Help with 25G Speeds on HA pfSense Routers (LACP) Using Mellanox ConnectX-5 NIC
-
Yeah you likely won't see 25Gbps. Especially not in a single thread TCP test like that.
Where exactly are you testing between in that iperf test?
-
@stephenw10 In the test where I wasn't getting the expected speeds pfsense was the iperf3 server and proxmox was the client. However if I make proxmox the server and pfsense the client I get the full 25G. Below are the results.
** PfSense as iper3 server**
root@idm-node01:~# iperf3 -c 10.10.92.2 -i 1
Connecting to host 10.10.92.2, port 5201
[ 5] local 10.10.92.10 port 53808 connected to 10.10.92.2 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 107 MBytes 896 Mbits/sec 275 1.20 MBytes
[ 5] 1.00-2.00 sec 448 MBytes 3.75 Gbits/sec 0 1.41 MBytes
[ 5] 2.00-3.00 sec 475 MBytes 3.98 Gbits/sec 29 1.25 MBytes
[ 5] 3.00-4.00 sec 481 MBytes 4.04 Gbits/sec 3 1.07 MBytes
[ 5] 4.00-5.00 sec 478 MBytes 4.01 Gbits/sec 0 1.36 MBytes
[ 5] 5.00-6.00 sec 481 MBytes 4.04 Gbits/sec 35 1.20 MBytes
[ 5] 6.00-7.00 sec 476 MBytes 4.00 Gbits/sec 0 1.46 MBytes
[ 5] 7.00-8.00 sec 476 MBytes 4.00 Gbits/sec 18 1.31 MBytes
[ 5] 8.00-9.00 sec 475 MBytes 3.98 Gbits/sec 20 1.15 MBytes
[ 5] 9.00-10.00 sec 479 MBytes 4.02 Gbits/sec 0 1.43 MBytes
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 4.27 GBytes 3.67 Gbits/sec 380 sender
[ 5] 0.00-10.00 sec 4.27 GBytes 3.67 Gbits/sec receiveriperf Done.
** Proxmox as server, pfsense as client**
Accepted connection from 10.10.92.2, port 18728
[ 5] local 10.10.92.10 port 5201 connected to 10.10.92.2 port 50384
[ ID] Interval Transfer Bitrate
[ 5] 0.00-1.00 sec 2.36 GBytes 20.3 Gbits/sec
[ 5] 1.00-2.00 sec 2.73 GBytes 23.4 Gbits/sec
[ 5] 2.00-3.00 sec 2.73 GBytes 23.4 Gbits/sec
[ 5] 3.00-4.00 sec 2.49 GBytes 21.4 Gbits/sec
[ 5] 4.00-5.00 sec 2.73 GBytes 23.4 Gbits/sec
[ 5] 5.00-6.00 sec 2.73 GBytes 23.5 Gbits/sec
[ 5] 6.00-7.00 sec 2.73 GBytes 23.5 Gbits/sec
[ 5] 7.00-8.00 sec 2.73 GBytes 23.5 Gbits/sec
[ 5] 8.00-9.00 sec 2.73 GBytes 23.5 Gbits/sec
[ 5] 9.00-10.00 sec 2.72 GBytes 23.4 Gbits/sec
[ 5] 10.00-10.00 sec 193 KBytes 12.4 Gbits/sec
[ ID] Interval Transfer Bitrate
[ 5] 0.00-10.00 sec 26.7 GBytes 22.9 Gbits/sec receiver**** This is the output from pfsense as the client as well***
Connecting to host 10.10.92.10, port 5201
Cookie: zbn2lcktyyydi2a56bdfequy7f7nb5un5ysv
TCP MSS: 1460 (default)
[ 5] local 10.10.92.2 port 50384 connected to 10.10.92.10 port 5201
Starting Test: protocol: TCP, 1 streams, 131072 byte blocks, omitting 0 seconds, 10 second test, tos 0
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 2.36 GBytes 2417 MBytes/sec 5 690 KBytes
[ 5] 1.00-2.00 sec 2.73 GBytes 2791 MBytes/sec 0 1.41 MBytes
[ 5] 2.00-3.00 sec 2.73 GBytes 2792 MBytes/sec 0 2.15 MBytes
[ 5] 3.00-4.00 sec 2.49 GBytes 2554 MBytes/sec 22 569 KBytes
[ 5] 4.00-5.00 sec 2.73 GBytes 2793 MBytes/sec 0 1.29 MBytes
[ 5] 5.00-6.00 sec 2.73 GBytes 2797 MBytes/sec 0 2.03 MBytes
[ 5] 6.00-7.00 sec 2.73 GBytes 2797 MBytes/sec 0 2.77 MBytes
[ 5] 7.00-8.00 sec 2.73 GBytes 2797 MBytes/sec 0 2.98 MBytes
[ 5] 8.00-9.00 sec 2.73 GBytes 2797 MBytes/sec 0 2.98 MBytes
[ 5] 9.00-10.00 sec 2.72 GBytes 2789 MBytes/sec 0 2.98 MBytes
Test Complete. Summary Results:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 26.7 GBytes 2732 MBytes/sec 27 sender
[ 5] 0.00-10.00 sec 26.7 GBytes 2732 MBytes/sec receiver
CPU Utilization: local/sender 73.3% (5.5%u/67.9%s), remote/receiver 72.3% (1.9%u/70.4%s)
snd_tcp_congestion cubic
rcv_tcp_congestion cubiciperf Done
-
pfSense is a bad server. It's optimised as a router. You should test through it if you possibly can rather than to or from it directly.
Seeing 25Gbps in a single stream when pfSense is sending is surprising. Impressive. Do you see more if you run multiple streams? Or multiple simultaneous iperf instances?
-
What config do you have on pfSense for that test? A lot of rules? Basic install?
-
@stephenw10 Pretty much just a basic install with HA and some vlans created. We are in the testing phase so we wanted to have as much of a baseline as possible. On your previous post you asked some good questions that I will try to test later today. Right now I have to do "work" ie email and other admin nonsense.
-
Update: I was able to do some more testing and I rechecked the MTU settings for everything and found some things I missed. I then set up to ubuntu vms on each proxmox node. Each proxmox node had the necessary vlans created (I'm using openvswitch) and I was able to get 25gb across the vlans from one ubuntu box to another.
-
Interesting, I may want to do some additional testing in my lab on this, I've never managed to push PF much beyond about 10 gig, even with iperf and ideal scenarios, so this is super interesting.
-
@planedrop I spent all day at it and just started looking at everything again because it didn't add up. Heres a screen shot of one of the results. 
I also tried with parallel streams and it worked as expected the retrys went way down. -
@kilo40 Interesting, I'll see if I can duplicate this in my lab, that's crazy fast but awesome to see nonetheless.
-
That is crazy fast! Are you seeing that both ways?
-
@stephenw10 Yep, tested both ways and everything seems to be working great.
-
Nice. Surprising from that CPU. The NICs must really be helping.
-
Simply stunning performance. I think you will be helping the rest of us from now on!
Is this VT-d stretching its legs with the ConnectX?
️ -
S stephenw10 referenced this topic on
-
S stephenw10 referenced this topic on
