SG-1100 Corrupted

LegsAJimbo

Hi All,

I have an out of warranty SG-1100 that I am having issues with.

When trying to 'run usbrecovery' it begins to boot, then loops through fsck maybe a dozen times before dropping back to the shell.

I have tried zeroing mmcsd0 (as below) to provide it with a clean disk, but still have the same problem.

# sysctl kern.geom.debugflags=0x10
kern.geom.debugflags: 0 -> 16
# dd if=/dev/zero of=/dev/mmcsd0 status=progress bs=128k
dd: /dev/mmcsd0: end of device
59649+0 records in
59648+0 records out
7818182656 bytes transferred in 363.891100 secs (21484952 bytes/sec)

I have tried a 2.4.5 USB image as well as a 22.01 image.

I'm thinking the eMMC may be dead, or flash/spi0 has something to do with the boot process and could be corrupted, however I don't dare try and wipe that!

Any help would be very much appreciated!

Boot log from a 'run usbrecovery' boot...

TIM-1.0
WTMI-armada-17.10.5-34ce216
WTMI: system early-init
SVC REV: 5, CPU VDD voltage: 1.248V

Fill memory before self refresh...done

Now in Self-refresh Mode
Exited self-refresh ...


Self refresh Pass.
DDR self test mode test done!!
Vref read training
===================
Final vdac_value 0x0000001F

Vref write training
===================
Final vref_value 0x0000001F

DLL TUNING
==============
   DLL 0xc0001050[21:16]: [3,36,1c]
   DLL 0xc0001050[29:24]: [5,2a,17]
   DLL 0xc0001054[21:16]: [7,35,1e]
   DLL 0xc0001054[29:24]: [9,32,1d]
   DLL 0xc0001074[21:16]: [0,3f,1f]
   DLL 0xc0001074NOTICE:  Booting Trusted Firmware
NOTICE:  BL1: v1.3(release):armada-17.10.8:34247e0
NOTICE:  BL1: Built : 16:19:41, Nov  1 2NOTICE:  BL2: v1.3(release):armada-17.10.8:34247e0
NOTICE:  BL2: Built : 16:19:45, Nov  1 20NOTICE:  BL31: v1.3(release):armada-17.10.8:34247e0
NOTICE:  BL31:

U-Boot 2017.03-armada-17.10.2-g6a6581a-dirty (Nov 01 2018 - 16:04:57 -0300)

Model: Marvell Armada 3720 Community Board ESPRESSOBin
       CPU    @ 1200 [MHz]
       L2     @ 800 [MHz]
       TClock @ 200 [MHz]
       DDR    @ 750 [MHz]
DRAM:  1 GiB
U-Boot DT blob at : 000000003f716298
Comphy-0: USB3          5 Gbps    
Comphy-1: PEX0          2.5 Gbps  
Comphy-2: SATA0         6 Gbps    
SATA link 0 timeout.
AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
flags: ncq led only pmp fbss pio slum part sxs 
PCIE-0: Link down
MMC:   sdhci@d0000: 0, sdhci@d8000: 1
SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB, total 4 MiB
Net:   eth0: neta@30000 [PRIME]
Hit any key to stop autoboot:  2  0 
Marvell>> run usbrecovery
switch to partitions #0, OK
mmc1(part 0) is current device

MMC erase: dev # 1, block # 0, count 4194304 ... 4194304 blocks erased: OK
starting USB...
USB0:   Register 2000104 NbrPorts 2
Starting the controller
USB XHCI 1.00
USB1:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning bus 1 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
reading efi/boot/bootaa64.efi
2097152 bytes read in 47 ms (42.6 MiB/s)
reading armada-3720-sg1100.dtb
12725 bytes read in 20 ms (621.1 KiB/s)
## Starting EFI application at 05000000 ...
Card did not respond to voltage select!
mmc_init: -95, time 41
Scanning disk sdhci@d8000.blk...
Scanning disk usb_mass_storage.lun0...
Found 8 disks
[?25h[2J

>> FreeBSD EFI boot block

   Loader path: /boot/loader.efi



   Initializing modules: ZFS UFS

   Load Path: bootefi

   Load Device: bootefi

   Probing 8 block devices...not supported

not supported

not supported

better

not supported

not supported

not supported

better

 done

    ZFS found no pools

    UFS found 2 partitions

    command args: -S115200



[?25h[18tConsoles: EFI console  


[?25h|/-\|/-\FreeBSD/arm64 EFI loader, Revision 1.1


(Thu Feb 13 14:48:37 EST 2020 root@buildbot3-nyi.netgate.com)





   Command line arguments: loader.efi -S115200


   EFI version: 2.05


   EFI Firmware: Das U-boot (rev 0.00)


   BootCurrent: 0000


   BootOrder: 532d 3131 3235 3030 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*]


Setting currdev to disk0p3:


|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/Loading /boot/defaults/loader.conf


-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|//boot/kernel/kernel text=0x9825b0 -\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-data=0x10ce970+0x3c7fa4 \|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|syms=[0x8+0x11f328/-\|/-\|/-+0x8+0xf63f3\|/-\|/]


-\|/-\|/-\|/


Hit [Enter] to boot immediately, or any other key for command prompt.



Booting [/boot/kernel/kernel] in 2 seconds... 
Booting [/boot/kernel/kernel] in 1 second... 
Booting [/boot/kernel/kernel]...               


Using DTB provided by EFI at 0x8000000.


-\|/Copyright (c) 1992-2020 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.3-STABLE #239 885b1ed26b6(factory-RELENG_2_4_5): Tue Jun  2 17:47:00 EDT 2020
    root@buildbot3-nyi.netgate.com:/build/factory-crossbuild-245-aarch64/obj/aarch64/Og10eFss/build/factory-crossbuild-245-aarch64/sources/FreeBSD-src/sys/pfSense arm64
FreeBSD clang version 8.0.1 (tags/RELEASE_801/final 366581) (based on LLVM 8.0.1)
VT: init without driver.
Starting CPU 1 (1)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffff0000001738b0, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffff00000017395c, 0) error 1
iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_bss_fw, 0xffff000000173a08, 0) error 1
iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_ibss_fw, 0xffff000000173ab4, 0) error 1
iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_monitor_fw, 0xffff000000173b60, 0) error 1
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xffff000000173804, 0) error 1
wlan: mac acl policy registered
random: entropy device external interface
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
simplebus1: <Flattened device tree simple bus> on simplebus0
pinctl0: <Armada 37x0 North Bridge pinctl Controller> mem 0x13800-0x138ff,0x13c00-0x13c1f on simplebus1
gpio0: <Armada 37x0 GPIO Controller> on pinctl0
gpiobus0: <OFW GPIO bus> on gpio0
pinctl1: <Armada 37x0 South Bridge pinctl Controller> mem 0x18800-0x188ff,0x18c00-0x18c1f on simplebus1
gpio1: <Armada 37x0 GPIO Controller> on pinctl1
gpiobus1: <OFW GPIO bus> on gpio1
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
gic0: <ARM Generic Interrupt Controller v3.0> mem 0x1d00000-0x1d0ffff,0x1d40000-0x1d7ffff,0x1d80000-0x1d81fff,0x1d90000-0x1d91fff,0x1da0000-0x1dbffff irq 27 on simplebus1
generic_timer0: <ARMv8 Generic Timer> irq 0,1,2,3 on ofwbus0
Timecounter "ARM MPCore Timecounter" frequency 12500000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 12500000 Hz quality 1000
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
cpu1: <Open Firmware CPU> on cpulist0
pmu0: <Performance Monitoring Unit> irq 4 on ofwbus0
spi0: <Armada 37x0 SPI controller> mem 0x10600-0x10fff irq 6 on simplebus1
iichb0: <Marvell Armada 37x0 IIC controller> mem 0x11000-0x11023 irq 7 on simplebus1
iicbus0: <OFW I2C bus> on iichb0
iic0: <I2C generic I/O> on iicbus0
uart0: <Marvell Armada 3700 UART> mem 0x12000-0x121ff irq 9,10,11 on simplebus1
uart0: console (115200,n,8,1)
gpioc0: <GPIO controller> on gpio0
gpioc1: <GPIO controller> on gpio1
mvneta0: <NETA controller> mem 0x30000-0x33fff irq 14 on simplebus1
mvneta0: version is 10
mvneta0: Ethernet address: f0:ad:4e:08:6e:b2
mdio0: <MDIO> on mvneta0
e6000sw0: <Marvell 88E6341> on mdio0
e6000sw0: multi-chip addressing mode (0x1)
e6000sw0: CPU port at 0
e6000sw0: fixed port at 0
e6000sw0: PHY at port 1
miibus0: <MII bus> on e6000sw0
e1000phy0: <Marvell 88E1000 Gigabit PHY> PHY 17 on miibus0
e1000phy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: PHY at port 2
miibus1: <MII bus> on e6000sw0
e1000phy1: <Marvell 88E1000 Gigabit PHY> PHY 18 on miibus1
e1000phy1:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: PHY at port 3
miibus2: <MII bus> on e6000sw0
e1000phy2: <Marvell 88E1000 Gigabit PHY> PHY 19 on miibus2
e1000phy2:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: switch is ready.
etherswitch0: <Switch controller> on e6000sw0
xhci0: <Marvell Integrated USB 3.0 controller> mem 0x58000-0x5bfff irq 16 on simplebus1
xhci0: 32 bytes context size, 32-bit DMA
usbus0 on xhci0
ehci0: <Marvell Integrated USB 2.0 controller> mem 0x5e000-0x5ffff irq 17 on simplebus1
usbus1: EHCI version 1.0
usbus1 on ehci0
sdhci_xenon0: <Armada Xenon SDHCI controller> mem 0xd0000-0xd02ff,0x1e808-0x1e80b irq 24 on simplebus1
mmc0: <MMC/SD bus> on sdhci_xenon0
sdhci_xenon1: <Armada Xenon SDHCI controller> mem 0xd8000-0xd82ff,0x17808-0x1780b irq 25 on simplebus1
mmc1: <MMC/SD bus> on sdhci_xenon1
ahci0: <AHCI SATA controller> mem 0xe0000-0xe1fff irq 26 on simplebus1
ahci0: AHCI v1.30 with 1 6Gbps ports, Port Multiplier supported with FBS
ahcich0: <AHCI channel> at channel 0 on ahci0
pcib0: <Marvell Armada 3700 PCIe Bus Controller> mem 0xd0070000-0xd008ffff irq 5 on simplebus0
pcib0: link never came up
pci0: <PCI bus> on pcib0
gpioled0: <GPIO LEDs> on ofwbus0
cryptosoft0: <software crypto>
Timecounters tick every 1.000 msec
mvneta0: link state changed to UP
spibus0: <OFW SPI bus> on spi0
mx25l0: <M25Pxx Flash Family> at cs 0 mode 0 on spibus0
mx25l0: device type mx25u3235f, size 4096K in 64 sectors of 64K, erase size 4K
e6000sw0port1: link state changed to DOWN
e6000sw0port2: link state changed to DOWN
e6000sw0port3: link state changed to DOWN
usbus0: 5.0Gbps Super Speed USB v3.0
usbus1: 480Mbps High Speed USB v2.0
ugen0.1: <Marvell XHCI root HUB> at usbus0
uhub0: <Marvell XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
ugen1.1: <Marvell EHCI root HUB> at usbus1
uhub1: <Marvell EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
mmc0: No compatible cards found on bus
uhub0: 2 ports with 2 removable, self powered
mmcsd0: 8GB <MMCHC SEM08G 3.10 SN B19728CC MFG 04/2017 by 69 0x0000> at mmc1 50.0MHz/8bit/65535-block
mmcsd0boot0: 2MB partion 1 at mmcsd0
mmcsd0boot1: 2MB partion 2 at mmcsd0
mmcsd0rpmb: 2MB partion 3 at mmcsd0
uhub1: 1 port with 1 removable, self powered
ugen0.2: <Kingston DataTraveler 3.0> at usbus0
umass0 on uhub0
umass0: <Kingston DataTraveler 3.0, class 0/0, rev 3.20/0.01, addr 1> on usbus0
Release APs
da0 at umass-sim0 bus 0 scbus1 target 0 lun 0
da0: CPU  0: ARM Cortex-A53 r0p4<Kingston DataTraveler 3.0 > Removable Direct Access SPC-4 SCSI device
 affinity:da0: Serial Number E0D55E6B6472F4A1391490A8
  0da0: 400.000MB/s transfers

 Instruction Set Attributes 0 = <da0: 29510MB (60437492 512 byte sectors)
AES+PMULLda0: quirks=0x2<NO_6_BYTE>
,SHA1,SHA2,CRC32>
 Instruction Set Attributes 1 = <>
         Processor Features 0 = <GIC,AdvSIMD,Float,EL3 32,EL2 32,EL1 32,EL0 32>
         Processor Features 1 = <0>
      Memory Model Features 0 = <4k Granule,64k Granule,MixedEndian,S/NS Mem,16bit ASID,1TB PA>
      Memory Model Features 1 = <>
      Memory Model Features 2 = <32b CCIDX,48b VA>
             Debug Features 0 = <2 CTX Breakpoints,4 Watchpoints,6 Breakpoints,PMUv3,Debug v8>
             Debug Features 1 = <0>
         Auxiliary Features 0 = <0>
         Auxiliary Features 1 = <0>
CPU  1: ARM Cortex-A53 r0p4 affinity:  1
Trying to mount root from ufs:/dev/diskid/DISK-B19728CCs3 [rw,noatime]...
WARNING: / was not properly dismounted
WARNING: /: mount pending error: blocks 96 files 4
Warning: no time-of-day clock registered, system time will not be set accurately
Configuring crash dumps...
No suitable dump device was found.
** SU+J Recovering /dev/diskid/DISK-B19728CCs3
** Reading 11730944 byte journal from inode 4.
** Building recovery table.
** Resolving unreferenced inode list.
** Processing journal entries.
** 1174 journal records in 150016 bytes for 25.04% utilization
** Freed 7 inodes (0 dirs) 2 blocks, and 16 frags.

***** FILE SYSTEM MARKED CLEAN *****
WARNING: /: reload pending error: blocks 96 files 4
Filesystems are clean, continuing...
Mounting filesystems...
** /dev/diskid/DISK-B19728CCs3
** SU+J Recovering /dev/diskid/DISK-B19728CCs3

USE JOURNAL? yes

** Reading 11730944 byte journal from inode 4.

RECOVER? yes

** Building recovery table.
** Resolving unreferenced inode list.
** Processing journal entries.

WRITE CHANGES? yes

** 1174 journal records in 150016 bytes for 25.04% utilization
** Freed 7 inodes (0 dirs) 2 blocks, and 16 frags.

***** FILE SYSTEM MARKED CLEAN *****
WARNING: /: reload pending error: blocks 96 files 4
** /dev/diskid/DISK-B19728CCs3
** SU+J Recovering /dev/diskid/DISK-B19728CCs3

USE JOURNAL? yes

** Reading 11730944 byte journal from inode 4.

RECOVER? yes

** Building recovery table.
** Resolving unreferenced inode list.
** Processing journal entries.

WRITE CHANGES? yes

** 1174 journal records in 150016 bytes for 25.04% utilization
** Freed 7 inodes (0 dirs) 2 blocks, and 16 frags.

***** FILE SYSTEM MARKED CLEAN *****
WARNING: /: reload pending error: blocks 96 files 4
** /dev/diskid/DISK-B19728CCs3
** SU+J Recovering /dev/diskid/DISK-B19728CCs3

USE JOURNAL? yes

** Reading 11730944 byte journal from inode 4.

RECOVER? yes

** Building recovery table.
** Resolving unreferenced inode list.
** Processing journal entries.

WRITE CHANGES? yes

** 1174 journal records in 150016 bytes for 25.04% utilization
** Freed 7 inodes (0 dirs) 2 blocks, and 16 frags.

***** FILE SYSTEM MARKED CLEAN *****
WARNING: /: reload pending error: blocks 96 files 4
** /dev/diskid/DISK-B19728CCs3
** SU+J Recovering /dev/diskid/DISK-B19728CCs3

USE JOURNAL? yes

** Reading 11730944 byte journal from inode 4.

RECOVER? yes

** Building recovery table.
** Resolving unreferenced inode list.
** Processing journal entries.

WRITE CHANGES? yes

** 1174 journal records in 150016 bytes for 25.04% utilization
** Freed 7 inodes (0 dirs) 2 blocks, and 16 frags.

***** FILE SYSTEM MARKED CLEAN *****
WARNING: /: reload pending error: blocks 96 files 4
** /dev/diskid/DISK-B19728CCs3
** SU+J Recovering /dev/diskid/DISK-B19728CCs3

USE JOURNAL? yes

** Reading 11730944 byte journal from inode 4.

RECOVER? yes

** Building recovery table.
** Resolving unreferenced inode list.
** Processing journal entries.

WRITE CHANGES? yes

** 1174 journal records in 150016 bytes for 25.04% utilization
** Freed 7 inodes (0 dirs) 2 blocks, and 16 frags.

***** FILE SYSTEM MARKED CLEAN *****
WARNING: /: reload pending error: blocks 96 files 4
** /dev/diskid/DISK-B19728CCs3
** SU+J Recovering /dev/diskid/DISK-B19728CCs3

USE JOURNAL? yes

** Reading 11730944 byte journal from inode 4.

RECOVER? yes

** Building recovery table.
** Resolving unreferenced inode list.
** Processing journal entries.

WRITE CHANGES? yes

** 1174 journal records in 150016 bytes for 25.04% utilization
** Freed 7 inodes (0 dirs) 2 blocks, and 16 frags.

***** FILE SYSTEM MARKED CLEAN *****
WARNING: /: reload pending error: blocks 96 files 4
** /dev/diskid/DISK-B19728CCs3
** SU+J Recovering /dev/diskid/DISK-B19728CCs3

USE JOURNAL? yes

** Reading 11730944 byte journal from inode 4.

RECOVER? yes

** Building recovery table.
** Resolving unreferenced inode list.
** Processing journal entries.

WRITE CHANGES? yes

** 1174 journal records in 150016 bytes for 25.04% utilization
** Freed 7 inodes (0 dirs) 2 blocks, and 16 frags.

***** FILE SYSTEM MARKED CLEAN *****
WARNING: /: reload pending error: blocks 96 files 4
** /dev/diskid/DISK-B19728CCs3
** SU+J Recovering /dev/diskid/DISK-B19728CCs3

USE JOURNAL? yes

** Reading 11730944 byte journal from inode 4.

RECOVER? yes

** Building recovery table.
** Resolving unreferenced inode list.
** Processing journal entries.

WRITE CHANGES? yes

** 1174 journal records in 150016 bytes for 25.04% utilization
** Freed 7 inodes (0 dirs) 2 blocks, and 16 frags.

***** FILE SYSTEM MARKED CLEAN *****
WARNING: /: reload pending error: blocks 96 files 4
** /dev/diskid/DISK-B19728CCs3
** SU+J Recovering /dev/diskid/DISK-B19728CCs3

USE JOURNAL? yes

** Reading 11730944 byte journal from inode 4.

RECOVER? yes

** Building recovery table.
** Resolving unreferenced inode list.
** Processing journal entries.

WRITE CHANGES? yes

** 1174 journal records in 150016 bytes for 25.04% utilization
** Freed 7 inodes (0 dirs) 2 blocks, and 16 frags.

***** FILE SYSTEM MARKED CLEAN *****
WARNING: /: reload pending error: blocks 96 files 4
** /dev/diskid/DISK-B19728CCs3
** SU+J Recovering /dev/diskid/DISK-B19728CCs3

USE JOURNAL? yes

** Reading 11730944 byte journal from inode 4.

RECOVER? yes

** Building recovery table.
** Resolving unreferenced inode list.
** Processing journal entries.

WRITE CHANGES? yes

** 1174 journal records in 150016 bytes for 25.04% utilization
** Freed 7 inodes (0 dirs) 2 blocks, and 16 frags.

***** FILE SYSTEM MARKED CLEAN *****
WARNING: /: reload pending error: blocks 96 files 4
ERROR: Impossible to mount filesystem, use interactive shell to attempt to recover it
#

stephenw10

Mmm, that does look like it has failed to erase the eMMC which can indicate it has failed.

Have you opened a TAC ticket to review it?

Steve

LegsAJimbo

Hi @stephenw10

Thanks for getting back! The unit is out of warranty so I felt that would be a bit cheeky.

stephenw10

If it's a hardware or install/recovery issue then we can help you there. They can at least review the full logs.

LegsAJimbo

@stephenw10

That's great service thanks! I've opened a ticket, I'll update this post once resolved in case it's a fix that might help others.

Thanks again!