Pfsense hardware for home
-
Yeah, reproducible here too.
The difference I pretty noticeable.But difficult thing to dissect. :)
-
However, as confusing as it is, I think we can reliably state that AES-128 (at over 567MB/s) and aes-256 (Over 442MB/s) will both perform well (by the benchmarks that I ran) regardless if the aes-ni box is checked in the GUI. I don't think any of us are using the APU2 boxes in environments where we are pushing more than 400MB/s encrypted traffic. And if they can do greater than 400MB/s encrypted then they can certainly do faster than that on pure NAT. While my iperf numbers are consistently low no matter what I try (gave up on it), speed tests show I have no problem cracking 200MB/s with Squid+SquidGuard+AV+Snort running and that shows a peak of 33% utilization in the pfSense GUI.
Can they to GB Line speed with just NAT? Probably. I can't really test it. We can safely say, however, that the APU2D4 can certainly do at least 500MB/s UTM which places it within arms reach of the SonicWall TZ400 for 2/3 less and no annual fees. Aside from expandability and convenience factors it's better than all Cisco ISA models and many Cisco ASA models. (Although I fear saying that since I'm sure some CCNA will find this thread and jump in to talk about how nothing can touch a Cisco, ever!)
Do I wish it could do full GB no matter what we throw at it? Absolutely! But since the whole kit is $200 I'm not sure there's room to complain. Does this need to be fixed/clarified? Certainly! Something needs to be addressed here but as long as we know the limitations, it's just something to work around for now. Any other thoughts?
-
However, as confusing as it is, I think we can reliably state that AES-128 (at over 567MB/s) and aes-256 (Over 442MB/s) will both perform well (by the benchmarks that I ran) regardless if the aes-ni box is checked in the GUI.
It depends I would think.
On a system under load where the load is taking CPU cycles it could be better to use the hardware crypto support (not loading module).400MB/s
200MB/sThink you mean Mbit/s…
Any other thoughts?
Saw a ticket last week about they will change something about the crypto module, maybe they try to address something, I don`t know.
-
However, as confusing as it is, I think we can reliably state that AES-128 (at over 567MB/s) and aes-256 (Over 442MB/s) will both perform well (by the benchmarks that I ran) regardless if the aes-ni box is checked in the GUI.
It depends I would think.
On a system under load where the load is taking CPU cycles it could be better to use the hardware crypto support (not loading module).400MB/s
200MB/sThink you mean Mbit/s…
Any other thoughts?
Saw a ticket last week about they will change something about the crypto module, maybe they try to address something, I don`t know.
1. Yes. My tests show anywhere from 99% loss to 4% gain when enabling the module in the GUI. It's definitely better to just leave it off. It is perplexing, though, how the APU2C lags behind the APU1D in some of the tests (particularly in small sizes). As for load, it's just easier to compare raw numbers against other products since that's what they are using. When you see a product listed at 300Mb/s VPN throughput you know it's max theoretical with no other load. I would like to know if the real world usage with the aes-ni disabled in the GUI is more akin to the command "openssl speed -elapsed aes-256-cbc -multi " or "openssl speed -elapsed -evp aes-256-cbc -multi".
2. You are correct in that it should have been Mb/s. MB/s would be rather nice! :)
Is there any way to test IPSEC performance? I'm under the impression that these tests aren't the same. What I really care about are IPSEC speeds since those are the site-to-site tunnels that would most likely be symmetrical fiber. Anything else would be limited by the ISP upload anyway.
-
- Intel
Pentium Processor N3700 - X11SBA-LN4F Supermicro
- 8 GB S0-DDR3
- Kingston SV300S37A/60G SSDNow V300 interne SSD-Festplatte 60GB
Hello user09,
Did you make your choice ? - Intel
-
thank you all for your answers.
- Intel Pentium Processor N3700
- X11SBA-LN4F Supermicro
- 8 GB S0-DDR3
- Kingston SV300S37A/60G SSDNow V300 interne SSD-Festplatte 60GB
Hello user09,
Did you make your choice ?I have tried the Supermicro Board, but I sent it back, because the idle power usage was 14 - 15 W. In my opinion is that too high for my purposes.
So, I take a look at the expensive SG-2220. For clarity I started a new topic at https://forum.pfsense.org/index.php?topic=117873.0
- Intel
-
Hi
I have tried the Supermicro Board, but I sent it back, because the idle power usage was 14 - 15 W. In my opinion is that too high for my purposes.
So, I take a look at the expensive SG-2220. For clarity I started a new topic at https://forum.pfsense.org/index.php?topic=117873.0
It needs some tweaks for power settings in pfSense but I got the X11SBA-LN4F down to 10 to 11 Watt at idle. This board contains essentially a second computer that runs the IPMI remote management and it draws 3.5 Watt constantly, and it doesn't seem possible to turn it off. The four network ports account for a watt or 2 even if not being used but it may be possible to add some settings to get them to power down if not used. Without the second on board computer for the remote management it would idle at around 7 to 8 Watts which isn't too bad.
Regards
Phil
-
@Phil_D:
10 to 11 Watt at idle.
Unfortunately, for me is that too much.
So now i have two options:
- SG-2220: idle: 6 W
- german server builder:
- Intel Celeron N2930, no AES-NI
- 8 GB DDR3
- 80 GB SATA III Intel SSD MLC 2,5“ (DC S3510)
- max power consumption: 10 W
- idle power consumption: unknown
- LAN Onboard: 2x 1 GBit/s LAN (RJ-45) Intel 82583V
- details: https://www.thomas-krenn.com/en/products/rack-server/technical-datasheet/frame.only_content/key.13078.html
Which would you prefer?
My min. requirements:
- 600 Mbit Firewall Throughput
- 100 Mbit OpenVPN
-
Hate to repeate myself, but the APU2 fits your requirements.
-
using a core2 e6420 with 4gb ram and a 160gb hd here (old old pc) and added 2x intel pcie gigabit nic. for one user, me - works fine for 250/20 cable using squaid, squidguard, snort, pfblocker,etc
would suggest zoltac ci323 with 8gb and a ssd for new home builds on the cheap
