[solved] RA Subnets

Bob.Dig

@jegr I am trying this right now, never used an IP alias before. lets see if I succeed.

Bob.Dig

@jegr Instantly works, thanks Jens!

JKnott

@jegr said in [Bug] RA Subnets:

How about simply giving pfSense an appropriate ULA IP6 via an IP ALIAS as you want it to serve two different prefixes?

My complaint is the alias doesn't show up anywhere other than with the ifconfig command.

Bob.Dig

@jknott said in [solved] RA Subnets:

My complaint is the alias doesn't show up anywhere other than with the ifconfig command.

That is true, now I can see this myself.

JeGr

@jknott said in [solved] RA Subnets:

My complaint is the alias doesn't show up anywhere other than with the ifconfig command.

Perhaps I'm tired but I can't follow :) Care to elaborate?

Bob.Dig

@jegr said in [solved] RA Subnets:

Also your firewall rules will not work in "normal" ways anymore as "<lan> network" alias won't magically include the second prefix on that interface, only the one configured via Interface setup. So watch your rules, too!

Interestingly it worked anyway. I pinged the "lan" interface from the "voip" interface without a problem.

PS C:\Windows\system32> ping fd28:faaf:f468:1:192:168:1:1

Pinging fd28:faaf:f468:1:192:168:1:1 with 32 bytes of data:
Reply from fd28:faaf:f468:1:192:168:1:1: time<1ms
Reply from fd28:faaf:f468:1:192:168:1:1: time<1ms
Reply from fd28:faaf:f468:1:192:168:1:1: time<1ms
Reply from fd28:faaf:f468:1:192:168:1:1: time<1ms

Ping statistics for fd28:faaf:f468:1:192:168:1:1:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 0ms, Maximum = 0ms, Average = 0ms

"voip" was the interface in question all the time. Will have to try from another interface to "voip".

Bob.Dig

@bob-dig said in [solved] RA Subnets:

Will have to try from another interface to "voip".

Even this is working without any modifications @JeGr

Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),

Bob.Dig

So I think pfSense knows what "lan_voip net" is because of ifconfig:

hn4: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
        description: lan_voip
        options=48071b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,TSO4,TSO6,LRO,LINKSTATE,TXCSUM_IPV6>
        ether 00:15:5d:82:4e:3c
        inet6 fe80::215:5dff:fe82:4e3c%hn4 prefixlen 64 scopeid 0xa
        inet6 fe80::1:1%hn4 prefixlen 64 scopeid 0xa
        inet6 fd28:faaf:f468:98:192:168:98:1 prefixlen 64
        inet6 2003:da:a711:44f0:215:5dff:fe82:4e3c prefixlen 64
        inet 192.168.98.1 netmask 0xffffff00 broadcast 192.168.98.255
        media: Ethernet autoselect (10Gbase-T <full-duplex>)
        status: active
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>

JKnott

@jegr said in [solved] RA Subnets:

@jknott said in [solved] RA Subnets:

My complaint is the alias doesn't show up anywhere other than with the ifconfig command.

Perhaps I'm tired but I can't follow :) Care to elaborate?

Create an IP alias and see where it's listed. You won't see it in the web config. You have to go to a command prompt and run ifconfig to see that it's actually configured.

Bob.Dig

Some closing thoughts, I think with IPv6 it is normal to have more than one address per interface, so it would be better to have this option right in the interface-tab. Lets say I am giving input in IPv6 Configuration Type it should instantly allow for another IPv6 and so on.
Also what makes IPs virtual in the first place, some trickery? Again, shouldn't be needed for more IPv6-addresses.

JKnott

@bob-dig

I agree it should be easier to find. As for the name alias, that was even the case with IPv4, before there was IPv6. I assume it's because you have more than one address an interface can use, which is not typical. Also, with IPv6, you have not just mulitple addresses, you have multiple prefixes. Even if you don't have an alias, with SLAAC you can have up to 8 addresses, then there's link local too. By the time you've added a 2nd prefix, you're up to 17 addresses on a single interface.