PFSense Release 2.5 + OpenVPN 2.5 broken? Any fixes?
-
@n8lbv Tried a couple of this and there is some more data.
-
@n8lbv This error-
Jan 28 14:17:51 openvpn 39698 ioctl(TUNSIFMODE): Device busy (errno=16)does not appear to be an issue from reading.
Also I can't find any indication that multiple IP addresses on the WAN should be any issue.When setting up the OVPN server the WAN dropdown list includes both what I am using as a primary WAN IP and my secondary use WAN IP.
It is clear that you can select either for the OVPN server and that I am selecting the one that I want.
This apparently should not be any kind of an issue. -
Nope, that's normal (reversed) logs when the server starts.
Do you see states in the firewall when clients try to connect?
-
@stephenw10 Yes somwhere he posted today I showed that there are states. (replying from my phone browser) at the bar :)
-
@n8lbv When posted earlier :) but yes. states exist!
-
Pretty much clueless and right back to where I started ages ago when 2.5.0 was released.
No clue what to try next and no luck success or further information with all of the normal checks and suggestions.This is why most of my customer sites are still stuck on 2.4.5
VPN guaranteed to break after upgrading.
And doing a fresh install and trying to get all of the individual site config/settings manually reconfigured will not be an easy option for me at all.And pulling over the config backup from a 2.4.5 system after clean installing 2.5.2 has not worked either.
Same issue, VPN functionality ends up like what I have here. braindead.
-
@n8lbv Hi, When you do one of this updates, are you verifying that the Default Gateway is correct in your SYSTEM-ROUTING settings? Can you access the internet ok and ping say 8.8.8.8 from the PFSENSE ping utility?
I was seeing issues with my update to 2.5.2 as well, and my OPEN VPN's were not working.
Turns out that my gateway was messed up in my Routing settings.
However, I could NOT get PFS to update properly with multiple installs from the GUI!
When I did a backup of the 2.4 config then a FRESH install of 2.5.2, with the 2.4 config on the usb drive, it grabbed it and applied all the settings at the end of the install.
Then after it is up, it had to update my packages. (you will get a message at top of PFS about packages will be updated and check back later or such) Well if I remember correctly I believe that at least once even with the fresh install it the package updates crashed PFS. I could not access the GUI even though the firewall was still functioning.
PFS suggests that you DO NOT UPDATE packages before trying a system update and ALSO that you UNINSTALL ALL PACKAGES BEFORE you try to update if you are seeing problems!
Maybe a package is messing you up?
Now I'm not sure how it knows, but when I did this with a package, it still knew and kept all my settings!
Maybe try this. Maybe a package is wrecking your VPN's somehow. And check you Routing (and DNS settings) like mentioned above, make sure PFS is getting out to the internet and getting proper DNS function.
MP
-
@mrpushner Thanks for the reply.
No problems at all with default (and only) gateway settings.
And system works perfectly fine other than I have been unable to get an IPSEC or openVPN server to work on them after upgrading yet ever.
I have tried pretty much everything that I could think of including following the directions and uninstalling all packages before upgrading) then reinstalling packages after upgrading.
--> t\The only package I have installed is the client export package. This was simple and not a lot of work.At this troubleshooting stage I am only testing setting up an OpenVPN Server as to not confuse or complicate matters.
Fact is IPSEC does not work as expected either. But I am trying to keep initial troubleshooting easy here.A simple OPENVPN server (Remote Access SSL/TLS + User Auth) on the server.
And a windows remote client.Pretty much using the default settings that PFSense sets for you when setting this up.
It works on any clean install box with a single public IP (static or dynamic) that I have tested.
It is not working on any of my production systems that have both been upgraded from 2.4.5 to 2.5.2 and have two static public IP addresses configured.
When setting up the server I am clearly selecting the intended "main" public IP I intend to use.
The firewall rules and packet captures and firewall logging all seem to be working as expected.
VPN server seems braindead and nothing is logged when connection attempts are made.
Only logging you see from the openVPN server is when it is started up or manually restarted or when the system is rebooted and the service starts up.I feel more like I do now.
-
@n8lbv Humm...then something (like PFS rule maybe) has to be blocking the attempts to connect to the server. Have you checked the FW logs when trying to connect? Any blocks to that Ip from your client source?
Just seems to me that with TWO Static IP's setup, its like the client request is not ever getting to the server. How does PFS handle multiple IP addresses? I can't answer that. Maybe its a limitation with the VPN protocols? I'm not sure.
Can you ping either of the VPN server IP's from the client successfully?
Did you try disabling IPv6?
Have you setup a dual IP setup and confirmed its does not work, then removed one IP, REBOOT and tested again?
None of my systems use multiple IP's so I can't comment on that.
It just seems to me that if ALL your systems see the same things, it could be the SAME settings in each that are doing it.
When connection attemps are made to the open VPn server I get entries like this:
Jan 28 10:30:45 openvpn 77264 xxx.xx.xx.xx:39600 peer info: IV_VER=2.5.0
or "Authenticate/Decrypt packet error: missing authentication info"
entries.
If you get nothing, then my guess is there is confusion with your multiple static IPS setup.
Drop one IP and try again, if it works, re-add it and see what happens.
Also make sure you have server set as IP4 only.
Not sure what else to suggest. Maybe try to WAN PFS guru's on the forum.
Have you reviewed this:
https://docs.netgate.com/pfsense/en/latest/multiwan/openvpn.html
MP
-
@n8lbv If it's too much for you, I can offer remote technical support at a very low cost.
-
@mrpushner Not blocking the packets, and I am logging the rule and seeing the pass logs.
If you scroll up just a little bit I showed one example.
:) -
@silence It's not too much, I intend to figure it out, learn something and then share back to this thread what I learned and what fixed it as this may also help anyone else that runs into this.
-
@n8lbv ok so if it's not too much for you i can help you here, what i would recommend is to do a backup and then a fresh install of pfsense the latest stable version and try to upload your clean config please...this should work for you simple and fast in 15 minutes you have your vpn working without problem.
-
@silence I will try this.
I think I already did try this back when I was troubleshooting 2.5.0
But it's been so long now I am not sure so yes I need to retry that.
Thanks. :) -
@n8lbv I think you mean to try to restore my backup after a fresh install.. I will try that soon and report back with results.
-
@n8lbv, I have different sites, some with 2.4, 2.5 and 2.5.2, the version doesn't matter, it always works the first time...!
just try it without configuring anything else extra.
-
@silence said in PFSense Release 2.5 + OpenVPN 2.5 broken? Any fixes?:
some with 2.4, 2.5 and 2.5.2
And these 2.4.5 and 2.5.2 are "OpenVPN" "site-to-site" interconnected ?
I guess it is possible, but "VPN" settings on both sides have to be fine tuned.pfSense 2.4.5px uses the OpenVPN version 2.4.8 (or 9).
pfSense 2.5.2 uses :OpenVPN 2.5.2 amd64-portbld-freebsd12.2 [SSL (OpenSSL)] [LZO] [LZ4] [MH/RECVDA] [AEAD] built on Jun 24 2021 ....That's 2.5.2; pure coincidence that pfSense and OpenVPN have the same version number.
Btw : the latest OpenVPN, today, is 2.5.5Between OpenVPN 2.4.x and OpenVPN 2.5.2, there were enough changes to make things break: RTFCL here : See "Overview of changes since OpenVPN 2.4".
As soon as you see a "soon to be depreciated'" in the **OpenVPN log today, you should redo the setup asap so that "depreciated option" message are not shown any-more.
The thing is : this is nearly never done. "As it works right now - I don't touch it" and "I'm not looking at the logs now and won't start doing so tomorrow ;)".When the the big upgrade is presented, like pfSense from 2.4.5 to 2.5.x, this includes OpenVPN 2.4.x to 2.5.0, a major upgrade version shift - the connection breaks.
Btw : pfSense OpenVPN site to site - client to VPN like "Exp*ssVPN" or OpenVPN as a remote pfSense admin access works for for me
I rarely use the site to site, less often the client OpenVPN, but most often the "have to work from home" option. -
@gertjan Hi, I had 3 total sites all on 2.4.4. I updated (via GUI) my Server site to 2.5.2. SITE TO SITE open VPN's continued to work fine. So two client sites on 2.4.4 to Server site on 2.5.2.
As soon I updated one of my client sites to 2.5.2, VPN crashed.
I had to go to the site and restore back to 2.4.4 to get it to work again.
Since then, I did a fresh install of 2.5.2 on that client site (on my spare PFS hardware), and applied my 2.4.4 backup config, and it came back online normally.
I did not determine the exact cause of this problem.
MP
-
@mrpushner This seem to be the state I am in and what has happened.
I no longer have backup configs from 2.4.5 or 2.4.4 so I do not have the option to
restore from those on my sites that I have updated to 2.5 about 1 year ago.
But it may be an option for me on all of the sites that are still on 2.4.5 if that proves to be a way of fixing them.Right now I have a couple of sites that have been upgraded around a year ago that are now on 2.5.2 and would like to add VPN but cannot because of this problem.
And doing a fresh install and manually restoring all of the settings would be a lot of work :)
The reality is that I may have to do that for this issue.I can also try restoring from a current backup after a fresh install.
To see if the problem follows the config or not.
I am NOT backing up ANY VPN settings configs or certificates.
In all cases the VPN setup is brand new.
And is still broken on any system I try to bring up that has not been a fresh install. -
@mrpushner said in PFSense Release 2.5 + OpenVPN 2.5 broken? Any fixes?:
Hi, I had 3 total sites all on 2.4.4. I updated (via GUI) my Server site to 2.5.2. SITE TO SITE open VPN's continued to work fine. So two client sites on 2.4.4 to Server site on 2.5.2.
As soon I updated one of my client sites to 2.5.2, VPN crashed.Oh ... great.
My "common sense" would say :
if 2.4.4 (really ?? 2.4.4 ??? 2.4.4 is way to old) to 2.4.4 works.
and
2.4.4 to 2.5.2 works
then
2.5.2 to 2.5.2 should also work.A bit like
"Windows 7 networking" to "Windows 7 networking" worked.
"Windows 7 networking" to "Windows 10 networking" worked.
"Windows 10 networking 10" to "Windows 10 networking" fails ....Ok, sorry for me ranting.
@mrpushner said in PFSense Release 2.5 + OpenVPN 2.5 broken? Any fixes?:
I did not determine the exact cause of this problem.
Two things are needed :
Clean restart of VPN server and the logs from that moment.
Clean start of the client and the logs from that moment.Important : there are no 2.4.4 users on this forum. As 2.4.4 dates from .... dono, 2019 - 2018 ? I can't recall what the details were from that old OpenVPN version - and the 2.4.4 pfSense GUI - and the old pfSense quirks.
So, tests should be done with a "2.5.2" to "2.5.2".
Please, don't paste log text here in the forum. Use https://pastebin.com/ and paste the link here.
No "help me" PM's please. Use the forum, the community will thank you.
Edit : and where are the logs ??
