How to install this thing without formatting and erasing data
-
What NICs does it give as choices? Some don't work well with the autodetect, try just assigning it manually.
Steve
-
@stephenw10 Yes I assigned it manually the only one available is re0 for WAN interface then after saying no to vlan and continuing installation it goes back to the start
-
Would you like to assign VLANs should be the first question. Then enter re0 for the WAN. Then just hit enter to finish.
You will only have a single interface but you can investigate why it didn't detect the other NIC once it's booted.
Steve
-
@stephenw10 yes I know I just didn't write in order.
I have redone it now after restarting my PC same problem after clicking enter to finish it asks "do you want to proceed [yln]?" and I click enter again and it goes back to "should vlan be set up now [yln]?".... Am I in a critical situation rn XD -
This post is deleted! -
Hmm, hard to know what might cause that. I can only imagine that happening if the interface it just assigned is lost for some reason or it's unable to save the config created.
I assume you are seeing this after booting from USB and installing successfully?
Steve
-
@stephenw10 yes it gives some unusual messages ig:
warning: configuration references interfaces that do not exist: em0 em1
network interface mismatch -- running interface assignment option
Mismatch?
I have rebooted from the pfsense USB installer after installing successfully to the USB pfsense installed on
-
Oh my USB is just 8gb is that enough for pfsense ?
-
Oh looks like re0 for WAN is (down).....
But it's the only interface under "valide interfaces are"
And it lets me assign it normally for WAN
-
The fact it's still referencing em0 and em1 means it's still trying to use the default config.
The installer itself will fit on 1GB. Did you boot from one USB stick and install onto a different USB stick?
It seems like it's possibly still booting at least partially from the installer which might be why it's using the default config.
Steve
-
So now your trying to install it on your PC via a usb stick as its drive What do you think that is going to get you?
If you want to play with it - install it on a VM!!!
An intelligent man is sometimes forced to be drunk to spend time with his fools
If you get confused: Listen to the Music Play
Please don't Chat/PM me for help, unless mod related
SG-4860 24.11 | Lab VMs 2.7.2, 24.11 -
@stephenw10 I made sure it's installing from the USB not the USB installer by removing it still showing em0 and em1
-
@johnpoz what's the difference if I'm keeping the USB connected or closing the vm after configurating the network? Back to my first question about configuration activity lol
-
OMG dude you don't get what psfsense does if you think you can just close it down once you have "configured" something..
See that router you linked too - that is what pfsense does... If you turned off your router could you get to the internet??
-
@johnpoz oh so I have to keep VM running... That's not good for my core i5 lol
-
What exactly are you wanting to accomplish exactly... Cuz you clearly do not understand what pfsense even is.
-
@johnpoz if I don't understand what pfsense is then why would I be trying to install it XD I just didn't understand how it basically works and you made it clear to me
-
Please what did you think pfsense was going to do for you "exactly"...
-
@johnpoz run through my router. Thats why I thought my configuration would still be active if I closed pfsense drive or VM but it turned out to be my new router
-
@Alpha-Radke said in How to install this thing without formatting and erasing data:
run through my router.
What does that even mean? What is it that your router is not doing for you that you feel pfsense could do for you? But not be running? Are you looking for something to administer your router other than its web gui?
