I5 5250U 4 LAN Home computer Q355G4 install question

Waqar.UK

Thanks.

I thought I would no longer need my 8 port tp-link switch as currently I have on lan port on my mini tower i5 being used which is one of two ethernet ports of a pci x2 HP gigabit (Intel based) card. This lan goes to my 8 port tp-link which then via ethernet connects to my desktop, power line network and finally to my Asus wireless router. I thought I could set up my new pfsense with a seperate ethernet port for each device mentioned above.

phil.davis

@Waqar.UK:

I thought I could set up my new pfsense with a seperate ethernet port for each device mentioned above.

Yes, you can do that, and you can choose to either
a) bridge the 3 pfSense ethernet ports to make a single LAN, or
b) create 3 separate interfaces, each with a different subnet, and each will happen to have just a single device in it.

If you choose (a), you are saying that you are happy with all the devices in a single broadcast domain/subnet. In that case, I would keep the switch, plug the switch into a single pfSense ethernet port, and plug the devices into the switch - I would not do bridging.

If you choose (b) then each device is firewalled-off from the other devices. You need to add rules to allow the devices to talk to each other as desired. Software that does "automated discovery" of devices in a broadcast domain/subnet is not going to work (and so it depends if you care about that or not)

These things are design choices that depend on connectivity requirements, performance requirements, and the level of technical detail of setup that you want to manage.

Most home people will do something like:

attach all home devices to a switch
attach the switch to pfSense LAN
(maybe) add another access point for guests and attach that to a different pfSense interface/subnet, and give it different firewall rules so that their guests cannot hack into the home devices, or so the guests get limited bandwidth or…

Waqar.UK

I will do (a). So much simpler and all my devices will be protected.

CaladorGCS

Bought the same unit! 8) If you have the opportunity I was wondering if you could check what your idle tempature is and let me know? I believe I'm running a bit hot.

Waqar.UK

@PingTheNet:

Bought the same unit! 8) If you have the opportunity I was wondering if you could check what your idle tempature is and let me know? I believe I'm running a bit hot.

According to pfsense, core temp is 27.8 Celcius.

My one runs warm but not hot.

Waqar.UK

@PingTheNet:

Bought the same unit! 8) If you have the opportunity I was wondering if you could check what your idle tempature is and let me know? I believe I'm running a bit hot.

Here are my pfsense temps.

![new pfsense temps.png](/public/imported_attachments/1/new pfsense temps.png)
![new pfsense temps.png_thumb](/public/imported_attachments/1/new pfsense temps.png_thumb)

CaladorGCS

@Waqar.UK:

@PingTheNet:

Bought the same unit! 8) If you have the opportunity I was wondering if you could check what your idle temperature is and let me know? I believe I'm running a bit hot.

According to pfsense, core temp is 27.8 Celcius.

My one runs warm but not hot.

Ok, that what I have now. When I ran it for the first hour. My Bios said it was 91 C but then it cooled down a lot after that. My guess the thermal paste needed to warm up to create a good seal.

Waqar.UK

Your passive heat sink, is it warm or hot to your fingertips?

phochiom

I also bought the same box from Qotom. It arrived today, pre-configured with 8 GB (Kingston branded) and 120 GB m.2 SSD (Phison branded).
Tried to install pfSense 2.3.3. I only have a TV that supports HDMI, so I could not see the whole text, especially at the bottom where is asks you to configure the various steps. So obviously I could not configure to my liking.
Just wanted to ask: is there a specific order for the 4 LAN ports to attach the WAN cable and the LAN? I used LAN1 for WAN and LAN2 for LAN (I attached a Netgear R7000 with stock firmware acting as Access Point and had IP 192.168.1.2). I could not get to the GUI of pfSense at 192.168.1.1 (neither with http or https).
So I guess I will need to buy a monitor with HDMI port to be able to configure pfSense.
Any help, or ideas, is appreciated.
Thanks

Waqar.UK

I used a VGA to HDMI adapter that can be picked up for a few £/$ which was connected to my really old 15" LG flat panel monitor. See if you can find these and it will work out cheaper than buying a new HDMI monitor.

https://www.amazon.co.uk/TechRise-High-Speed-adapter-Converter-Charging/dp/B01E8DD6J6/ref=sr_1_3?ie=UTF8&qid=1491644265&sr=8-3&keywords=vga+to+hdmi+converter

There is a specific order to assign a LAN or WAN port on this mini PC. Setup asks for the WAN, then LAN.

phochiom

Thanks, didn't know about these converters, will save me some money. With regards to LAN ports, can you please tell me which number did you assign to Windows? I assume it should be 1, or maybe it doesn't matter. I'm on Virgin Media 200/10 and would use only 2 of the LAN ports, 1 for Windows and 2 for LAN, which will go to my R7000 LAN 1.

CaladorGCS

@phochiom:

I also bought the same box from Qotom. It arrived today, pre-configured with 8 GB (Kingston branded) and 120 GB m.2 SSD (Phison branded).
Tried to install pfSense 2.3.3. I only have a TV that supports HDMI, so I could not see the whole text, especially at the bottom where is asks you to configure the various steps. So obviously I could not configure to my liking.
Just wanted to ask: is there a specific order for the 4 LAN ports to attach the WAN cable and the LAN? I used LAN1 for WAN and LAN2 for LAN (I attached a Netgear R7000 with stock firmware acting as Access Point and had IP 192.168.1.2). I could not get to the GUI of pfSense at 192.168.1.1 (neither with http or https).
So I guess I will need to buy a monitor with HDMI port to be able to configure pfSense.
Any help, or ideas, is appreciated.
Thanks

Mine were out of order too and I had to swich them using Option 2 on th PfSence unit. Used the MAC to figure out the order. Mine was ordered 1, 4, 2, 3.

occamsrazor

Hi,

Just curious what kind of installation you are doing… on USB keys or on the SSD?
I was reading this and like the idea of using ZFS:
https://forum.pfsense.org/index.php?topic=126597.0
...but on the other hand using the SSD seems like it would be fastest.

Thanks.

Waqar.UK

I used this as a guide to install https://doc.pfsense.org/index.php/Installing_pfSense

To write images: https://doc.pfsense.org/index.php/Writing_Disk_Images - Image Writer for Windows / Win32 Disk Imager is much easier to SSD.
I just plugged in my wan when setup asked to plug in my wan cable and same for lan.

occamsrazor

Thanks, that guide is useful although I plan to install 2.4 straight away. From what I read 2.4 uses a different install type:

https://doc.pfsense.org/index.php/2.4_New_Features_and_Changes#Operating_System_.2F_Architecture_changes

I'm just planning ahead to see what will be the best combination of media on which to install on in terms of SSD (and if size?) or USB keys (if so 1 or 2 keys and what size?). I'll ask a question on the 2.4.0 ZFS How To thread.

Waqar.UK

@occamsrazor:

Thanks, that guide is useful although I plan to install 2.4 straight away. From what I read 2.4 uses a different install type:

https://doc.pfsense.org/index.php/2.4_New_Features_and_Changes#Operating_System_.2F_Architecture_changes

I'm just planning ahead to see what will be the best combination of media on which to install on in terms of SSD (and if size?) or USB keys (if so 1 or 2 keys and what size?). I'll ask a question on the 2.4.0 ZFS How To thread.

Use a SSD, I had a spare 120GB Kingston hyperx that I was planning to use for a different project.
To install, any drive, I used a 4GB sandisk usb 2.0 that I bought many years ago.

occamsrazor

@PingTheNet:

Mine were out of order too and I had to swich them using Option 2 on th PfSence unit. Used the MAC to figure out the order. Mine was ordered 1, 4, 2, 3.

Mine were also out of order. igb0 is 1 and igb1 is 4.

What is this "Option 2" method you speak of for changing them?

phochiom

@occamsrazor:

@PingTheNet:

Mine were out of order too and I had to swich them using Option 2 on th PfSence unit. Used the MAC to figure out the order. Mine was ordered 1, 4, 2, 3.

Mine were also out of order. igb0 is 1 and igb1 is 4.

What is this "Option 2" method you speak of for changing them?

Same here for NICs, exactly same order.

ChefRayB

Ordered: QOTOM Q355G4 I5 5250U 8GB RAM 120GB SSD
Delivery: 15-28 days

I will report after I receive it and install pfSense on the box. I plan to install OpenVPN client and compare the bandwidth against my laptop.

reference:

https://www.aliexpress.com/store/product/QOTOM-Q355G4-2017-New-fanless-X86-4-LAN-Micro-Computer-I5-5250U-Dual-core-onboard-1080P/108231_32800711474.html

ChefRayB

Update: Received hardware Q355G4, exactly as described by other users

Please keep in mind to install AMD64 pfsense packages.

If you install i386 package, the package installation will work but you will encounter CAS Latency timeouts when formatting SSD and reboot loops.