Bypass At&t fiber BGW210-700
-
No way I can answer that without knowing how you have it connected. However it looks like you donlt have em interfaces at all from your previous posts. If that's have you have it configured in pfSense and the script is still the same then the ONT should be on igb0 and the BGW210-700 on igb1.
Steve
-
Ok I have tried both
ONT on em0 and the BGW210-700 on em1.(1) ONT from outside goes to EM0
(2) ONT from Residential Gateway goes to EM1
dpinger refuses to start1 6 0xffffffff80200000 2ddcbe8 kernel
2 1 0xffffffff83221000 10a0 cpuctl.ko
3 1 0xffffffff83223000 a34 ng_etf.ko
[2.4.4-RELEASE][admin@pfSense.localdomain]/root:em1: permanently promiscuous mode enabled
em0: permanently promiscuous mode enabled
em0: link state changed to UP
em1: link state changed to UP
em1: link state changed to DOWN
pflog0: promiscuous mode enabled
em4: link state changed to UP
em2: link state changed to UP
em3: link state changed to UP
em1: link state changed to UP
[2.4.4-RELEASE][admin@pfSense.localdomain]/root: -
What happened when you got yo step 7 here: https://github.com/aus/pfatt#install
Did you see the ngeth0 interface and assign it as WAN?
Since you are re-assigning the interfaces it shouldn't matter which one you use as long as they are actually connected to the devices you set in the script.
Check the log file the script makes each time it runs: /var/log/pfatt.log
There should be some good troubleshooting info there if it's still not working.Steve
-
- Next, we spoof the MAC address of the residential gateway and request a DHCP lease on ngeth0. The packets get tagged as VLAN0 and exit to the ONT.
are you talking about this step above
...if so I did place my residential gateway mac in PFatt,sf. does it need to go someplace else?I never got any prompts to configure any thing on boot up..can I configure manually from GUI?
-
@stephenw10 said in Bypass At&t fiber BGW210-700:
find / -name "ng_etf"
WOOOOOOOOOOHOOOOOOOOOOOO IT'S WORKING MUCH THANKS STEVE OH MY GOD I THANK YOU SO MUCH FOR ALL YOUR TIME AND EFFORT....I really need to follow instructions better. THANKS FOR YOUR PATIENTS WITH ME YOU WERE ABSOLUTELY AWESOME IN EVERY RESPECT!!!!!!BYE BYE BGW210-700
-
Nice!
-
Can I use the wireless portion of the BGW210-700 as an access point or is it completely out of the equation at this point?
-
Short answer: no.
It may be possible to configure something but I would not. It would be though the AT&T router so all the nat and firewall would apply there as well as in pfSense. It would be entirely separate from the LAN. Also you would probably be the only person running that config so it's hard to say what you might run into.
Steve
-
Thanks Steve...I also lost some speed dropped to 100 Mbits I have Gig fiber. I reset the the BGW210-700 to factory defaults brought up the network and did a speeds test through the BGW210-700 and it came back to 997 on the download and 837 on the upload...I then rebooted the Pfsense and connect. Ran another speed test again and they came back normal. Is this something I will have to do normally?
-
I would not expect so. I do not have that type of connection though so I have no way to know for sure. @sherpagoodness may be able to tell what to expect.
Steve
-
@sherpagoodness Hey since I bypassed ATT BGW210-700... my speed dropped to 100 Mbits I have Gig fiber. I reset the the BGW210-700 to factory defaults brought up the network and did a speeds test through the BGW210-700 and it came back to 997 on the download and 837 on the upload...I then rebooted the Pfsense and connect. Ran another speed test again and they came back normal. I just checked it a gain and it's back to 100 mbits... Is this something I will have to do normally?
-
@stephenw10 I was recently running into the same issue with the package install as well. Currently running pfsense 2.4.5, when trying to pull the package and install I'm getting "no packaged available to install mactching 'ng_etf-kmod'. Were these pulled or no longer available, or is it related to differing versions?
-
Hmm, it does appear to be missing. Digging.....
-
Ok, you should not need to install that pkg any longer as the Netgraph etf module is now in the base install:
[2.4.5-RELEASE][root@pfsense.fire.box]/root: kldstat -v | grep ng_etf 533 ng_etfSteve
-
@stephenw10 that explains it then, I had originally used the pre compiled file which was meant for x64 and not ARM (I believe) and then after upgrade removed the file thinking it was the the pre compiled and not the new one.
Any chance I can still pull the arm kernel from somewhere, or if it I just reset the device will it get restored?
-
Hmm, I don't believe it in the ARM kernel. What device do you have?
-
@stephenw10 I just got the SG-1100 a few days ago.
Also tried the factory reset, looking in /boot/kernel I don’t see the file now.
-
Ok, it doesn't appear to be in the aarch64 kernel either. The pkg was available for all architectures in 2.4.4 though.
I have asked about it internally.Steve
-
Thanks @stephenw10 it you could let me know I would appreciate it!
-
[spam was here]
