Pfsense 2.1 on watchguard firebox x6500e still safe / usefull?
-
hello all,
I have a question: i own a watchguard firebox x6500e with pfsense 2.1 installed,
Is this config still safe to use?
I have it running in a lab environment right now and want to use it for my home network as a router / firewall for the time being (in the near future am looking to upgrade to a more suitable solution / box, but for now it would be a terrific steppingstool)
I am coming off a m0n0wall router / firewall that (as we speak) in still in service and perfoms great to (almost) all my networking needs
Thx in advance ;)
-
I wouldn't use it as is. Is there some specific reason you can't upgrade it to 2.4.3?
-
Well, last time i used it i tried to upgrade it and it crashed... the guy that sold me the unit said that this was the latest version of pfsense i could run without problems.... so i just took his word on that and never tried it
-
It won't go to 2.4 as it's 32bit only but you should be able to get to 2.3.5.
However you might be running an old Nano image on a smaller card. 2GB is the smallest image available for 2.3.X.
Steve
-
Thanx Steve,
I’ll give a try tomorrow and post my finding here -
@dutchie Post it on the left-hand side.
-
@kom come again??..
-
Allright.... it WORKS!!!!!
What i did...
Had an older 4gb cf card that showed dma problems, so i started with a fresh new 16gb card..
Downloaded pfsense 2.3.5 from the website with nano (embedded) en serial console, i386
Flashed the card with win32diskimager
At first i was getting the same dma crap.. so google to the rescue..
Booted, and when it prompted to go to shell i did that
Added a line similar to set hint.ata.0.mode=POI4
That worksed for the install, needed to make it stick during bootup, so waited for the install to complete and did a vi /boot/loader.conf.local
Added the line (hint.ata.0.mode=POI4) saved the changes :w :q and rebooted the box....
All worked out... box is running in a test cycle now
@stephenw10 : can i assume this version of pfsense 2.3.5 is still safe enough to connect to the interwebs as a router / firewall?
-
Yes. You should see the patch update to 2.3.5p2 available. That is the current version though it's likely to be the last release in the 2.3.5 branch.
Steve
-
@dutchie 'Twas but a jest...
https://www.youtube.com/watch?v=dFtLONl4cNc
Riffing on "Pass the dutchie on the left-hand side..."
I'll see myself out.
-
@kom said in Pfsense 2.1 on watchguard firebox x6500e still safe / usefull?:
'Twas but a jest...
Ha! See, that's the very purpose of emoticons.
-
Gentlemen,
I would like to thank you for resurrection the x6500e,
It’s in working condition right now, and i am happy with it (allthough it still produces a lot of noise even with the fans spinning at BB in the bios)
This box will be a great steppingstool to learn about pfsense and upgrade later to a dedicated box with more hardware power
Thx again for all you help ;)
-
You can set the fans to a lower speed using WGXepc. BB (or maybe BA) is the lowest speed the BIOS can take because the fan tacho reading for some reason hits a limit and hangs. Once booted though you can go lower.
32bit binary that should run on your box. It been a while since I tried the 32bit version though the last box I had still ran it at 2.3.4.
Source code if it doesn't and you need to recompile it:
https://github.com/stephenw10/WGXepcSteve
-
@stephenw10 I couldn't find the emoticon of Elon Musk holding a spliff.