Problems with IPsec vpn between pfSense and Oracle Cloud Infrastructure

RodrigoCBraga · Sep 4, 2018, 4:09 PM

Thank you for help.

My question is regarding the rules for establishing communication after the ipsec tunnel is established and how do I monitor traffic?
On the other side I asked the logs to try to identify if the internal network communication 192.168.1.0/24 is being blocked.
Thank you again.

Derelict · Sep 4, 2018, 4:16 PM

Firewall rules on IPsec govern connections originating from the other side of the IPsec tunnels.

Firewall rules on the local interfaces govern connections coming into the firewall from the hosts connected there.

https://www.netgate.com/docs/pfsense/firewall/firewall-rule-basics.html

https://www.netgate.com/docs/pfsense/firewall/firewall-rule-troubleshooting.html

https://www.netgate.com/docs/pfsense/book/firewall/troubleshooting-firewall-rules.html

As for "Monitoring" that is a fairly generic term. What are you actually looking to do?

RodrigoCBraga · Sep 4, 2018, 4:34 PM

@derelict said in Problems with IPsec vpn between pfSense and Oracle Cloud Infrastructure:

As for "Monitoring" that is a fairly generic term. What are you actually looking to do?

I'm trying to identify on which side is the problem.
If it is some configuration in pfSense or OCI.
I performed some tests as a tracert and did not succeed when I ran the tracert from a workstation on the 192.168.1.0/24 network.
On the other hand was informed that I could try to access via remote desktop to a certain ip on the internal network 10.72.0.0/16.
Both tests failed.
The phase 2 setup is the same as the one you set.
Thank you for your help.

Derelict · Sep 4, 2018, 4:41 PM

You can packet capture on the IPsec interface (enc0) to see if pings are going out, replies are being received, etc.

RodrigoCBraga · Sep 6, 2018, 3:19 PM

Thanks for your help.
The client said that analyzing the logs and with a similar problem they had with a PaloAlto solution is necessary to include a new remote network 0.0.0.0/0.
I need help to do this procedure, because when I try to create a network there is no / 0 option. Can you help me?

Security Parameter Index

The Oracle Cloud Infrastructure VPN headends use next-hop-based tunnels. When you create a new IPSec connection, you specify a list of IPv4 networks that should be routed from your dynamic routing gateway (DRG) through the IPSec tunnel to your CPE.

Oracle IPSec ProxyIDs

local=0.0.0.0/0
remote=0.0.0.0/0
service=any

https://docs.cloud.oracle.com/iaas/Content/Network/Reference/genericCPE.htm

Derelict · Sep 6, 2018, 3:58 PM

Site-to-site tunnels to 0.0.0.0/0 will catch all traffic from the source network including traffic to the internet. I would not recommend doing that, and it is doubtful Oracle cloud IPsec requires it.

If the networks in your Phase 2 are the problem, that will show in the IPsec logs. Check the log settings )VPN> IPsec, Advanced) and be sure that IKE SA, IKE Child SA, and Configuration Backend are set to Diag. Everything else can be Control.

Look at where it is failing and compare with this:

https://www.netgate.com/docs/pfsense/vpn/ipsec/ipsec-troubleshooting.html

Or, of course, you can post the logs here.

When you create a new IPSec connection, you specify a list of IPv4 networks that should be routed from your dynamic routing gateway (DRG) through the IPSec tunnel to your CPE.

Right. All of those routed networks should be specified as Local Networks in Phase 2 entries on your side. The Cloud CIDR should be the Remote Network for all of them.

RodrigoCBraga · Sep 6, 2018, 10:12 PM

LogPart1
LogPart2
LogPart3
LogPart4
LogPart5
LogPart6
IPSEC
IPSEC RULES
NATOUTBOUND
RULES WAN
STATE FILTER
STATIC RULES

My set up.
I hope you can help me.
Thanks.

Derelict · Sep 6, 2018, 10:36 PM

Delete any static routes you added like that 10.72.0.0/16 to 192.168.1.1. That is not how IPsec works.

Honestly, it looks like your IPsec is doing what you asked it to do. Need to find out why the host in the cloud (10.72.112.30) isn't responding or why your traffic isn't coming back. That's more of an oracle question.

RodrigoCBraga · Sep 6, 2018, 10:44 PM

This post is deleted!

RodrigoCBraga · Sep 13, 2018, 4:51 PM

I have a doubt.
In pfsense it is possible to do configuration where in phase 2 has the network 0.0.0.0/0 as local and remote?
Attached, screen with configuration between Palo Alto firewall and Oracle Cloud Infrastructure.
Palo Alto Phase 2

RodrigoCBraga · Sep 19, 2018, 2:39 PM

@derelict
Hello, can you still help me?

Derelict · Sep 19, 2018, 3:33 PM

Help how?

RodrigoCBraga · Sep 19, 2018, 3:36 PM

@derelict said in Problems with IPsec vpn between pfSense and Oracle Cloud Infrastructure:

Help how?
Yes.

I have a doubt.
In pfsense it is possible to do configuration where in phase 2 has the network 0.0.0.0/0 as local and remote?
Attached, screen with configuration between Palo Alto firewall and Oracle Cloud Infrastructure.
Palo Alto Phase 2

Ernani · Sep 20, 2018, 7:14 PM

@derelict

Hello, I would like to ask your attention to verify Oracle documentation and to comment that Pfsense is compatible and support Oracle VPNAAS.
1 - Oracle documentation to a Generic CPE:
https://docs.cloud.oracle.com/iaas/Content/Network/Reference/genericCPE.htm

Requirements for generic CPE devices are:

local=0.0.0.0/0
remote=0.0.0.0/0
service=any

Please let us know your thoughts about that.

Regards,
Ernani

Derelict · Sep 20, 2018, 7:35 PM

Personal opinion:

I think that is completely uncalled for.

On pfSense that will catch all traffic and send it over the tunnel unless extreme measures are taken to bypass it. And there is no way to bypass traffic from the firewall itself.

I cannot see how Oracle expects that to work for people.

Again, you should be able to create Phase 2 entries with your cloud subnet as remote and your local subnet(s) as local.

Ernani · Sep 20, 2018, 7:56 PM

@derelict

I agree with you, since I have configured others tunnels with different suppliers to Oracle without use that requirement, but I saw some intermittencies.

Thank you,
Ernani