Playing with fq_codel in 2.4

tman222

Upgraded to 2.4.3 yesterday evening and fq_codel still working as expected.

Did you edit any files when you set it up originally? Is there anything particularly unique about your setup, e.g. running fq_codel on VLANs, etc.? Also when you do run a speed test and then keep refreshing ipfw sched show during the process, do you see traffic being passed?

Hope this helps.

dennypage

No VLANs, no file edits, using shell command:

ipfw sched 1 config pipe 1 type fq_codel; ipfw sched 2 config pipe 2 type fq_codel

Here are some ipfw sched show outputs from during the download portion of a dslreports test using http:

00001: 150.000 Mbit/s    0 ms burst 0 
q00001  50 sl. 0 flows (256 buckets) sched 1 weight 1 lmax 0 pri 0 droptail
    mask:  0x00 0x00000000/0x0000 -> 0xffffffff/0x0000
 sched 1 type FQ_CODEL flags 0x0 0 buckets 1 active
 FQ_CODEL target 5ms interval 100ms quantum 1514 limit 10240 flows 1024 ECN
   Children flowsets: 1 
BKT Prot ___Source IP/port____ ____Dest. IP/port____ Tot_pkt/bytes Pkt/Byte Drp
  0 ip           0.0.0.0/0             0.0.0.0/0     2285  3421723 193 289500  10
00002:  20.000 Mbit/s    0 ms burst 0 
q00002  50 sl. 0 flows (256 buckets) sched 2 weight 1 lmax 0 pri 0 droptail
    mask:  0x00 0xffffffff/0x0000 -> 0x00000000/0x0000
 sched 2 type FQ_CODEL flags 0x0 0 buckets 1 active
 FQ_CODEL target 5ms interval 100ms quantum 1514 limit 10240 flows 1024 ECN
   Children flowsets: 2 
  0 ip           0.0.0.0/0             0.0.0.0/0      290    15423  0    0   0

00001: 150.000 Mbit/s    0 ms burst 0 
q00001  50 sl. 0 flows (256 buckets) sched 1 weight 1 lmax 0 pri 0 droptail
    mask:  0x00 0x00000000/0x0000 -> 0xffffffff/0x0000
 sched 1 type FQ_CODEL flags 0x0 0 buckets 1 active
 FQ_CODEL target 5ms interval 100ms quantum 1514 limit 10240 flows 1024 ECN
   Children flowsets: 1 
BKT Prot ___Source IP/port____ ____Dest. IP/port____ Tot_pkt/bytes Pkt/Byte Drp
  0 ip           0.0.0.0/0             0.0.0.0/0     3793  5686580 90 135000  15
00002:  20.000 Mbit/s    0 ms burst 0 
q00002  50 sl. 0 flows (256 buckets) sched 2 weight 1 lmax 0 pri 0 droptail
    mask:  0x00 0xffffffff/0x0000 -> 0x00000000/0x0000
 sched 2 type FQ_CODEL flags 0x0 0 buckets 1 active
 FQ_CODEL target 5ms interval 100ms quantum 1514 limit 10240 flows 1024 ECN
   Children flowsets: 2 
  0 ip           0.0.0.0/0             0.0.0.0/0      369    19572  0    0   0

00001: 150.000 Mbit/s    0 ms burst 0 
q00001  50 sl. 0 flows (256 buckets) sched 1 weight 1 lmax 0 pri 0 droptail
    mask:  0x00 0x00000000/0x0000 -> 0xffffffff/0x0000
 sched 1 type FQ_CODEL flags 0x0 0 buckets 1 active
 FQ_CODEL target 5ms interval 100ms quantum 1514 limit 10240 flows 1024 ECN
   Children flowsets: 1 
BKT Prot ___Source IP/port____ ____Dest. IP/port____ Tot_pkt/bytes Pkt/Byte Drp
  0 ip           0.0.0.0/0             0.0.0.0/0     5577  8331991 140 208833  22
00002:  20.000 Mbit/s    0 ms burst 0 
q00002  50 sl. 0 flows (256 buckets) sched 2 weight 1 lmax 0 pri 0 droptail
    mask:  0x00 0xffffffff/0x0000 -> 0x00000000/0x0000
 sched 2 type FQ_CODEL flags 0x0 0 buckets 1 active
 FQ_CODEL target 5ms interval 100ms quantum 1514 limit 10240 flows 1024 ECN
   Children flowsets: 2 
  0 ip           0.0.0.0/0             0.0.0.0/0       50     3092  0    0   0

00001: 150.000 Mbit/s    0 ms burst 0 
q00001  50 sl. 0 flows (256 buckets) sched 1 weight 1 lmax 0 pri 0 droptail
    mask:  0x00 0x00000000/0x0000 -> 0xffffffff/0x0000
 sched 1 type FQ_CODEL flags 0x0 0 buckets 1 active
 FQ_CODEL target 5ms interval 100ms quantum 1514 limit 10240 flows 1024 ECN
   Children flowsets: 1 
BKT Prot ___Source IP/port____ ____Dest. IP/port____ Tot_pkt/bytes Pkt/Byte Drp
  0 ip           0.0.0.0/0             0.0.0.0/0      427   634711 91 136500   0
00002:  20.000 Mbit/s    0 ms burst 0 
q00002  50 sl. 0 flows (256 buckets) sched 2 weight 1 lmax 0 pri 0 droptail
    mask:  0x00 0xffffffff/0x0000 -> 0x00000000/0x0000
 sched 2 type FQ_CODEL flags 0x0 0 buckets 1 active
 FQ_CODEL target 5ms interval 100ms quantum 1514 limit 10240 flows 1024 ECN
   Children flowsets: 2 
  0 ip           0.0.0.0/0             0.0.0.0/0      184     9635  0    0   0

Of course, if I use https for dslreports, the problem is not nearly as bad (as you would expect).

I'm not using fq_codel, but I am using fairq+codel.
I've noticed since updating to 2.4.3 that a speedtest gives me exactly 50Mb/s

This is interesting, because this is exactly the BW I have set on my LAN queue for web traffic.

Previously a speedtest would burst high up towards the 100Mb/s my connection is.

Downloading torrents etc still seems to be fine, that is multiple sessions seem to be unaffected. Also fast.com checks report up around 70-80MB/s. But Speedtest is always ~exactly the 50Mb/s I've set for web traffic.

But certainly 2.4.3 seems to have changed something with regards to traffic shaping etc.

Apologies for taking the fq_codel thread slightly offtopic!

Nullity

@muppet:

I'm not using fq_codel, but I am using fairq+codel.
I've noticed since updating to 2.4.3 that a speedtest gives me exactly 50Mb/s

This is interesting, because this is exactly the BW I have set on my LAN queue for web traffic.

Previously a speedtest would burst high up towards the 100Mb/s my connection is.

Downloading torrents etc still seems to be fine, that is multiple sessions seem to be unaffected. Also fast.com checks report up around 70-80MB/s. But Speedtest is always ~exactly the 50Mb/s I've set for web traffic.

But certainly 2.4.3 seems to have changed something with regards to traffic shaping etc.

Apologies for taking the fq_codel thread slightly offtopic!

Yeah, AFAIK, limiters (dummynet) & fairq+codel (ALTQ) are very much separated in software. Though, your bug is still interesting. Maybe.

w0w

dennypage
The best way to check is it related to pfSense is to downgrade and re-test it again. You can also try to lower your bandwidth limits or play with KPTI option.
As for me, nothing changed in bufferbloat, but I have over provisioned hardware.

kripz

Anybody know why dslreports doenst how bufferbloat? It never gives me a score regardless of settings on that website.

@kripz:

Anybody know why dslreports doenst how bufferbloat? It never gives me a score regardless of settings on that website.

It depends on where you are. If you live in Australia or NZ, it doesn't seem to work for us (it gives an error and doesn't repot anything)

dennypage

@w0w:

dennypage
The best way to check is it related to pfSense is to downgrade and re-test it again. You can also try to lower your bandwidth limits or play with KPTI option.
As for me, nothing changed in bufferbloat, but I have over provisioned hardware.

KPTI doesn’t affect it. Wouldn’t expect it to as limiters are kernel code. I’ve tested with half available bandwidth, and still encounter the bloat issue. I don’t think I’m under provisioned with hardware -– I have a 4860 running a 150/20 connection.

I’m assuming that this is the result of a FreeBSD kernel change. I haven’t downgraded and run a test to confirm yet, but hat’s about what I’m down to.

I’m taking it that you haven’t seen any change with a multichannel http test?

Gatekeeper-ZA

I have been having endless years of shaping due to out poor LTE service in South Africa.
Just want to Say THANKS to all for this guide. I although did add a little twist. am still running
HSFC traffic shaper with Limiters children in addition to queues from the traffic shaper I can
still manage my ports as before just give them a nice hard piece of codel if needed.
due to speeds in my area fluctuating alot the schedules works wonders to "dynamically"
change the pipe has not brought ping down from 100 to +- 30 - 43ms which is huge.
another thing is that when using the traffic shaper with fq_codel I can still watch netflix / youtube
full hd no buffering while gaming @ acceptable latency.

Tests were done while streaming netflix minimal impact my girlfriend didnt even notice this while
playing CS:GO test added 0.3-4ms to her game.

Note Due to intentional latency being terrible please dont work on the latency results from dslreports.
Note Speeds are currently Set @ 10mb / 10Mb 2Pipes 4Children Each 75 / 50 / 5 / 2
Depending where I have lay them in the sharper determines which children I am using.
Yep I know its weird but for me it works.

result.png_thumb

after.png_thumb
![local speedtest.net before.png](/public/imported_attachments/1/local speedtest.net before.png)
![local speedtest.net before.png_thumb](/public/imported_attachments/1/local speedtest.net before.png_thumb)
![local speedtest.net after.png](/public/imported_attachments/1/local speedtest.net after.png)
![local speedtest.net after.png_thumb](/public/imported_attachments/1/local speedtest.net after.png_thumb)

TheNarc

I just wanted to report that I did run some tests over the weekend using 2.4.3 and don't see any differences (i.e. fq_codel still seems to be working for me). I tested using the dslreports speed test and also ran flent's rrul and rrul_torrent tests. I realize that just another report of "works for me" isn't especially helpful, though it does seem to point to some specific configuration issue rather than a wholesale breakdown of fq_codel in 2.4.3.

dennypage

@TheNarc:

I just wanted to report that I did run some tests over the weekend using 2.4.3 and don't see any differences (i.e. fq_codel still seems to be working for me). I tested using the dslreports speed test and also ran flent's rrul and rrul_torrent tests. I realize that just another report of "works for me" isn't especially helpful, though it does seem to point to some specific configuration issue rather than a wholesale breakdown of fq_codel in 2.4.3.

No, it still helps. Just to be sure, when you test with dslreports, you used http rather than https, yes? My tests with https still show an A most of the time, but http is showing C/D. I haven't run anything with rrul.

TheNarc

That's a very interesting point. I didn't explicitly select HTTP, and I use the HTTPS Everywhere plugin, so I quite possibly was testing with HTTPS. I'm at work, but when I get home this evening I'll run a test with HTTP and get back to you. Are you aware of a specific reason why that may make a difference, or just know that it does based on your testing?

dennypage

I ran some tests with flent/rrul, and it doesn't show any issue at all. I also ran a rrul with the limiters disabled. The bad results with limiters disabled confirmed that basic fq_codel is working. :)

Of note is that rrul seems to be hard coded to use 4 streams only. Testing with DSLReports restricted to 4 streams (http/websocket) doesn't show an issue either.

DSLReports with 8 streams is marginally okay. Above 12 streams or so, DSLReports starts to tank. By the time it gets to 24 streams, it's digging big holes in the ground.

As it seems to be an issue with the number of simultaneous streams, I'm going to try multiple lan systems running simultaneous tests next.

w0w

dennypage
http://www.dslreports.com/speedtest/31667858 plain http

But I found that wifi clients have different situation — bufferbloat is rated like "С" and I remember that last summer I have activated QoS on the wifi access point to eliminate this problem and now looks like it does not work anymore, I don't think it's related to pfSense, but may be to wifi client that have updated against spectre/meltdown android kernel. I

dennypage

In general my testing is wired, both Linux (Chrome & Firefox) and Mac (Safari and Chrome). I've tested wireless with Mac and the results appear similar at first blush, but I haven't done a lot of testing there.

TheNarc

I would expect that with wireless, all bets are off. I run all my testing wired as well. I did run one test last night with 24 streams each up and down and still didn't see degradation on the HTTP dslreports test. I forget what hardware you were running with. Have you monitored CPU usage while running the tests? That seems like a long shot for sure, but if I understand correctly, more flows equals more queues, so queue management becomes a higher burden.

w0w

My testing was also wired. 32 streams with Hi-Res BufferBloat.
@dennypage:

In general my testing is wired, both Linux (Chrome & Firefox) and Mac (Safari and Chrome). I've tested wireless with Mac and the results appear similar at first blush, but I haven't done a lot of testing there.

If I were you, I would try to disable all shapers, limiters, leaving just plain firewall and let it run again, to see is it worse or better. I just think that it can be overloaded ISP upstream router, but the simpliest way to check it is to downgrade pfSense or connect some laptop directly to your ISP modem or router and re-test.

Gatekeeper-ZA

Hey Guys have been playing around some more. could someone please help with my config it seems that my pipe is not selecting the correct que
I have tried please see attached screenshot. all seems to be working correct except for me not being able to use the queues on the in/out
on firewall rules problem still persists after reboot. thanks in advance for the help.

fq_codel_ssh.png_thumb

dennypage

@TheNarc:

I forget what hardware you were running with. Have you monitored CPU usage while running the tests?

It's a 4860. Peak CPU @ ~25%, average under 20%.

dennypage

@w0w:

If I were you, I would try to disable all shapers, limiters, leaving just plain firewall and let it run again, to see is it worse or better.

Yes, I ran rrul tests with and without limiters enabled, confirming the basic operation of fq_codel with 4 streams.