Netgate 3100 won't boot >> Unable to read file ubldr.bin

parzival

It seems we had a power outage and the system was up but it said there was a crash reported. Most pages didn't work and there was no crash report. Several services were also down.
Upon Rebooting the system, it didn't come back up.

Logged on to the console. Here is what the console shows. Is there a way to repair the partition and salvage the installation? If not, what's the best way to reinstall?

General initialization - Version: 1.0.0
AVS selection from EFUSE disabled (Skip reading EFUSE values)
Overriding default AVS value to: 0x23
Detected Device ID 6820
High speed PHY - Version: 2.0

Init Customer board board SerDes lanes topology details:
 | Lane # | Speed|    Type     |
 ------------------------------|
 |   0    |  3   |  SATA0      |
 |   1    |  5   |  PCIe0      |
 |   2    |  3   |  SATA1      |
 |   3    |  4   |  SGMII2     |
 |   4    |  5   |  PCIe1      |
 |   5    |  5   |  USB3 HOST1 |
 -------------------------------
PCIe Ref. Clock Buffer Control is 0xf00015bf, setting to 0xf00015bf
SOC_CONTROL_REG1 is 0xf00015bf, setting to 0x0707c0f3
PCIe, Idx 0: detected no link
PCIe, Idx 1: detected no link
High speed PHY - Ended Successfully
mv_ddr: mv_ddr-armada-17.06.1-g07f8294 (Oct  8 2018 - 12:59:22)
DDR4 Training Sequence - Switching XBAR Window to FastPath Window
mv_ddr: completed successfully

 __   __                      _ _
|  \/  | __ _ _ ____   _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| |  | | (_| | |   \ V /  __/ | |
|_|  |_|\__,_|_|    \_/ \___|_|_|
         _   _     ____              _
        | | | |   | __ )  ___   ___ | |_
        | | | |___|  _ \ / _ \ / _ \| __|
        | |_| |___| |_) | (_) | (_) | |_
         \___/    |____/ \___/ \___/ \__|
 ** LOADER **


U-Boot 2013.01-02879-geb5cbf6642 (Oct 08 2018 - 12:59:19) Marvell version: devel-17.06.0

Board: Rogue-1
SoC:   MV88F6820 Rev A0
       running 2 CPUs
CPU:   ARM Cortex A9 MPCore (Rev 1) LE
       CPU 0
       CPU    @ 1600 [MHz]
       L2     @ 800 [MHz]
       TClock @ 250 [MHz]
       DDR4    @ 800 [MHz]
       DDR4 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM:  2 GiB
MMC:   mv_sdh: 0
DBG: Calling spi_flash_probe from env_relocate_spec()
SF: Probing bus 0 cs 0 @ 20000000Hz mode 3
SF: Detected W25Q32JV with page size 4 KiB, total 4 MiB
PCI-e 0: Detected No Link.
PCI-e 1: Detected No Link.
USB2.0 0: Host Mode
USB3.0 1: Host Mode

Map:   Code:                    0x7fedc000:0x7ff9741c
       BSS:                     0x7ffef600
       Stack:                   0x7f4cbf20
       Heap:                    0x7f4cc000:0x7fedc000
       U-Boot Environment:      0x00100000:0x00110000 (SPI)

Board configuration detected:
Net:
|  port  | Interface | PHY address  |
|--------|-----------|--------------|
| egiga0 |   RGMII   |     0x00     |
| egiga1 |   RGMII   |     0x01     |
| egiga2 |   SGMII   |   In-Band    |
egiga0 [PRIME], egiga1, egiga2
Hit any key to stop autoboot:  0
reading ubldr.bin
** Unable to read file ubldr.bin **
## Starting application at 0x00200000 ...

parzival

FYI, opened up a ticket. Received instructions on how to reinstall firmware. Support is very fast and efficient.