using MSI-X interrupts with 9 vectors
igb1: Ethernet address: 80:61:5f:08:2b:77
igb1: netmap queues/slots: TX 8/1024, RX 8/1024
ahci0: <AMD SB7x0/SB8x0/SB9x0 AHCI SATA controller> port 0xb000-0xb007,0xa000-0xa003,0x9000-0x9007,0x8000-0x8003,0x7000-0x700f mem 0xfcdffc00-0xfcdfffff irq 22 at device 17.0 on pci0
ahci0: AHCI v1.10 with 4 3Gbps ports, Port Multiplier supported
ahci0: quirks=0x22000<ATI_PMP_BUG,1MSI>
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
ahcich2: <AHCI channel> at channel 2 on ahci0
ahcich3: <AHCI channel> at channel 3 on ahci0
ohci0: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xfcdfe000-0xfcdfefff irq 16 at device 18.0 on pci0
usbus0 on ohci0
usbus0: 12Mbps Full Speed USB v1.0
ohci1: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xfcdfd000-0xfcdfdfff irq 16 at device 18.1 on pci0
usbus1 on ohci1
usbus1: 12Mbps Full Speed USB v1.0
ehci0: <AMD SB7x0/SB8x0/SB9x0 USB 2.0 controller> mem 0xfcdff800-0xfcdff8ff irq 17 at device 18.2 on pci0
usbus2: EHCI version 1.0
usbus2 on ehci0
usbus2: 480Mbps High Speed USB v2.0
ohci2: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xfcdfc000-0xfcdfcfff irq 18 at device 19.0 on pci0
usbus3 on ohci2
usbus3: 12Mbps Full Speed USB v1.0
ohci3: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xfcdfb000-0xfcdfbfff irq 18 at device 19.1 on pci0
usbus4 on ohci3
usbus4: 12Mbps Full Speed USB v1.0
ehci1: <AMD SB7x0/SB8x0/SB9x0 USB 2.0 controller> mem 0xfcdff400-0xfcdff4ff irq 19 at device 19.2 on pci0
usbus5: EHCI version 1.0
usbus5 on ehci1
usbus5: 480Mbps High Speed USB v2.0
atapci0: <ATI IXP700/800 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 20.1 on pci0
ata0: <ATA channel> at channel 0 on atapci0
ata1: <ATA channel> at channel 1 on atapci0
hdac1: <ATI SB600 HDA Controller> mem 0xfcdf4000-0xfcdf7fff irq 16 at device 20.2 on pci0
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib5: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pci5: <ACPI PCI bus> on pcib5
ohci4: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xfcdfa000-0xfcdfafff irq 18 at device 20.5 on pci0
usbus6 on ohci4
usbus6: 12Mbps Full Speed USB v1.0
acpi_button0: <Power Button> on acpi0
orm0: <ISA Option ROMs> at iomem 0xcf000-0xd0fff,0xd1000-0xd1fff,0xd2000-0xd2fff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff pnpid PNP0900 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
hwpstate0: <Cool`n'Quiet 2.0> on cpu0
ZFS filesystem version: 5
ZFS storage pool version: features support (5000)
Timecounters tick every 1.000 msec
hdacc0: <ATI RS690/780 HDA CODEC> at cad 0 on hdac0
hdaa0: <ATI RS690/780 Audio Function Group> at nid 1 on hdacc0
pcm0: <ATI RS690/780 (HDMI)> at nid 3 on hdaa0
hdacc1: <Realtek ALC887 HDA CODEC> at cad 0 on hdac1
hdaa1: <Realtek ALC887 Audio Function Group> at nid 1 on hdacc1
pcm1: <Realtek ALC887 (Rear Analog)> at nid 20 and 24,26 on hdaa1
pcm2: <Realtek ALC887 (Front Analog)> at nid 27 and 25 on hdaa1
ugen0.1: <ATI OHCI root HUB> at usbus0
ugen4.1: <ATI OHCI root HUB> at usbus4
ugen6.1: <ATI OHCI root HUB> at usbus6
ugen1.1: <ATI OHCI root HUB> at usbus1
Trying to mount root from zfs:zroot/ROOT/default []...
Root mount waiting for: CAM usbus0 usbus1 usbus2 usbus3 usbus4 usbus5 usbus6
uhub0: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
uhub1: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
ugen3.1: <ATI OHCI root HUB> at usbus3
uhub2: ugen2.1: <ATI EHCI root HUB> at usbus2
<ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
uhub3: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
uhub5: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
uhub4: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen5.1: <ATI EHCI root HUB> at usbus5
uhub6: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus5
uhub1: 2 ports with 2 removable, self powered
uhub0: 3 ports with 3 removable, self powered
uhub5: 3 ports with 3 removable, self powered
uhub3: 3 ports with 3 removable, self powered
uhub2: 3 ports with 3 removable, self powered
Root mount waiting for: CAM usbus2 usbus5
Root mount waiting for: CAM usbus2 usbus5
uhub4: 6 ports with 6 removable, self powered
uhub6: 6 ports with 6 removable, self powered
Root mount waiting for: CAM
ugen0.2: <CPS ABMT1000> at usbus0
Root mount waiting for: CAM
ugen0.3: <SEM USB Keyboard> at usbus0
ukbd0 on uhub0
ukbd0: <SEM USB Keyboard, class 0/0, rev 1.10/1.10, addr 3> on usbus0
kbd2 at ukbd0
uhid0 on uhub0
uhid0: <SEM USB Keyboard, class 0/0, rev 1.10/1.10, addr 3> on usbus0
Root mount waiting for: CAM
Root mount waiting for: CAM
Root mount waiting for: CAM
Root mount waiting for: CAM
Root mount waiting for: CAM
ada0 at ahcich0 bus 0 scbus0 target 0 lun 0
ada0: <OCZ INTREPID 3700 1.5.1.0A> ACS-2 ATA SATA 3.x device
ada0: Serial Number A22IO061546000445
ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 915715MB (1875385008 512 byte sectors)
GEOM_ELI: Device ada0p3.eli created.
GEOM_ELI: Encryption: AES-XTS 256
GEOM_ELI:     Crypto: hardware
Dual Console: Video Primary, Serial Secondary
CPU: AMD FX(tm)-8320 Eight-Core Processor            (3492.36-MHz K8-class CPU)
  Origin="AuthenticAMD"  Id=0x600f20  Family=0x15  Model=0x2  Stepping=0
  Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
  Features2=0x3e98320b<SSE3,PCLMULQDQ,MON,SSSE3,FMA,CX16,SSE4.1,SSE4.2,POPCNT,AESNI,XSAVE,OSXSAVE,AVX,F16C>
  AMD Features=0x2e500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM>
  AMD Features2=0x1ebbfff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,XOP,SKINIT,WDT,LWP,FMA4,TCE,NodeId,TBM,Topology,PCXC,PNXC>
  Structured Extended Features=0x8<BMI1>
  SVM: NP,NRIP,VClean,AFlush,DAssist,NAsids=65536
  TSC: P-state invariant, performance statistics
intsmb0: <AMD SB600/7xx/8xx/9xx SMBus Controller> at device 20.0 on pci0
intsmb0: intr SMI enabled revision 0
intsmb0: using polling mode when configured interrupt is SMI
smbus0: <System Management Bus> on intsmb0
amdtemp0: <AMD CPU On-Die Thermal Sensors> on hostb4
lo0: link state changed to UP
atlantic: FLB> F/W successfully loaded from flash.
aq0: ring 0: __PAGESIZE=4096 MCLBYTES=2048 hw->max_frame_size=2048
aq0: ring 1: __PAGESIZE=4096 MCLBYTES=2048 hw->max_frame_size=2048
aq0: ring 2: __PAGESIZE=4096 MCLBYTES=2048 hw->max_frame_size=2048
aq0: ring 3: __PAGESIZE=4096 MCLBYTES=2048 hw->max_frame_size=2048
aq0: ring 4: __PAGESIZE=4096 MCLBYTES=2048 hw->max_frame_size=2048
aq0: ring 5: __PAGESIZE=4096 MCLBYTES=2048 hw->max_frame_size=2048
aq0: ring 6: __PAGESIZE=4096 MCLBYTES=2048 hw->max_frame_size=2048
aq0: ring 7: __PAGESIZE=4096 MCLBYTES=2048 hw->max_frame_size=2048
atlantic: set 1 mc address 33:33:ff:32:24:7a
atlantic: set 1 mc address 33:33:00:00:00:01
atlantic: set 2 mc address 33:33:ff:32:24:7a
atlantic: set 1 mc address 33:33:ff:c2:9f:15
atlantic: set 2 mc address 33:33:00:00:00:01
atlantic: set 3 mc address 33:33:ff:32:24:7a
atlantic: set 1 mc address 33:33:c2:9f:15:75
atlantic: set 2 mc address 33:33:ff:c2:9f:15
atlantic: set 3 mc address 33:33:00:00:00:01
atlantic: set 4 mc address 33:33:ff:32:24:7a
atlantic: set 1 mc address 33:33:c2:9f:15:75
atlantic: set 2 mc address 33:33:ff:c2:9f:15
atlantic: set 3 mc address 33:33:00:00:00:01
atlantic: set 4 mc address 33:33:ff:32:24:7a
aq0: atlantic: link UP: speed=2500
aq0: link state changed to UP
atlantic: set 1 mc address 01:00:5e:00:00:01
atlantic: set 2 mc address 33:33:c2:9f:15:75
atlantic: set 3 mc address 33:33:ff:c2:9f:15
atlantic: set 4 mc address 33:33:00:00:00:01
atlantic: set 5 mc address 33:33:ff:32:24:7a
atlantic: set 1 mc address 33:33:c2:9f:15:75
atlantic: set 2 mc address 33:33:ff:c2:9f:15
atlantic: set 3 mc address 33:33:00:00:00:01
atlantic: set 4 mc address 33:33:ff:32:24:7a
atlantic: set 1 mc address 01:00:5e:00:00:01
atlantic: set 2 mc address 33:33:c2:9f:15:75
atlantic: set 3 mc address 33:33:ff:c2:9f:15
atlantic: set 4 mc address 33:33:00:00:00:01
atlantic: set 5 mc address 33:33:ff:32:24:7a
atlantic: set 1 mc address 33:33:c2:9f:15:75
atlantic: set 2 mc address 33:33:ff:c2:9f:15
atlantic: set 3 mc address 33:33:00:00:00:01
atlantic: set 4 mc address 33:33:ff:32:24:7a
igb1: link state changed to UP
tun1: changing name to 'ovpns1'
tun2: changing name to 'ovpns2'
ovpns1: link state changed to UP
ovpns2: link state changed to UP
pflog0: promiscuous mode enabled
atlantic: set 1 mc address 33:33:ff:3b:d4:bc
atlantic: set 2 mc address 33:33:c2:9f:15:75
atlantic: set 3 mc address 33:33:ff:c2:9f:15
atlantic: set 4 mc address 33:33:00:00:00:01
atlantic: set 5 mc address 33:33:ff:32:24:7a
pid 98504 (unbound), jid 0, uid 59: exited on signal 11
re0: link state changed to DOWN
igb1: promiscuous mode enabled
atlantic: FLB> F/W successfully loaded from flash.
aq0: ring 0: __PAGESIZE=4096 MCLBYTES=2048 hw->max_frame_size=2048
aq0: ring 1: __PAGESIZE=4096 MCLBYTES=2048 hw->max_frame_size=2048
aq0: ring 2: __PAGESIZE=4096 MCLBYTES=2048 hw->max_frame_size=2048
aq0: ring 3: __PAGESIZE=4096 MCLBYTES=2048 hw->max_frame_size=2048
aq0: ring 4: __PAGESIZE=4096 MCLBYTES=2048 hw->max_frame_size=2048
aq0: ring 5: __PAGESIZE=4096 MCLBYTES=2048 hw->max_frame_size=2048
aq0: ring 6: __PAGESIZE=4096 MCLBYTES=2048 hw->max_frame_size=2048
aq0: ring 7: __PAGESIZE=4096 MCLBYTES=2048 hw->max_frame_size=2048
aq0: promiscuous mode enabled
aq0: promiscuous mode disabled
aq0: atlantic: link UP: speed=2500
arp: 192.168.123.184 moved from 34:15:9e:26:bf:96 to 00:26:bb:6b:12:a0 on igb1
pid 86753 (unbound), jid 0, uid 59: exited on signal 11
pid 91458 (unbound), jid 0, uid 59: exited on signal 11

ifconfig:

[2.5.0-RELEASE][root@mypfsense]/root: ifconfig aq0
aq0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
	description: WAN
	options=8100b8<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,VLAN_HWFILTER>
	ether XX:XX:XX:XX:24:7a
	inet6 fe80::XXX:XXXX:XXXX:XXXX%aq0 prefixlen 64 scopeid 0x1
	inet6 2001:XXX:XXXX:XX:XXXX:XXXX:XXXX:XXXX prefixlen 128
	inet XXX.XXX.XXX.XXX netmask 0xfffffe00 broadcast 255.255.255.255
	inet 192.168.100.100 netmask 0xffffff00 broadcast 192.168.100.255
	media: Ethernet autoselect <full-duplex,rxpause,txpause> (2500Base-T <full-duplex,rxpause,txpause>)
	status: active
	nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>

As you can see it successfully negotiates a 2.5Gb connection to my CM as WAN, and even picks up the CM diagnostic IP. A quick Speedtest on the pfSense box itself confirms real world speeds above 1G. (Thank you Comcast!) Practically speaking until I upgrade the LAN link to 10G this is a bit pointless, but at least it's working now!

daplumber · Apr 8, 2021, 7:41 PM

@rico I think I spy a bug in the IPV6 link local address:

inet6 fe80::XXX:XXXX:XXXX:XXXX%aq0 prefixlen 64 scopeid 0x1

I'm pretty sure the "%aq0" shouldn't be part of the address? ;-)

Workaround: Check the "Only request an IPv6 prefix, do not request an IPv6 address" box on the WAN Interface panel. Obviously that means the pfSense box itself no longer has a WAN IPV6 address, but at least now the LAN side IPV6 systems will work.

stephenw10 · Apr 4, 2021, 11:34 AM

Compiled with debug options or something similar?

VAMike · Apr 8, 2021, 7:41 PM

@daplumber said in Can't assign NIC [Aquantia Corp. AQC107]:

@rico I think I spy a bug in the IPV6 link local address:
inet6 fe80::XXX:XXXX:XXXX:XXXX%aq0 prefixlen 64 scopeid 0x1
I'm pretty sure the "%aq0" shouldn't be part of the address? ;-)

That's completely normal syntax, indicating the scope of the address. See RFC4007.

daplumber · Apr 9, 2021, 2:47 AM

@vamike my bad. Forehead slap, forgot all about that.

Still no idea why IPv6 dhcp client is not picking up an address with the exact same configuration that worked with igb0...

Rico · May 9, 2022, 9:20 AM

As per request FreeBSD 12.3 (pfSense 22.01): if_atlantic0.0.5_freebsd12.3.zip

-Rico

donfox · May 9, 2022, 9:43 AM

tried the build on 22.01-RELEASE

[22.01-RELEASE][admin@metalcore.fox]/root: kldstat
Id Refs Address                Size Name
 1   13 0xffffffff80200000  3aefff8 kernel
 2    1 0xffffffff83cf0000    16ba0 if_atlantic.ko
 3    1 0xffffffff83d07000   11d288 if_re.ko
 4    1 0xffffffff860b5000     1000 cpuctl.ko
 5    1 0xffffffff860b6000     2150 acpi_wmi.ko

but there is no new interface :(

stephenw10 · May 9, 2022, 11:24 AM

What hardware are you trying to use it with?

donfox · May 9, 2022, 11:28 AM

@stephenw10

ASUS XG-C100C 10gbit

none5@pci0:1:0:0:       class=0x020000 card=0x88121043 chip=0x94c01d6a rev=0x03 hdr=0x00
    vendor     = 'Aquantia Corp.'
    class      = network
    subclass   = ethernet
    bar   [10] = type Memory, range 64, base 0xa1400000, size 524288, enabled
    bar   [18] = type Memory, range 64, base 0xa14a0000, size 4096, enabled
    bar   [20] = type Memory, range 64, base 0xa1000000, size 4194304, enabled

stephenw10 · May 9, 2022, 11:44 AM

94c0 is not a listed device ID in the driver:
https://github.com/Aquantia/aqtion-freebsd/blob/master/aq_main.c#L92

Not supported yet by the looks of it.

Steve

yorke · Jul 30, 2022, 6:46 PM

pfSense version 2.6.0

I have a Aquantia (AOM-AQS-107-B0C2-CX) Installed the drivers provided here
Everything seem to be working fine can get ip and connect, the only issue I am having
is that 5GBASE-T, 2.5GBASE-T aren't listed under the interface speed and duplex
and on the dashboard its listed as unknown full duplex

kldstat 19e28 if_atlantic.ko

ifconfig for the interface shows
media: Ethernet auto select (unknown <full-duplex)

tested under windows and 5GBASE-T, 2.5GBASE-T are listed

pciconf -i and shows the error listed below
link x1(x1) speed 2.5(2.5) ASPM disabled(L0s/L1)

stephenw10 · Aug 1, 2022, 8:18 PM

That pciconf error is probably unrelated.

Does it actually link at 2.5G? The other end reports that?