Playing with fq_codel in 2.4

johnpoz

Which is why its not on ;) When you turn on their queues you loose the hardware offload it seems.. So yeah speed takes a hit ;)

belt9

And that is why I am thankful for pfSense!

johnpoz

Oh believe me I will be back to pfsense as soon as get new hardware that can handle the speed.. The usg was a temp solution that was cheap enough to sneak through the budget committee (wife).. its was only a 100$ ;)

It can handle the speed in hardware offload.. But its feature set is so lacking.. Still running my pfsense vm for dhcp and dns since those features on usg need a huge amount of work to be viable in anything other than the most basic of home user networks.. And really just forget about ipv6 and or openvpn without manipulate of json files and having to reload them any time you reprovision the usg from the controller.. And the firewall rules are just nuts to setup on it as well.. I counting the days til I have pfsense back that is for sure ;)

sideout

I ran this on my router at my LAN party and it worked out great. 184 people with a 300mbit modem and 2 100mbit modems , made 2 download shapers and 1 upload shaper.

i made the system patches as well so it would apply after updates.

gsmornot

I should skip this since I don't know what I'm doing but still really curious to make it work. I have gigabit service and get D's and F's on buffer bloat.

I'm sure its in the post and I have indeed read though but still don't understand. What are the steps to enable this? I have 2.4 installed.

Looks like install patches package, run patch posted on page 8 which I was going to do until it said I could not remove this so I thought I better study a bit before I keep going. If you have the energy, please tell me what are the steps and I will follow them. Thanks.

belt9

You don't have to install the patch.

Just set up limiters (look at Johns screenshots a few pages above this) then run the ipfw commands for fq_codel and add them to shellcmd.

Run a speed test and set your limiters to 95% of the speeds you get.

Now go to your firewall rules to pass traffic and in the advanced section just select the queues you just made.

That's it.

w0w

@belt9:

You don't have to install the patch.

Just set up limiters (look at Johns screenshots a few pages above this) then run the ipfw commands for fq_codel and add them to shellcmd.

Run a speed test and set your limiters to 95% of the speeds you get.

Now go to your firewall rules to pass traffic and in the advanced section just select the queues you just made.

That's it.

I don't think it's that simple. If you don't override rules.limiter with own one like TS suggests by patching php code, then any firewall config or even WAN IP change that wants and would reload this file will destroy your manually configured fq_codel, until you manually run ipfw commands again or restart firewall to let shellcmd to do it. Am I wrong?

johnpoz

No sorry it is that simple.. You do not need to make any files changes at all.. Just create the limiters and then put in the commands via shellcmd to put them in every time you reboot, etc.

belt9

Yeah, I just tried adding and deleting firewall rules then checking ipfw and it still has my fq_codel flows.

If there's some other action you're worried might remove fq_codel then just try doing that action then check ipfw after to see if fq_codel is still in place.

ipfw sched show

w0w

OK so may be quick start quide?

1. RTFM for FQ_CODEL http://caia.swin.edu.au/freebsd/aqm/patches/README-0.2.1.txt
2. Config limiters (pipes) via GUI.
3. View /tmp/rules.limiter

for example it will be


pipe 1 config  bw 280576Kb
queue 1 config pipe 1 mask src-ip6 /128 src-ip 0xffffffff

pipe 2 config  bw 280576Kb
queue 2 config pipe 2 mask dst-ip6 /128 dst-ip 0xffffffff

4. USE shellcmd package to recreate pipes with commands like


ipfw pipe flush

ipfw pipe 1 config  bw 280576Kb
ipfw sched 1 config pipe 1 type fq_codel target 7ms quantum 2000 flows 2048
ipfw queue 1 config pipe 1 mask src-ip6 /128 src-ip 0xffffffff

ipfw pipe 2 config  bw 280576Kb
ipfw sched 2 config pipe 2 type fq_codel target 7ms quantum 2000 flows 2048
ipfw queue 2 config pipe 2 mask dst-ip6 /128 dst-ip 0xffffffff

5. Add your limiters to firewall rules (IN/OUT pipes), this step can be any after step 2 actually.

Is it correct?
Maybe it's better to run script at startup? Just placing it into /usr/local/etc/rc.d? I found that using shellcmd is a little bit uncomfortable with multiple command lines at once, have I missed something?

JTravers

Excuse my ignorance on this. I've just learned about and started using pfSense a couple weeks ago.

I have my limiters attached to my "Default allow LAN to any rule" in order to evenly split bandwidth to my LAN clients. And then fq_codel applied to those limiters. Seems to be working great for reducing bufferbloat, ensuring low latency for all clients, etc. Thanks for all the guidance in this thread!

Is there any benefit or harm to doing it that way vs. attaching the limiters to a floating rule as @johnpoz did?

Also, how does all this apply to OpenVPN clients (with pfSense as the server)? Would either setup also work with the OpenVPN clients, or is one setup better than the other?

Thanks for all your help!

belt9

Floating rules vs interface rules won't make a difference. It will also work well on VPN clients. VPN traffic will always have higher latency relative to the same traffic not routed through a VPN. fq_codel can't fix that, but it will still work with fairly queuing the traffic and reducing bufferbloat.

gsmornot

I came back here to say thanks because it works well. I completed my setup differently than some of what has just been posted.

I setup limiters just as seen in the screenshots. (post 121)(upload, download, wan, lan)
I ran the single command for IPFW pipes. (ipfw sched 1 config pipe 1 type fq_codel && ipfw sched 2 config pipe 2)
I installed shellcmd and added the single IPFW statement.
Modified the two stock LAN firewall rules (IPV4 and IPV6 advanced configuration) so that wan and lan would be used just as seen in the screenshots.
I restarted the firewall.

That is all I have done. Prior my buffer bloat was a D to F. Post I get an A each time. I may/may not be setup correctly but whatever it is works. I originally used the wizard for setup of traffic shaping which used HFSC and which gave @425 upload on my gigabit connection. This new setup gives @750. So, good for me.

w0w

Definitely I am blind what screenshots are you all talking about? :D

gsmornot

@w0w:

Definitely I am blind what screenshots are you all talking about? :D

Reply 121 of this thread.

w0w

Thanks. :)

JTravers

@belt9:

Floating rules vs interface rules won't make a difference. It will also work well on VPN clients. VPN traffic will always have higher latency relative to the same traffic not routed through a VPN. fq_codel can't fix that, but it will still work with fairly queuing the traffic and reducing bufferbloat.

I tested floating rules vs. lan rules and they both give excellent results. Latency results in bufferbloat tests seemed to be just slightly lower with the lan rules, but that's just splitting hairs.

I had very poor bufferbloat results when testing through my OpenVPN connection as a client connected to the OpenVPN server in pfSense. Is there any way to fix this? Should I be creating limiters to apply to the OpenVPN interface rules in the firewall and then selecting fq_codel on those limiters, as well?

belt9

Yes you would need to apply limiters to your openvpn interface in order to queue your clients traffic. However, you can only fix your end, if the client is connecting to you via a poor connection then you can't get any better than the worst link.

JTravers

@belt9:

Yes you would need to apply limiters to your openvpn interface in order to queue your clients traffic. However, you can only fix your end, if the client is connecting to you via a poor connection then you can't get any better than the worst link.

Thanks, that makes sense.
I’ll try it out and see how much it helps.

tman222

Finally got around to trying this again, and everything worked great! John's screenshots in reply 121 are spot on and there is no need to edit any files if one uses shellcmd.

I actually recently changed to a 100/100 Fiber connection - here are results (using the DSL Reports speed test which has a nice Bufferbloat check):

Before (no shaping):

Using ALTQ FAIRQ + Codel Active Queue Management; 100Mbit Limit on Both WAN and LAN:

Using fq_codel and 100Mbit Limit on Both Upload and Download:

What's interesting to me here is that fq_codel appears to perform a bit better than the ALTQ emulation of fq_codel (using FAIRQ + Codel) - I find this very interesting. Anyone have any thoughts as to why?

I also ran a more intense FLENT test on another system with fq_codel enabled and the results looked great as well (stable ping and stable download/upload over the course of the test).

Given the relatively little effort required to get this to work on pfSense, it's a fantastic way to improve the stability of a connection.