Placa de rede para de funcionar

fcostars

@stephenw10
ok, I did as you instructed me!
this was the result

re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0xe000-0xe0ff mem 0xf7b00000-0xf7b00fff,0xf0300000-0xf0303fff irq 17 at device 0.0 on pci4
re0: Using 1 MSI-X message
re0: Chip rev. 0x2c800000
re0: MAC rev. 0x00100000
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0
rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
re0: Using defaults for TSO: 65518/35/2048
re0: Ethernet address: 00:e0:4c:68:20:25
re0: netmap queues/slots: TX 1/256, RX 1/256

Thank you very much!

Now I'll wait if there will be any problems.

fcostars

This post is deleted!

Potapuch

This post is deleted!

fcostars

@stephenw10

Now it worked!

I added the lines in the conf.local file.
if_re_load="YES" >> /boot/loader.conf.local
if_re_name="/boot/modules/if_re.ko" >> /boot/loader.conf.local

re0: <Realtek PCIe GbE Family Controller> port 0xe000-0xe0ff mem 0xf7b00000-0xf7b00fff,0xf0300000-0xf0303fff irq 17 at device 0.0 on pci4
re0: Using Memory Mapping!
re0: Using 1 MSI-X message
re0: version:1.98.00
re0: Ethernet address: 00:e0:4c:68:20:25

stephenw10

Nice. Yes you need to see the 'version:' logged to know it has loaded.

See if that stops the timeouts.

Steve

fcostars

@stephenw10
Thank you very much!

fcostars

@stephenw10
One last question.
Which network card do you recommend buying?

stephenw10

Something Intel based. Hence I didn't expect that HP card you referred to to be an issue. Any i350 NIC will be good. There are a lot of fake Intel NICs around though so be careful.

fcostars

@stephenw10 Thank you!

sTicKs23

I had the same problem with a Realtek onboard LAN for many years.

What actually worked for me, was to clone https://github.com/alexdupre/rtl_bsd_drv to a FreeBSD 14 instance (branch v1.98) and, compile the driver with make, backup the old if_re.ko from /boot/kernel, and copy the compiled driver over to /boot/kernel.

Already compiled driver if anyone is looking for it (zip pass 123): https://1drv.ms/u/s!AteTpjotrz-qiuMVNwFrD6CY72xSpg?e=Ftc6ui

stephenw10

That's the same driver that is built in the kmod: https://github.com/pfsense/FreeBSD-ports/blob/devel/net/realtek-re-kmod/Makefile#L11
In general it's better to use the one from our repo since it's built against our kernel.

But compiling your own driver is good practice.

Steve

sTicKs23

Hell @stephenw10,
Thank you for your response.

In my case, I'm running a custom kernel, because pfSense 2.7.0 is not shipping all the kernel modules like 2.6.0 did (please check https://forum.netgate.com/topic/183148/missing-kernel-modules-on-release-2-7-0).

At some point I tried using 'realtek-re-kmod-198.00_3.pkg' but I was getting some kernel panics and driver compilation was the only way I got over this.

Thanks!

stephenw10

Hmm, not sure where you got that from then but it wasn't our repo:

[2.7.0-RELEASE][admin@pfsense.fire.box]/root: pkg search realtek
realtek-re-kmod-198.00_1       Kernel driver for Realtek PCIe Ethernet Controllers