23.01.b.20230106.0600 IGMP proxy stops TV stream

thebear

@lnguyen said in 23.01.b.20230106.0600 IGMP proxy stops TV stream:

@thebear There are reports that the Intel i226-V has issues like the 1st revision of the Intel i225-V. From what I recall, it was only fully resolved with a hardware fix with Revision 3.

https://linustechtips.com/topic/1483003-raptor-lake-motherboards-allegedly-hit-with-ethernet-controller-flaw-intel-i226-v-25gbe-has-a-connection-drop-issue-no-fix-currently/

Yeah saw that, but where is the truth and facts? All the website are copying the news and spreading rumors last week, clickbaits. My pfSense unit with 22.5 never had a single disconnect, stable as a rock.

And now only igmp joins are not received by the proxy. Which could be some kernel igmp snooping for example -> software ;-)

I'm not believing the news sites as my unicast internet is stable as a rock with 23.01 and the i-226v. Its more clickbaite news ;-)

Nevertheless, thanks for sharing, all pieces could help.

Nothing going on- > Link logs over the last uptime arround 3,5 day:

2023-01-22 08:49:16.956753+01:00	php-fpm	363	/rc.newwanip: rc.newwanip: Info: starting on igc1.4.
2023-01-22 08:49:15.952055+01:00	check_reload_status	401	rc.newwanip starting igc1.4
2023-01-22 08:49:14.525924+01:00	check_reload_status	401	Linkup starting igc1.6
2023-01-22 08:49:14.520114+01:00	check_reload_status	401	Linkup starting igc1.4
2023-01-22 08:49:14.514628+01:00	kernel	-	igc1.6: link state changed to UP
2023-01-22 08:49:14.514596+01:00	kernel	-	igc1.4: link state changed to UP
2023-01-22 08:49:14.514537+01:00	kernel	-	igc1: link state changed to UP
2023-01-22 08:49:14.514245+01:00	check_reload_status	401	Linkup starting igc1
2023-01-22 08:48:59.918274+01:00	check_reload_status	401	Linkup starting igc1.6
2023-01-22 08:48:59.916272+01:00	check_reload_status	401	Linkup starting igc1.4

stephenw10

Yeah this seems very unlikely to be hardware given it was working fine in 22.05.

I could believe the updated driver is doing something to mangle the igmp packets though.

Check the enabled options in the NIC with ifconfig -vvvm igc0. Perhaps it's not correctly disabling checksum offload. Or maybe some new option is present in 23.01 that wasn't in 22.05 at all.

For example the 8200 i226 NICs:

[22.05.1-RELEASE][root@8200-2.stevew.lan]/root: pciconf -lv igc0
igc0@pci0:4:0:0:        class=0x020000 card=0x00008086 chip=0x125c8086 rev=0x04 hdr=0x00
    vendor     = 'Intel Corporation'
    class      = network
    subclass   = ethernet
[22.05.1-RELEASE][root@8200-2.stevew.lan]/root: ifconfig -vvvm igc0
igc0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=e120bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_MAGIC,VLAN_HWFILTER,RXCSUM_IPV6,TXCSUM_IPV6>
        capabilities=f53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,NETMAP,RXCSUM_IPV6,TXCSUM_IPV6>
        ether 90:ec:77:47:5c:e8
        inet6 fe80::92ec:77ff:fe47:5ce8%igc0 prefixlen 64 scopeid 0x1
        inet6 fe80::1:1%igc0 prefixlen 64 scopeid 0x1
        inet 192.168.92.1 netmask 0xffffff00 broadcast 192.168.92.255
        media: Ethernet autoselect
        status: no carrier
        supported media:
                media autoselect
                media 2500Base-T
                media 1000baseT
                media 1000baseT mediaopt full-duplex
                media 100baseTX mediaopt full-duplex
                media 100baseTX
                media 10baseT/UTP mediaopt full-duplex
                media 10baseT/UTP
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>

Steve

thebear

@stephenw10 said in 23.01.b.20230106.0600 IGMP proxy stops TV stream:

Yeah this seems very unlikely to be hardware given it was working fine in 22.05.

I could believe the updated driver is doing something to mangle the igmp packets though.

Check the enabled options in the NIC with ifconfig -vvvm igc0. Perhaps it's not correctly disabling checksum offload. Or maybe some new option is present in 23.01 that wasn't in 22.05 at all.

Morning @stephenw10 below the output and some screenshots from a diff tool. They do diff, could you see some issues?

[23.01-BETA][admin@pfSense.high.local]/root: pciconf -lv igc0
igc0@pci0:2:0:0:        class=0x020000 rev=0x04 hdr=0x00 vendor=0x8086 device=0x125c subvendor=0x8086 subdevice=0x0000
    vendor     = 'Intel Corporation'
    class      = network
    subclass   = ethernet
[23.01-BETA][admin@pfSense.high.local]/root: ifconfig -vvvm igc0
igc0: flags=8863<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
        description: Server
        options=48020b8<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_MAGIC,NOMAP>
        capabilities=4f43fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWTSO,NETMAP,RXCSUM_IPV6,TXCSUM_IPV6,NOMAP>
        ether 7c:2b:e1:13:7a:db
        inet6 fe80::7e2b:e1ff:fe13:7adb%igc0 prefixlen 64 scopeid 0x1
        inet6 fe80::1:1%igc0 prefixlen 64 scopeid 0x1
        inet6 2a02:a<bla> prefixlen 64
        inet 172.16.1.1 netmask 0xffffff00 broadcast 172.16.1.255
        media: Ethernet autoselect (1000baseT <full-duplex>)
        status: active
        supported media:
                media autoselect
                media 2500Base-T
                media 1000baseT
                media 1000baseT mediaopt full-duplex
                media 100baseTX mediaopt full-duplex
                media 100baseTX
                media 10baseT/UTP mediaopt full-duplex
                media 10baseT/UTP
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
[23.01-BETA][admin@pfSense.high.local]/root:

stephenw10

Ok, so we can see that, interestingly, the VLAN hardware filtering capability has been removed. And it was previously in use but I don't think you are using VLANs?

The NOMAP (unmapped mbufs) capability has been added and is enabled by default. I don't believe that would affect only multicast traffic. And it appears to be a transmit option.

Are you able to test using a different interface?

thebear

@stephenw10 said in 23.01.b.20230106.0600 IGMP proxy stops TV stream:

Ok, so we can see that, interestingly, the VLAN hardware filtering capability has been removed. And it was previously in use but I don't think you are using VLANs?

The NOMAP (unmapped mbufs) capability has been added and is enabled by default. I don't believe that would affect only multicast traffic. And it appears to be a transmit option.

Are you able to test using a different interface?

The diff had made against YOUR output let me clarify that ;-) Yes using a hand-full VLAN's on LAN and two on WAN.

Would you be able to elaborate more on the NOMAP?

Do you mean another interface on the same board, like from igc0 to igc2? Or put in another interface board, the last option is impossible as it is a fixed housing+NIC's.

thebear

The thing is that its not quite easy to rollback tot 22.05 to test the previous interface output or IGMP packet capture.

stephenw10

The nomap capability should be easy to disable but it appears ifconfig may not have caught up yet. I can't find a syntax that works. But I doubt that would make any difference here.

I also compared the options between 22.05 and 23.01 from the same config in the 8200 and saw the same.

If it's a ZFS install you should be ble to roll back the BE snapshot.

thebear

@stephenw10 23.01.r.20230202.0019 same results with the RC build ;(

thebear

@stephenw10 could this IGMP issue be added to the list of issues?https://redmine.pfsense.org/projects/pfsense/issues?query_id=186

stephenw10

If an IGMPproxy bug report can be opened then it can be added to that list.

Were you able to confirm that the queries from the proxy are generated with a correct checksum in 22.05?

If so I'd go ahead and open a bug report for it.

Do you see the bad checksum on all IGMP packets generated by the proxy? Upstream and downstream?

thebear

@stephenw10 said in 23.01.b.20230106.0600 IGMP proxy stops TV stream:

If an IGMPproxy bug report can be opened then it can be added to that list.

Were you able to confirm that the queries from the proxy are generated with a correct checksum in 22.05?

If so I'd go ahead and open a bug report for it.

Do you see the bad checksum on all IGMP packets generated by the proxy? Upstream and downstream?

Hi steve, the thing is that the config is changing a lot. My 22.05 backup is too old. And the 226v NIC is not supported yet so a fresh 22.05 installation is consuming quite a lot time.

My action plan:
-fresh install of final 23.01 usb installer image. Test with just a clean install, configure the IPTV_WAN/LAN and IGMP.
-If that works, load the backup file, check again.
-If both not work I'll install 2.7 and try to upgrade to 22.05, well in fact that's a downgrade. My only option left is a fresh install with an USB NIC from 2.6.0?

I'll capture the WAN traffic to check the checksum.

stephenw10

You don't have a 22.05 ZFS BE snapshot you can roll back to?

thebear

@stephenw10 said in 23.01.b.20230106.0600 IGMP proxy stops TV stream:

You don't have a 22.05 ZFS BE snapshot you can roll back to?

You mentioned that before. I got not clue how to do that. Tested some CLI commands, never found the power to press enter.

If there is some more explanation or a how to documented?

EDIT: BE seems to be Boot Environment? Interesting, I was on the wrong path with the CLI commands.

stephenw10

Well you can do it from the CLI using bectl but it's much easier using the GUI.

See: https://docs.netgate.com/pfsense/en/latest/backup/zfsbe/gui.html

Also note that you cannot roll back to a 22.01 snapshot BE. It will fail to boot. The compatibility was added in 22.05.

thebear

@stephenw10 its definitely an 23.01 bug, reverted to 22.05 and not a glitch in the TV. And the corrupt IGMP packet is gone, and therefore the STB is answering in 22.05. Due to the corrupt IGMP report listeners request the STB does not answer back in 23.01 and TV stops playing.

How does filing a bug works?

22.05 full set of requests + answers from the STB + valid packet

23.01 full set of request and missing answers from the STB + corrupt packet shows up.

stephenw10

Bug looks good, thanks.

https://redmine.pfsense.org/issues/13929

Remie2000

Hi I just came accross this same issue. And this is a blocking issue for me aswell.
I hope it can be fixed in 23.01 instead of 23.05 where it is scheduled for right now.

DBMandrake

@stephenw10

Just to report that I also seem to be having an issue with the IGMP Proxy generating packets with invalid checksums, although in my case I am running 2.6.0, and I am using a completely different network adaptor.

As I am only just configuring the IGMP proxy for the first time (after the router has been installed for a few months) I do not have a previously working installation to compare with, and I have been troubleshooting for some time before noticing the checksum errors. Tcpdump running on the same device shows:

tcpdump: listening on ix0, link-type EN10MB (Ethernet), capture size 262144 bytes
11:21:25.462732 IP (tos 0xc0, ttl 1, id 13, offset 0, flags [none], proto IGMP (2), length 32, options (RA))
    10.0.2.3 > 224.0.0.1: igmp query v2
11:21:26.999364 IP (tos 0x0, ttl 1, id 58030, offset 0, flags [none], proto IGMP (2), length 32, options (RA), bad cksum 0 (->5624)!)
    10.0.1.254 > 224.0.0.7: igmp v2 report 224.0.0.7
11:21:27.601357 IP (tos 0x0, ttl 1, id 35790, offset 0, flags [none], proto IGMP (2), length 32, options (RA), bad cksum 0 (->ac0f)!)
    10.0.1.254 > 224.0.0.252: igmp v2 report 224.0.0.252
11:21:30.205921 IP (tos 0x0, ttl 1, id 33675, offset 0, flags [none], proto IGMP (2), length 32, options (RA), bad cksum 0 (->b453)!)
    10.0.1.254 > 224.0.0.251: igmp v2 report 224.0.0.251
11:21:36.336285 IP (tos 0x0, ttl 1, id 37154, offset 0, flags [none], proto IGMP (2), length 32, options (RA), bad cksum 0 (->a5fc)!)
    10.0.1.254 > 224.0.1.187: igmp v2 report 224.0.1.187
11:21:36.672559 IP (tos 0x0, ttl 1, id 59654, offset 0, flags [none], proto IGMP (2), length 32, options (RA), bad cksum 0 (->3fd9)!)
    10.0.1.254 > 239.255.255.250: igmp v2 report 239.255.255.250

Tcpdump running on another PFSense router connected to the same switch does not show these packets at all so presumably they are being dropped by the switch or receiving router due to the checksum error. In any case Multicast routing between VLAN's is not working.

Here is the network card configuration:

pciconf -lv ix0

ix0@pci0:1:0:0: class=0x020000 card=0x031b1dcf chip=0x15288086 rev=0x01 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = 'Ethernet Controller 10-Gigabit X540-AT2'
    class      = network
    subclass   = ethernet


ifconfig -vvvm ix0

ix0: flags=8b43<UP,BROADCAST,RUNNING,PROMISC,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
        description: LAN
        options=e138bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,RXCSUM_IPV6,TXCSUM_IPV6>
        capabilities=f53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,NETMAP,RXCSUM_IPV6,TXCSUM_IPV6>
        ether 98:b7:85:89:7f:74
        inet6 fe80::9ab7:85ff:fe89:7f74%ix0 prefixlen 64 scopeid 0x1
        inet 10.0.1.254 netmask 0xffff0000 broadcast 10.0.255.255
        media: Ethernet autoselect (10Gbase-T <full-duplex>)
        status: active
        supported media:
                media autoselect
                media 100baseTX
                media 1000baseT
                media 10Gbase-T
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>

I have not yet tried disabling Hardware Checksum Offloading as I've only just discovered this thread now in the middle of a work day so I can't reboot just now but I could try rebooting in the evening if this might provide a useable workaround.

The hardware is a Quad core 3.5Ghz Xeon server so should be OK to do software based checksum generation I would think ?

thebear

@dbmandrake I think a reboot should be done. With the setting enable this could be a valid data capture. Without the offloading pfSense is able to generate the checksums itself.

We can’t make a conclusion without disabling offloading.

DBMandrake

@thebear Yes I will disable checksum offloading and reboot after hours and test again tomorrow.

Also unless I have missed something, PFSense is still sending out igmp v2 reports with corrupt checksums even after I have disabled the IGMP proxy service ?

Such as:

12:29:38.863070 IP (tos 0x0, ttl 1, id 33267, offset 0, flags [none], proto IGMP (2), length 32, options (RA), bad cksum 0 (->b5eb)!)
    10.0.1.254 > 224.0.0.251: igmp v2 report 224.0.0.251

Could this be related to the Avahi service (which is still running) since 224.0.0.251 is the multicast address used by mDNS ? If so what is generating the igmp report ? The Avahi service itself or something within a lower level in the OS ?