Strange Gateway Issues with 2.7.0 development builds

townsenk64

@stephenw10
Thank you! I've submitted a bug report.

townsenk64

@stephenw10 FYI, Discovered a workaround for this issue. Enabling the "Do not add Static Routes" in the Gateway monitoring options in System/Advanced/Miscellaneous allows both gateways to come up properly.

marcosm

Relevant routes:

Destination        Gateway            Flags     Netif Expire
default            70.188.246.1       UGS         em0
10.10.0.0/16       10.10.0.1          UGS      ovpnc2
10.10.0.1          link#11            UH       ovpnc2
10.10.0.3          link#11            UHS         lo0
10.11.0.0/16       10.11.0.1          UGS      ovpnc1
10.11.0.1          link#10            UH       ovpnc1
10.11.0.4          link#10            UHS         lo0
141.98.254.71      10.10.0.3          UHS      ovpnc2
141.136.106.30     10.11.0.4          UHS      ovpnc1

The commands show the following states:

all icmp 10.11.0.4:24803 (10.11.0.4:27133) -> 141.136.106.30:24803       0:0
   age 00:02:41, expires in 00:00:09, 313:313 pkts, 9077:9077 bytes, rule 47
   id: 86a05e6300000000 creatorid: a7a94773 gateway: 10.11.0.4
   origif: ovpnc1
all icmp 10.0.8.1:56301 (10.10.0.3:27587) -> 141.98.254.71:56301       0:0
   age 00:02:41, expires in 00:00:09, 313:0 pkts, 9077:0 bytes, rule 45
   id: 88a05e6300000000 creatorid: a7a94773 gateway: 0.0.0.0
   origif: ovpnc2

... which are created from these rules:

@45 pass out inet all flags S/SA keep state allow-opts label "let out anything IPv4 from firewall host itself" ridentifier 1000009913
  [ Evaluations: 11668     Packets: 13437     Bytes: 2665431     States: 146   ]
  [ Inserted: uid 0 pid 9864 State Creations: 765   ]
  [ Last Active Time: Sun Oct 30 10:51:37 2022 ]
@47 pass out route-to (ovpnc1 10.11.0.4) inet from 10.11.0.4 to ! 10.11.0.0/16 flags S/SA keep state allow-opts label "let out anything from firewall host itself" ridentifier 1000010012
  [ Evaluations: 3401      Packets: 16        Bytes: 464         States: 0     ]
  [ Inserted: uid 0 pid 9864 State Creations: 0     ]
  [ Last Active Time: N/A ]

The first rule @45 shows that the traffic is passing via a rule without route-to set which could mean the traffic actually went out a different interface even though origif shows ovpnc1 (due to some pf quirks I don't recall). The second rule @47 is concerning since I'd expect that to be the gateway 10.11.0.1 rather than pfSense's interface. See the warning here: https://docs.netgate.com/pfsense/en/latest/vpn/openvpn/configure-server-tunnel.html#ipv4-ipv6-local-network-s

Try comparing the states between the broken and working conditions.

townsenk64

@marcosm Thank you for your detailed analysis but I simply don't understand all of this at the same level as you do. I suppose I will wait and see if a developer eventually has the same issue so it will be recognized. Enabling the "Do not add Static Routes" options keeps things working at least. I often hear that it's a "configuration issue" and not an issue with Pfsense. How is that when the configuration never changed? The Pfsense code is what is being changed and this is completely expected in a developement environmant.

marcosm

OK. At least for now, it would be helpful if you could provide the same logs/info while it's working so it can be compared.

FWIW this is what I have on my working setup after restarting the OpenVPN service:

all icmp 172.27.114.137:38623 -> 172.27.114.129:38623       0:0
   age 00:51:56, expires in 00:00:10, 6012:6007 pkts, 174348:174203 bytes, rule 143
   id: 28aa696300000000 creatorid: 4da82510 gateway: 0.0.0.0
   origif: ovpnc2
all icmp 172.17.5.2:38750 -> 172.17.5.1:38750       0:0
   age 00:51:56, expires in 00:00:10, 6013:6007 pkts, 174377:174203 bytes, rule 143
   id: 29aa696300000000 creatorid: 4da82510 gateway: 0.0.0.0
   origif: ovpnc3

@143 pass out inet all flags S/SA keep state allow-opts label "let out anything IPv4 from firewall host itself" ridentifier 1000016215
  [ Evaluations: 59832     Packets: 171879    Bytes: 57085442    States: 266   ]
  [ Inserted: uid 0 pid 86586 State Creations: 967   ]
  [ Last Active Time: Mon Nov  7 12:35:47 2022 ]

And sometime after reboot:

all icmp 172.27.114.137:61325 -> 172.27.114.129:61325       0:0
   age 01:24:27, expires in 00:00:09, 9817:9811 pkts, 284693:284519 bytes, rule 140
   id: 0e55696300000000 creatorid: 4da82510 gateway: 0.0.0.0
   origif: ovpnc2
all icmp 172.17.5.2:61695 -> 172.17.5.1:61695       0:0
   age 01:25:36, expires in 00:00:10, 9949:9940 pkts, 288521:288260 bytes, rule 140
   id: 0f55696300000000 creatorid: 4da82510 gateway: 0.0.0.0
   origif: ovpnc3

@140 pass out on lo0 inet all flags S/SA keep state label "pass IPv4 loopback" ridentifier 1000016212
  [ Evaluations: 22311     Packets: 0         Bytes: 0           States: 0     ]
  [ Inserted: uid 0 pid 80759 State Creations: 0     ]
  [ Last Active Time: N/A ]

I'm not sure why it used @140 this time but it worked regardless. The differences here are I keep the monitoring IP as the tunnel gateway, and bind the service to localhost. I did test with it bound to the WAN interface itself and that was fine as well.

townsenk64

@marcosm Here are the outputs of the previously requested commands while my system is in a working state (with the static route disable option applied)

pfctl_vvss.txt netstat_rn4.txt pfctl_vvsr.txt

Could this be some strangeness with my VPN provider?

marcosm

The difference there is that the monitoring traffic is going out of the WAN instead of over the tunnel, hence it won't actually be useful in determining the status of the tunnel. I recommend keeping the monitoring IP as the tunnel gateway.

townsenk64

@marcosm I agree, Using the gateway static route option doesn't effectively monitor the tunnel but I have no choice if a want to continue testing, it doesn't work otherwise. Since this issue currently only appears to affect myself in the entire Pfsense testing community It will probably be dismissed until the next release when more people will be exposed to the problem and hopefully it will be addressed at that point.

townsenk64

@marcosm It appears that this issue has been around to some degree for the better part of 3 years https://www.reddit.com/r/PFSENSE/comments/eznfsa/psa_gateway_group_vpn_interfaces_fail_on_reboot/ It's possible dpinger may be starting before the OpenVPn clients can initialize. That's my guess anyway. It's not worth my time to try and submit a bug report on this so I will just post my workaround.
I installed the cron package and created this long sloppy entry to restart dpinger and the open vpn clients when the machine is rebooted. The delays increase my boot time significantly but it appears to at least allow my vpn clients to connect. I still need to determine if it's routing the client pings out the proper interfaces for gateway monitoring.

sleep 7 && /usr/local/sbin/pfSsh.php playback svc restart dpinger && sleep 7 && /usr/local/sbin/pfSsh.php playback svc restart openvpn client 1 && sleep 7 && /usr/local/sbin/pfSsh.php playback svc restart openvpn client 2

marcosm

I'm glad you were able to find a workaround! As mentioned, it looks like the gateway being assigned to the interface is the pfSense interface address itself; this is likely related to the issue, if not the cause, and is the result of incorrect configuration.

townsenk64

@marcosm Again, Your indicating that there is a configuration problem. The same configuration that has worked for 5 years prior to version 2.70. Just because you look at logs and see packets going out the wrong gateway does not necessarily mean my configuration told them to do so.