23.1 using more RAM

jimp

@jimp said in 23.1 using more RAM:

their wired usage is high but drops immediately when the system needs active memory.

I think this is part of the problem to be honest - users hate to see all their memory being used for whatever reason ;) Even if something is using it because nothing else is needing any memory and if that something needs it will be freed up for that something.

Just memory use showing high seems to trigger something is wrong in the users perspective.

Right, "Free RAM is wasted RAM" and all, but some people are implying that it isn't giving up the memory on their systems or it's causing other problems such as interfering with traffic, but it's not clear if there is a direct causal link here yet. But if we can reduce/eliminate the impact of ARC as a potential cause it will at least help narrow down what those others issues might be.

johnpoz

@jimp all true..

X doesn't work - oh my memory use is showing 90% that must be it.. When that most likely has nothing to do with X.. But sure if you can reduce it so memory is only showing 10% used and still have X then more likely to look deeper to that is actually causing their X issue.

edit:
Just an attempt to put it another way, not trying to mansplain it to you hehehe ;) ROFL..

FSC830

OMG... you mean...
the memory is sucked by extra terrestrials?
Or why do you refer to the X-files?

SCNR

Regards

pmagid

@fsc830 Maybe they have balloons....

DefenderLLC

The facts are something changed on my 6100 MAX between 22.05 and 23.01 that has essentially doubled my memory utilization at 3AM and never returns to normal without a reboot only to repeat itself again at 3AM.

Is it causing me a problem today? No, but it does bother me when I go from 18% to almost 40% for no apparent reason. This is clearly happening on other Netgate appliances too. Thanks, guys.

jimp

Right but we still don't know if you have a problem or the perception of a problem. It's almost certainly the latter.

It looks like on 22.05 those periodic jobs were all entirely disabled but it's not clear where that change got lost, since the file hasn't changed upstream.

For now you can edit /etc/crontab and remove the periodic lines or comment them out -- do not touch the rc.periodic lines as those are OK.

Before:

# Perform daily/weekly/monthly maintenance.
1	3	*	*	*	root	periodic daily
15	4	*	*	6	root	periodic weekly
30	5	1	*	*	root	periodic monthly

After

# Perform daily/weekly/monthly maintenance.
#1	3	*	*	*	root	periodic daily
#15	4	*	*	6	root	periodic weekly
#30	5	1	*	*	root	periodic monthly

DefenderLLC

@jimp said in 23.1 using more RAM:

/etc/crontab

Just made those edits to the crontab file and will reboot these evening. Thanks, Mr. P!

SteveITS

@jimp said in 23.1 using more RAM:

try creating /etc/periodic.conf with the following content

@jrey said in 1100 upgrade, 22.05->23.01, high mem usage:

Yup I went a little further in testing, and pin pointed the exact step.
But I also then just disabled the 450.status-security in the config.
as it was configured out of box as (mail root) no one would ever see the output anyway.
following through I also sent the output to log files so in case I might like to look at it one day (NOT)
this thread details all the steps I took and at what point it breaks, the settings quoted on the reference thread will do the same as disabling 450.status-security
there is nothing to see there anyway, especially as configured out of box.
security_status_baseaudit_enable="NO"
security_status_pkg_checksum_enable="NO"
security_status_pkgaudit_enable="NO"

Agree it's not a "problem" unless one needs the memory. However, 1100 users are probably more sensitive to memory usage...that's one reason we sold 2100s instead. :) It looks alarming on the graph but at least with 4 GB, for most people it's a bit irrelevant if 30% or 50% is in use.

However if as jrey says it's an unused feature then it shouldn't hurt to disable it.

DefenderLLC

@steveits said in 23.1 using more RAM:

@jimp said in 23.1 using more RAM:

try creating /etc/periodic.conf with the following content

@jrey said in 1100 upgrade, 22.05->23.01, high mem usage:

Yup I went a little further in testing, and pin pointed the exact step.
But I also then just disabled the 450.status-security in the config.
as it was configured out of box as (mail root) no one would ever see the output anyway.
following through I also sent the output to log files so in case I might like to look at it one day (NOT)
this thread details all the steps I took and at what point it breaks, the settings quoted on the reference thread will do the same as disabling 450.status-security
there is nothing to see there anyway, especially as configured out of box.
security_status_baseaudit_enable="NO"
security_status_pkg_checksum_enable="NO"
security_status_pkgaudit_enable="NO"

Agree it's not a "problem" unless one needs the memory. However, 1100 users are probably more sensitive to memory usage...that's one reason we sold 2100s instead. :) It looks alarming on the graph but at least with 4 GB, for most people it's a bit irrelevant if 30% or 50% is in use.

However if as jrey says it's an unused feature then it shouldn't hurt to disable it.

Just rebooted after making those changes. I will report back here tomorrow morning!

Dobby_

After some time and all packets up to date (yesterday)
all went fine again, there is not so high usage of RAM (90%)
and Swap will be also not reaching out of space on top of
all the CPU is going back to normal too.

All in all, now the specs will be normal again like before
the update to 23.01.

Never again I will go with hard soldered RAM, the next
box will be sorted with upgrade able memory banks.

jimp

Honestly the cron thing is mostly a perception thing as well -- it just keeps a high disk activity job from crunching all the data on the disk and thus driving up ARC. Any high disk activity job could do it over time.

The real "solution" here is for you do tune the value of things like vfs.zfs.arc_max to levels you are comfortable with on your setup so it doesn't grow larger than you think it should. Note the weasel words there as that's primarily not a technical limit it will just give you a warm fuzzy feeling about not letting your RAM be used for caching to speed things up :-)

I opened https://redmine.pfsense.org/issues/14016 to address the cron changes.

You can install the System Patches package and then create an entry for ff715efce5e6c65b3d49dc2da7e1bdc437ecbf12 to apply the fix. After applying the patch you can either reboot or if you have the cron package installed, edit and save a job (without making changes) to trigger a rewrite of the cron config.

EDIT: For good measure I went back to a 22.05 ZFS install and ran periodic daily and ZFS ARC+wired usage shot up like mad, so even though the underlying behavior is the same, disabling the cron job should at least get back to not having it run ARC up every night.

DefenderLLC

@jimp said in 23.1 using more RAM:

Honestly the cron thing is mostly a perception thing as well -- it just keeps a high disk activity job from crunching all the data on the disk and thus driving up ARC. Any high disk activity job could do it over time.

The real "solution" here is for you do tune the value of things like vfs.zfs.arc_max to levels you are comfortable with on your setup so it doesn't grow larger than you think it should. Note the weasel words there as that's primarily not a technical limit it will just give you a warm fuzzy feeling about not letting your RAM be used for caching to speed things up :-)

I opened https://redmine.pfsense.org/issues/14016 to address the cron changes.

You can install the System Patches package and then create an entry for ff715efce5e6c65b3d49dc2da7e1bdc437ecbf12 to apply the fix. After applying the patch you can either reboot or if you have the cron package installed, edit and save a job (without making changes) to trigger a rewrite of the cron config.

EDIT: For good measure I went back to a 22.05 ZFS install and ran periodic daily and ZFS ARC+wired usage shot up like mad, so even though the underlying behavior is the same, disabling the cron job should at least get back to not having it run ARC up every night.

Glad you were able to replicate it. I edited the crontab file and commented out those 3 lines and rebooted. Will report back tomorrow morning! Thank you, Mr. P.!

Patch

@jimp said in 23.1 using more RAM:.

… there as that's primarily not a technical limit it will just give you a warm fuzzy feeling about not letting your RAM be used for caching to speed things up :- …

While for a static system this is technically correct. However in a real time software system there is a difference between

currently free memory and
could be made available if required.

The difference is essentially time, how long does the requesting process have to be stalled waiting for the required memory to be allocated to it. Where will this memory be allocated from, swap or zfs buffer garbage collection. Does this delay reduced throughput, or result in intermittent data loss / or crashes.

Where the memory is being used for user measurable device performance enhancement then the trade off can be justified. When it only helps after hours housekeeping, the cost is harder to justify. When it is used for redundant task run once a day, I’m at a loss to know any way of justify it.

Ideally ARC would release cache which is very rarely used but I’m not aware of that option being supported. The closest I have found is to manually set the ARC upper buffer limit to cover active buffer use, forcing ARC to prune rarely used buffer data. By default ARC uses 50% of all available ram to accelerate disk access. For a real time system such as pfsense which is not disk access limited, this is unlikely to be optimal. In the past pfsense severely restricted ARC buffer size however this appears to have been removed from the latest version. Looks like a regression to me.

bingo600

@jimp said in 23.1 using more RAM:

it just keeps a high disk activity job from crunching all the data on the disk and thus driving up ARC. Any high disk activity job could do it over time.

Hmmm ....

I have used ZFS since 2.4.5-p1.

I noticed a jump in ram consumption, when i switched to pfSense+ (22.??) first plus.
I have 8GB installed, and am quite sure i was using around 18% when on 2.6.0.

When i switched to Plus, it started out somewhat the same 18% , but during the next days it would gradually increase to around 40..43% usage, but it stayed there ... So it didn't look like a leak.
And i was not too worried, as it seemed stable at around low 40%., and i still had 4GB free.

I have NtopNG active on 20+ interfaces, and it seems like it starts a process per interface that gobbles up some mem,
But if NtopNG also logs the collected data to disk, then combined with the "ZFS & Disk Activity statement above" , that could be the reason for the increased usage.

This is my 23.01 Test Box (i3 / 8GB Ram) running my "home config" , uptime around 2 days
Dashboard shows 39% Mem usage.

Home 23.01 - i3/8G Ram - Uptime 2 days

.
.
.

This is my 22.05 Summerhouse Box (i5 / 8GB Ram) running my "summerhouse config" , uptime 173 days
Dashboard shows 46% Mem usage.

Summerhouse - 22.05 - i5/8G Ram - Uptime 173 days

Both w. NtopNG and 20+ Vlans , and running basically the same config.
Both are (sys)logging to a "remote linux" ...

/Bingo

jimp

As I mentioned above, if the wired usage is from ZFS ARC, you have the option to tune its usage at any time by setting a tunable for vfs.zfs.arc_max to a specific number of bytes (e.g. 268435456 for 256M). On FreeBSD 14 that isn't a loader tunable like it was on older versions, you can change the value live and it is immediately respected.

DefenderLLC

@jimp said in 23.1 using more RAM:

As I mentioned above, if the wired usage is from ZFS ARC, you have the option to tune its usage at any time by setting a tunable for vfs.zfs.arc_max to a specific number of bytes (e.g. 268435456 for 256M). On FreeBSD 14 that isn't a loader tunable like it was on older versions, you can change the value live and it is immediately respected.

Mystery solved. Disabling the periodic cron jobs fixed the issue. Thank you for your help, Mr. P!

jimp

Good to know that disabling the unnecessary cron bits helped, but be aware that any process that heavily hits the disk will trigger similar high ARC usage in the future as it tries to cache data.

If you are worried about the wired usage, I still recommend setting a value for vfs.zfs.arc_max to whatever amount of your RAM you feel comfortable with it using. Higher values will result in overall better disk performance, but disk performance isn't usually important for most firewall roles.

keyser

There is definitely an issue with how memory is consumed/released in 23.01

I have been using the tftp package for years to store a image of my Raspberry PI on my pfSense (on a remote site). Ever since 23.01, wired memory grows with about the size of files i transfer to pfSense, and is apparantly not released again (even though I stop and restart the TFTP service).

So it just takes a tftp transfer of 6 Gb to bring my 6100 to 100% memory consumption (2Gb is the normal level). Stopping services does not release it, only a restart does.

I havent tried (and would rather not) deleting my 22.05 boot environment to see if it is a ZFS issue when an older clone exists (from upgrade) of the running "default" environment.

edit: And I cannot see a process or get top to show where the wired memory is used. Everything in top only adds up to about about 1.6Gb of the 2Gb used by standard on my system

keyser

@jimp I tried creating a system tunable called vfs.zfs.arc_max and setting it 256Mb. It has no effect on the 100% wired memory usage (at least not without a reboot).

Also deleting the TFTP transferred file has no effect either (if it was somehow locked and kept in cache because of that).

jimp

@keyser Please start your own thread as that is probably a different issue.