Plugging SFP transceiver from AT&T box directly into SG-2100
-
@dominikhoffmann They are, but for new deployments they use FTTH including their RDOF (Rural Digital Opportunity Fund) deployments. In some areas it will start out as RFoG in other areas they are using EPON. RFoG areas will eventually be upgraded to full EPON. EPON they will give you the Spectrum SONU unit, which is an EPON ONT with a 10G Ethernet port. Upload will be limited to 500Mbps until they change their minds on that.
-
@gtaxl I’m using the before mentioned fs.com ONT SFP pluggable in my SG-2100 i france, and it works like a charm. That ONT, can link at both 1Gbe and 2.5Gbe at the SFP side - and it works automatically at 1Gbe in the SG-2100 (which is 1Gbe only).
I have actually tried a wide range of different SFP’s in my SG-2100 (and SG-6100), and both are quite forgiving. Almost anything that can link at 1Gbe will work in them.
However, the SG-6100 does not allow 2.5Gbe SFP link speeds - seems it SFP 1Gbe/SFP+ 10Gbe link only.
Also: it does not like SFP/SFP+ to RJ45 pluggables unless they still emulate being a SX/LX Tranciever. -
@keyser Got the Ubiquiti UF-GP-B+ which should be 2.5G speed. Was working in my 6100. Couldn't provision it by my ISP because I can't access the module to find out it's modem ID that my ISP needs.
-
@mrsunfire Good to know, but I assume it was set to 1Gbe on the pfSense side, or was this actually a unit that could link @ 2.5Gbit?
-
@keyser It's by default on 1G I think. But it's a OLT not a ONT so it's useless. I go for the FS.com module.
-
@gtaxl: I have a couple of pictures of the module now. There was no time to mess with plugging it into the SG-2100 directly.
Here are the pictures:
The unit is a Nokia XGS-PON I-temp 1270 TX. I am trying to find specs on it, but haven’t had much luck. One of Nokia’s white papers says that an XGS-PON is a “10-gigabit-capable symmetric passive optical network.”
So, is the AT&T fiber coming in pulsing at 10 Gbit/s, but throughput is throttled at the CO or somewhere else, or is that module compatible with multiples speeds.
-
@dominikhoffmann yeah that's 10Gbps, won't work with the SG-2100. Cool to know what module it is though.
-
@gtaxl: What’s your explanation for why it won’t? Is it that the electronic interface’s timing specs don’t match?
Could I use a different, compatible SFP transceiver, instead, and make it work with AT&T’s 10 Gbit/s fiber? My guess is that, if so, I would have problems getting the transceiver provisioned by AT&T.
-
@dominikhoffmann You'll need an SFP+ port to use that. The 2100 is a 1G SFP only.
-
@dominikhoffmann My understanding is if you have an older ONT then it is 1Gb on the fiber, if you have the newer service that can go above 1Gb then it is 10Gb throttled at the CO.
-
@andyrh If you have an XGS-PON it's 10G.
XG = roman numeral 10Gig
S=Symetrical
PON = Passive Optical Network -
@jarhead Mine is a 6 or 7 year old ONT screwed to the wall. I am certain it is 1Gb. My area was one of the first to get fiber in the city, and I was quick to sign up.
-
@andyrh I'm not doubting that. Just telling you the nomenclature.
You probably have a GPON. -
I haven't read through all of the replies, but you cannot eliminate the AT&T gateway. First off, the newer models like the one shown have the ONT built-in. Secondly, the fiber service requires certificate-based authentication, so even if you clone the AT&T gateway's MAC address on your pfSense it will not work.
The previous workarounds also do not work like they did with previous AT&T gateways and separate ONT module. If you want any fiber plan over 1 gig, then you will be issued the same gateway as in the original post. Also note the LAN ports are all 1 gig with the exception of first port which is blue and will support 5 gig, 2.5 gig, or 1 gig.
