Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    Proscend 180-t vdsl2 SFP Support

    Hardware
    8
    43
    8.8k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • R
      rcoleman-netgate Netgate @ETSAU
      last edited by

      @etsau They're not the same NICs, and thus not the same drivers.
      On the 4100/6100 they are Intel SoC NICs, on the 2100 they're Marvell.

      Ryan
      Repeat, after me: MESH IS THE DEVIL! MESH IS THE DEVIL!
      Requesting firmware for your Netgate device? https://go.netgate.com
      Switching: Mikrotik, Netgear, Extreme
      Wireless: Aruba, Ubiquiti

      ETSAUE 1 Reply Last reply Reply Quote 0
      • ETSAUE
        ETSAU @rcoleman-netgate
        last edited by

        @rcoleman-netgate do you see this as being something that's fixable in some way? Not sure about other regions but we're seeing a good amount of interest (Australia), and it's really a very tidy solution for the 2100

        I'm willing to put a bit of effort in to see what we can do.

        R 1 Reply Last reply Reply Quote 0
        • R
          rcoleman-netgate Netgate @ETSAU
          last edited by

          @etsau I'll leave this ticket for my colleague to see in the morning... he has better thoughts when it comes to the hardware and engineering side. If he has anything for me to test in the lab he'll reach out to me directly.

          Not sure what we can do about reproducing your specific media converter, however. It might be a limitation of the hardware device itself.

          Ryan
          Repeat, after me: MESH IS THE DEVIL! MESH IS THE DEVIL!
          Requesting firmware for your Netgate device? https://go.netgate.com
          Switching: Mikrotik, Netgear, Extreme
          Wireless: Aruba, Ubiquiti

          ETSAUE 1 Reply Last reply Reply Quote 0
          • ETSAUE
            ETSAU @rcoleman-netgate
            last edited by

            @rcoleman-netgate Thank you very much for your assistance there. FWIW, we are a partner for Australia.

            1 Reply Last reply Reply Quote 0
            • stephenw10S
              stephenw10 Netgate Administrator
              last edited by

              What does ifconfig -m mvneta0 show in either state?

              ETSAUE 1 Reply Last reply Reply Quote 0
              • ETSAUE
                ETSAU @stephenw10
                last edited by

                @stephenw10 the below are my notes from doing the testing on the 2100 a couple days ago - I didn't use the -m argument; but can re-run using the -m if needed:

                OKAY - so; from boot (of a factory defaulted 2100)
PROSCEND modem was inserted from boot (and had line sync...)
enabled ssh; checked interface stats:
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
        media: Ethernet autoselect (none)
        status: active
        nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>

Followed by a re-seat: (no other changes):
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
        media: Ethernet autoselect (1000baseSX <full-duplex>)
        status: active
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>


graceful restart:
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
        media: Ethernet autoselect (none)
        status: active
        nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>

Followed by a re-seat:
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
        media: Ethernet autoselect (1000baseSX <full-duplex>)
        status: active
        nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>

                Is this sufficient or would you like me to get fresh results with the "-m"?

                1 Reply Last reply Reply Quote 0
                • stephenw10S
                  stephenw10 Netgate Administrator
                  last edited by

                  The -m flag asks ifconfig to show what media types it thinks are available which could be important here since the presence of the module would dictate that. If the NIC for some reason simply doesn't see the module or maybe sees it as the wrong type that could be a clue.

                  Steve

                  ETSAUE 1 Reply Last reply Reply Quote 0
                  • ETSAUE
                    ETSAU @stephenw10
                    last edited by

                    @stephenw10 Please find below the ifconfig logs requested. The initial set are after a restart with the SPF module installed. The second is with the unseating are reseating of the SPF module, pfSense remained on during the seating of the card.

                    After device startup

                    [22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig mvneta0
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
        media: Ethernet autoselect (none)
        status: active
        nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>

[22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig -m mvneta0
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        capabilities=804bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LRO,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
        media: Ethernet autoselect (none)
        status: active
        supported media:
                media autoselect
                media 1000baseSX mediaopt full-duplex
                media 1000baseSX
                media 1000baseT mediaopt full-duplex,master
                media 1000baseT mediaopt full-duplex
                media 1000baseT mediaopt master
                media 1000baseT
                media 100baseTX mediaopt full-duplex
                media 100baseTX
                media 10baseT/UTP mediaopt full-duplex
                media 10baseT/UTP
                media none
        nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>
[22.05-RELEASE][admin@pfSense.home.arpa]/root:

                    Un-seat and re-seating SFP module

                    [22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig mvneta0
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
        media: Ethernet autoselect (1000baseSX <full-duplex>)
        status: active
        nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>
		
[22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig -m mvneta0
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        capabilities=804bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LRO,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
        media: Ethernet autoselect (1000baseSX <full-duplex>)
        status: active
        supported media:
                media autoselect
                media 1000baseSX mediaopt full-duplex
                media 1000baseSX
                media 1000baseT mediaopt full-duplex,master
                media 1000baseT mediaopt full-duplex
                media 1000baseT mediaopt master
                media 1000baseT
                media 100baseTX mediaopt full-duplex
                media 100baseTX
                media 10baseT/UTP mediaopt full-duplex
                media 10baseT/UTP
                media none
        nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>
[22.05-RELEASE][admin@pfSense.home.arpa]/root:
                    1 Reply Last reply Reply Quote 0
                    • stephenw10S
                      stephenw10 Netgate Administrator
                      last edited by

                      Hmm, so more like it just doesn't see the device in the combo port.

                      If you connect an active cable to the RJ-45 port and disconnect it without removing the SFP module does that trigger the port switch and allow it to come up?

                      Steve

                      ETSAUE 1 Reply Last reply Reply Quote 0
                      • ETSAUE
                        ETSAU @stephenw10
                        last edited by

                        @stephenw10 We have run through the tests suggested on the RJ-45 port and included two additional tests which may assist you. Please see below the results:

                        After device startup

                        [22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig mvneta0
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
        media: Ethernet autoselect (none)
        status: active
        nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>

[22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig -m mvneta0
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        capabilities=804bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LRO,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
        media: Ethernet autoselect (none)
        status: active
        supported media:
                media autoselect
                media 1000baseSX mediaopt full-duplex
                media 1000baseSX
                media 1000baseT mediaopt full-duplex,master
                media 1000baseT mediaopt full-duplex
                media 1000baseT mediaopt master
                media 1000baseT
                media 100baseTX mediaopt full-duplex
                media 100baseTX
                media 10baseT/UTP mediaopt full-duplex
                media 10baseT/UTP
                media none
        nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>

                        Plugged in active RJ-45 cable alongside SFP module in the combo port

                        [22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig mvneta0
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
        media: Ethernet autoselect (none)
        status: active
        nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>

[22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig -m mvneta0
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        capabilities=804bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LRO,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
        media: Ethernet autoselect (none)
        status: active
        supported media:
                media autoselect
                media 1000baseSX mediaopt full-duplex
                media 1000baseSX
                media 1000baseT mediaopt full-duplex,master
                media 1000baseT mediaopt full-duplex
                media 1000baseT mediaopt master
                media 1000baseT
                media 100baseTX mediaopt full-duplex
                media 100baseTX
                media 10baseT/UTP mediaopt full-duplex
                media 10baseT/UTP
                media none
        nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>

                        Cable removed from RJ-45 in combo port

                        [22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig mvneta0
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
        media: Ethernet autoselect (none)
        status: active
        nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>

[22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig -m mvneta0
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        capabilities=804bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LRO,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
        media: Ethernet autoselect (none)
        status: active
        supported media:
                media autoselect
                media 1000baseSX mediaopt full-duplex
                media 1000baseSX
                media 1000baseT mediaopt full-duplex,master
                media 1000baseT mediaopt full-duplex
                media 1000baseT mediaopt master
                media 1000baseT
                media 100baseTX mediaopt full-duplex
                media 100baseTX
                media 10baseT/UTP mediaopt full-duplex
                media 10baseT/UTP
                media none
        nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>

                        Cable plugged in, Cycle interface state, down then up.

                        [22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig mvneta0
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
        media: Ethernet autoselect (none)
        status: active
        nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>

[22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig -m mvneta0
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        capabilities=804bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LRO,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
        media: Ethernet autoselect (none)
        status: active
        supported media:
                media autoselect
                media 1000baseSX mediaopt full-duplex
                media 1000baseSX
                media 1000baseT mediaopt full-duplex,master
                media 1000baseT mediaopt full-duplex
                media 1000baseT mediaopt master
                media 1000baseT
                media 100baseTX mediaopt full-duplex
                media 100baseTX
                media 10baseT/UTP mediaopt full-duplex
                media 10baseT/UTP
                media none
        nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>

[22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig mvneta0 down

[22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig mvneta0
mvneta0: flags=8a02<BROADCAST,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 tentative scopeid 0x1
        media: Ethernet autoselect (none)
        status: active
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>

[22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig -m mvneta0
mvneta0: flags=8a02<BROADCAST,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        capabilities=804bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LRO,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 tentative scopeid 0x1
        media: Ethernet autoselect (none)
        status: active
        supported media:
                media autoselect
                media 1000baseSX mediaopt full-duplex
                media 1000baseSX
                media 1000baseT mediaopt full-duplex,master
                media 1000baseT mediaopt full-duplex
                media 1000baseT mediaopt master
                media 1000baseT
                media 100baseTX mediaopt full-duplex
                media 100baseTX
                media 10baseT/UTP mediaopt full-duplex
                media 10baseT/UTP
                media none
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>

[22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig mvneta0 up

[22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig mvneta0
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
        media: Ethernet autoselect (none)
        status: active
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>

[22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig -m mvneta0
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        capabilities=804bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LRO,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
        media: Ethernet autoselect (none)
        status: active
        supported media:
                media autoselect
                media 1000baseSX mediaopt full-duplex
                media 1000baseSX
                media 1000baseT mediaopt full-duplex,master
                media 1000baseT mediaopt full-duplex
                media 1000baseT mediaopt master
                media 1000baseT
                media 100baseTX mediaopt full-duplex
                media 100baseTX
                media 10baseT/UTP mediaopt full-duplex
                media 10baseT/UTP
                media none
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>

                        Cable out, cycle interface down then up.

                        [22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig mvneta0
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
        media: Ethernet autoselect (none)
        status: active
        nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>

[22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig -m mvneta0
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        capabilities=804bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LRO,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
        media: Ethernet autoselect (none)
        status: active
        supported media:
                media autoselect
                media 1000baseSX mediaopt full-duplex
                media 1000baseSX
                media 1000baseT mediaopt full-duplex,master
                media 1000baseT mediaopt full-duplex
                media 1000baseT mediaopt master
                media 1000baseT
                media 100baseTX mediaopt full-duplex
                media 100baseTX
                media 10baseT/UTP mediaopt full-duplex
                media 10baseT/UTP
                media none
        nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>

[22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig mvneta0 down

[22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig mvneta0
mvneta0: flags=8a02<BROADCAST,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 tentative scopeid 0x1
        media: Ethernet autoselect (none)
        status: active
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>

[22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig -m mvneta0
mvneta0: flags=8a02<BROADCAST,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        capabilities=804bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LRO,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 tentative scopeid 0x1
        media: Ethernet autoselect (none)
        status: active
        supported media:
                media autoselect
                media 1000baseSX mediaopt full-duplex
                media 1000baseSX
                media 1000baseT mediaopt full-duplex,master
                media 1000baseT mediaopt full-duplex
                media 1000baseT mediaopt master
                media 1000baseT
                media 100baseTX mediaopt full-duplex
                media 100baseTX
                media 10baseT/UTP mediaopt full-duplex
                media 10baseT/UTP
                media none
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>

[22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig mvneta0 up

[22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig mvneta0
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
        media: Ethernet autoselect (none)
        status: active
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>

[22.05-RELEASE][admin@pfSense.home.arpa]/root: ifconfig -m mvneta0
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        capabilities=804bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LRO,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
        media: Ethernet autoselect (none)
        status: active
        supported media:
                media autoselect
                media 1000baseSX mediaopt full-duplex
                media 1000baseSX
                media 1000baseT mediaopt full-duplex,master
                media 1000baseT mediaopt full-duplex
                media 1000baseT mediaopt master
                media 1000baseT
                media 100baseTX mediaopt full-duplex
                media 100baseTX
                media 10baseT/UTP mediaopt full-duplex
                media 10baseT/UTP
                media none
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
                        1 Reply Last reply Reply Quote 0
                        • stephenw10S
                          stephenw10 Netgate Administrator
                          last edited by

                          Hmm, so no observable change...

                          You tried setting the interface to 1000baseSX <full-duplex> fixed?

                          ETSAUE 1 Reply Last reply Reply Quote 0
                          • ETSAUE
                            ETSAU @stephenw10
                            last edited by

                            @stephenw10 yes indeed - we've tried a few of the of static media states (we originally thought the interface HAD to be set to 1000base SX) - but since disproved that.

                            When we have the link set statically, the ifconfig output shows:

                            mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        description: WAN
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        media: Ethernet 1000baseSX <full-duplex> (none)
        status: active
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>

                            Quite the conundrum.
                            If it's interesting, we did have to be on firmware 21.01 or later before the sfp port would work at all.

                            1 Reply Last reply Reply Quote 0
                            • stephenw10S
                              stephenw10 Netgate Administrator
                              last edited by

                              Hmm, there may not be much we can do here. The combo port in the 2100 is hardcoded to be only 1000baseSX in the SFP. It doesn't detect the media there.
                              The correct fix here would probably be at the driver level or even in the hardware description but to so that would require significant developer resources for a device relatively few users will ever see. That's unlikely to happen unfortunately. An alternative might be a startup script that power cycled the module. I'm looking to see if that's possible.

                              If one of our developers in Australia hits this they might suddenly be motivated. 😉

                              Steve

                              ETSAUE 1 Reply Last reply Reply Quote 0
                              • ETSAUE
                                ETSAU @stephenw10
                                last edited by

                                Thanks @stephenw10 ,

                                Do you have any insights on why the device is fine in all the other models, and only the 2100 has issues? I don't have anyone with skills to edit drivers or firmware for either of the devices; but it just seems a shame that the modem works fine if inserted after boot; but the 2100 can't detect it if present at boot.

                                I appreciate there would be a reasonable workaround to power cycle the port - do you know of any way I can do that? (obviously a down / up on the interface has no effect).

                                1 Reply Last reply Reply Quote 0
                                • stephenw10S
                                  stephenw10 Netgate Administrator
                                  last edited by stephenw10

                                  The 2100 WAN port is a unique combination or hardware. It's the mvneta NIC from the SoC but with a combo PHY to give us the SFP port. In order to make that work the SFP port is hard wired to be 1000base-SX and that limits it's flexibility.
                                  I'm not aware of any way to power cycle it unfortunately but let me see if I can find anything...

                                  Do you see any errors shown from sysctl dev.mvneta.0 when it's not detected?

                                  Steve

                                  ETSAUE 1 Reply Last reply Reply Quote 0
                                  • ETSAUE
                                    ETSAU @stephenw10
                                    last edited by

                                    @stephenw10, thank you for taking another look at this error condition. We have run the requested command on the device in both the initial startup condition, and after manually reseating the SFP module.

                                    Initial boot diagnostics:

                                    [22.05-RELEASE][root@pfSense.home.arpa]/root: ifconfig -m mvneta0               mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        capabilities=804bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LRO,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        media: Ethernet autoselect (none)
        status: no carrier
        supported media:
                media autoselect
                media 1000baseSX mediaopt full-duplex
                media 1000baseSX
                media 1000baseT mediaopt full-duplex,master
                media 1000baseT mediaopt full-duplex
                media 1000baseT mediaopt master
                media 1000baseT
                media 100baseTX mediaopt full-duplex
                media 100baseTX
                media 10baseT/UTP mediaopt full-duplex
                media 10baseT/UTP
                media none
        nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>

                                    [22.05-RELEASE][root@pfSense.home.arpa]/root: sysctl dev.mvneta.0               
dev.mvneta.0.lpi: 0
dev.mvneta.0.flow_control: 0
dev.mvneta.0.mib.reset: 0
dev.mvneta.0.mib.watchdog: 0
dev.mvneta.0.mib.overrun: 0
dev.mvneta.0.mib.rx_discard: 0
dev.mvneta.0.mib.mac_late_collision: 0
dev.mvneta.0.mib.mac_collision: 0
dev.mvneta.0.mib.mac_crc_err: 0
dev.mvneta.0.mib.mac_rx_err: 0
dev.mvneta.0.mib.pkt_jabber: 0
dev.mvneta.0.mib.pkt_oversize: 0
dev.mvneta.0.mib.pkt_fragment: 0
dev.mvneta.0.mib.pkt_undersize: 0
dev.mvneta.0.mib.fc_rx_bad: 0
dev.mvneta.0.mib.fc_rx_good: 0
dev.mvneta.0.mib.fc_tx: 0
dev.mvneta.0.mib.tx_mac_ctl_err: 0
dev.mvneta.0.mib.tx_bcast_frame: 0
dev.mvneta.0.mib.tx_mcast_frame: 0
dev.mvneta.0.mib.tx_exces_collision: 0
dev.mvneta.0.mib.tx_good_frame: 0
dev.mvneta.0.mib.tx_good_oct: 0
dev.mvneta.0.mib.rx_fame_1024_max: 0
dev.mvneta.0.mib.rx_frame_512_1023: 0
dev.mvneta.0.mib.rx_frame_256_511: 0
dev.mvneta.0.mib.rx_frame_128_255: 0
dev.mvneta.0.mib.rx_frame_65_127: 0
dev.mvneta.0.mib.rx_frame_1_64: 0
dev.mvneta.0.mib.rx_mcast_frame: 0
dev.mvneta.0.mib.rx_bcast_frame: 0
dev.mvneta.0.mib.rx_bad_frame: 0
dev.mvneta.0.mib.rx_good_frame: 0
dev.mvneta.0.mib.tx_mac_err: 0
dev.mvneta.0.mib.rx_bad_oct: 0
dev.mvneta.0.mib.rx_good_oct: 0
dev.mvneta.0.rx.queue0.threshold_timer_us: 100
dev.mvneta.0.%parent: simplebus1
dev.mvneta.0.%pnpinfo: name=ethernet@30000 compat=marvell,armada-3700-neta
dev.mvneta.0.%location:
dev.mvneta.0.%driver: mvneta
dev.mvneta.0.%desc: NETA controller

                                    After manually reseating the SFP module:

                                    [22.05-RELEASE][root@pfSense.home.arpa]/root: ifconfig -m mvneta0
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=800bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LINKSTATE>
        capabilities=804bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LRO,LINKSTATE>
        ether 00:e0:ed:bc:2e:eb
        inet6 fe80::2e0:edff:febc:2eeb%mvneta0 prefixlen 64 scopeid 0x1
        media: Ethernet autoselect (1000baseSX <full-duplex>)
        status: active
        supported media:
                media autoselect
                media 1000baseSX mediaopt full-duplex
                media 1000baseSX
                media 1000baseT mediaopt full-duplex,master
                media 1000baseT mediaopt full-duplex
                media 1000baseT mediaopt master
                media 1000baseT
                media 100baseTX mediaopt full-duplex
                media 100baseTX
                media 10baseT/UTP mediaopt full-duplex
                media 10baseT/UTP
                media none
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>

                                    [22.05-RELEASE][root@pfSense.home.arpa]/root: sysctl dev.mvneta.0
dev.mvneta.0.lpi: 0
dev.mvneta.0.flow_control: 0
dev.mvneta.0.mib.reset: 0
dev.mvneta.0.mib.watchdog: 0
dev.mvneta.0.mib.overrun: 0
dev.mvneta.0.mib.rx_discard: 0
dev.mvneta.0.mib.mac_late_collision: 0
dev.mvneta.0.mib.mac_collision: 0
dev.mvneta.0.mib.mac_crc_err: 0
dev.mvneta.0.mib.mac_rx_err: 0
dev.mvneta.0.mib.pkt_jabber: 0
dev.mvneta.0.mib.pkt_oversize: 0
dev.mvneta.0.mib.pkt_fragment: 0
dev.mvneta.0.mib.pkt_undersize: 0
dev.mvneta.0.mib.fc_rx_bad: 0
dev.mvneta.0.mib.fc_rx_good: 0
dev.mvneta.0.mib.fc_tx: 0
dev.mvneta.0.mib.tx_mac_ctl_err: 0
dev.mvneta.0.mib.tx_bcast_frame: 99
dev.mvneta.0.mib.tx_mcast_frame: 19
dev.mvneta.0.mib.tx_exces_collision: 0
dev.mvneta.0.mib.tx_good_frame: 118
dev.mvneta.0.mib.tx_good_oct: 36560
dev.mvneta.0.mib.rx_fame_1024_max: 0
dev.mvneta.0.mib.rx_frame_512_1023: 0
dev.mvneta.0.mib.rx_frame_256_511: 99
dev.mvneta.0.mib.rx_frame_128_255: 14
dev.mvneta.0.mib.rx_frame_65_127: 5
dev.mvneta.0.mib.rx_frame_1_64: 0
dev.mvneta.0.mib.rx_mcast_frame: 0
dev.mvneta.0.mib.rx_bcast_frame: 0
dev.mvneta.0.mib.rx_bad_frame: 0
dev.mvneta.0.mib.rx_good_frame: 0
dev.mvneta.0.mib.tx_mac_err: 0
dev.mvneta.0.mib.rx_bad_oct: 0
dev.mvneta.0.mib.rx_good_oct: 0
dev.mvneta.0.rx.queue0.threshold_timer_us: 100
dev.mvneta.0.%parent: simplebus1
dev.mvneta.0.%pnpinfo: name=ethernet@30000 compat=marvell,armada-3700-neta
dev.mvneta.0.%location:
dev.mvneta.0.%driver: mvneta
dev.mvneta.0.%desc: NETA controller
                                    1 Reply Last reply Reply Quote 0
                                    • stephenw10S
                                      stephenw10 Netgate Administrator
                                      last edited by

                                      Since that module is really a complete router by itself if could be doing something odd when uboot sets up the NICs initially. In both the warm reboot and the cold boot scenario the NIC is first configured by uboot to use for PXE booting.

                                      One thing you could try is setting mvneta1 as the interface uboot uses. To do that you would need to interrupt the boot to reach the uboot prompt (Marvell>>) then run:

                                      setenv ethprime eth1
saveenv
reset

                                      You should then see:

                                      Net:   eth0: neta@30000, eth1: neta@40000 [PRIME]

                                      I tested that here and it still boots fine. Though it would no longer PXE boot from WAN.
                                      It's hard to imagine that will fix it though.

                                      Is there any way to reset the module without unplugging it?
                                      Does it have any sort of management interface?

                                      Unfortunately they seem to be basically unavailable or incredibly expensive in the UK.

                                      1 Reply Last reply Reply Quote 0
                                      • stephenw10S stephenw10 referenced this topic on
                                      • stephenw10S stephenw10 referenced this topic on
                                      • S
                                        skoota
                                        last edited by

                                        Hi All,

                                        Apologies being yet another person to resurrect this thread, but I have been reading this with significant interest. I am helping out a friend in Queensland with their business network and recommending they get a Netgate 4100 - long story short, we need two WAN ports for a primary ADSL2 connection and failover 4G connection.

                                        Originally I was thinking we would need to purchase a separate ASDL modem, but this thread seems to indicate we can instead use the Transcend 180-T vDSL2 SFP module...is my thinking correct? An all-in-one solution would be perfect.

                                        They are using Aussie Broadband as their provider. Their connection is marketed as NBN VDSL but it's quite clearly ADSL2 since there is literally a phone cable plugging into the back of their Aussie Broadband provided router/modem into the DSL port (by the way, this router/modem is not particularly good or working for them...thus my recommendation to go to pfSense).

                                        Being fortunate enough to have NBN FTTH myself I haven't had the "pleasure" of dealing with an ADSL connection in quite some time, so I am not fully across things like VPI/VCI settings...having a look at the settings on the current model it uses VSDL Profile 17a if that is releavant.

                                        Anyway, this is a long way of asking do you think this is going to work? I'd hate to recommend something to them which then doesn't end up working!

                                        Thanks in advance for any advice!

                                        P 1 Reply Last reply Reply Quote 0
                                        • P
                                          Patch @skoota
                                          last edited by

                                          @skoota said in Proscend 180-t vdsl2 SFP Support:

                                          Their connection is marketed as NBN VDSL

                                          I use the an external modem (ISP supplied) in bridge mode.
                                          That way if there are connections issues, I can reset the modem to factory default an confirm it is not a fault with my equipment.

                                          S 1 Reply Last reply Reply Quote 0
                                          • S
                                            skoota @Patch
                                            last edited by

                                            @patch Thanks, but I am keen to eliminate the provided Aussie Broadband modem (as it's not particularly reliable) and, if possible, would like an all-in-one solution (rat than a separate modem in bridge mode) for both elegance and also fewer devices to go wrong in the chain...so I am keen to know whether the Transcend module will do the job.

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post