uPnP & NAT-PMP errors in Routing Log

sysadminfromhell · Nov 14, 2023, 8:16 AM

Hello everyone,

since I had to replace my old x550-T2 with an x710-T4L due a defect on the X550 Card the "routing" log in pfSense runnig full with the following:

Nov 14 09:13:32	miniupnpd	36793	try_sendto(sock=9, len=404, dest=239.255.255.250:1900): sendto: Capabilities insufficient
Nov 14 09:13:32	miniupnpd	36793	try_sendto(sock=9, len=476, dest=239.255.255.250:1900): sendto: Capabilities insufficient
Nov 14 09:13:32	miniupnpd	36793	try_sendto(sock=9, len=412, dest=239.255.255.250:1900): sendto: Capabilities insufficient
Nov 14 09:13:32	miniupnpd	36793	try_sendto(sock=9, len=472, dest=239.255.255.250:1900): sendto: Capabilities insufficient
Nov 14 09:13:32	miniupnpd	36793	try_sendto(sock=9, len=412, dest=239.255.255.250:1900): sendto: Capabilities insufficient
Nov 14 09:13:32	miniupnpd	36793	try_sendto(sock=9, len=452, dest=239.255.255.250:1900): sendto: Capabilities insufficient
Nov 14 09:13:32	miniupnpd	36793	try_sendto(sock=9, len=412, dest=239.255.255.250:1900): sendto: Capabilities insufficient
Nov 14 09:13:32	miniupnpd	36793	try_sendto(sock=9, len=466, dest=239.255.255.250:1900): sendto: Capabilities insufficient
Nov 14 09:13:32	miniupnpd	36793	try_sendto(sock=9, len=484, dest=239.255.255.250:1900): sendto: Capabilities insufficient
Nov 14 09:13:32	miniupnpd	36793	try_sendto(sock=9, len=468, dest=239.255.255.250:1900): sendto: Capabilities insufficient
Nov 14 09:13:32	miniupnpd	36793	try_sendto(sock=9, len=468, dest=239.255.255.250:1900): sendto: Capabilities insufficient

Restarting the Service or reconfiguring it doesnt change this error at all.
How can I troubleshoot this error?

Kind regards,

stephenw10 · Nov 15, 2023, 8:31 AM

The only time I've seen that is when the interface isn't properly configured.

You swapped an ix for an ixl NIC. I guess it's something still referencing the old interface though I would expected resaving the upnp config to correct that.
Check: /var/etc/miniupnpd.conf

sysadminfromhell · Nov 15, 2023, 8:31 AM

@stephenw10 Hi Stephen, thanks for you answer but the /var/etc/miniuonod.conf ile looks good. As you know I replaced the x710 once again with a different x550 (working) one due the vlan problematik on the x710. But still the same issue accurs. Here my file:

cat /var/etc/miniupnpd.conf
ext_ifname=pppoe0
port=2189
listening_ip=ix0
listening_ip=ix1
listening_ip=ix3
listening_ip=ix1.100
listening_ip=ix1.30
listening_ip=tun_wg0
packet_log=yes
system_uptime=yes
secure_mode=yes
presentation_url=https://192.168.178.1/
uuid=d41d8cd9-f00b-204e-9800-998ecf8427e
serial=D41D8CD9
model_number=23.09-RELEASE
allow 1024-65535 192.168.0.0/16 1024-65535
allow 1024-65535 172.16.0.0/16 1024-65535
queue=qOthersLow
enable_upnp=yes
enable_natpmp=yes

sysadminfromhell · Nov 15, 2023, 8:38 AM

@stephenw10 okay I just deselect all interfaces and disabled the service once and then reconfigure it. Now it seems to work, I will keep in eye on it today and will report later.

stephenw10 · Nov 15, 2023, 2:42 PM

Hmm, that's weird. Does the conf file still look the same?

sysadminfromhell · Nov 23, 2023, 9:08 AM

@stephenw10 so I was able to fix it with editing the file via the cli. Now its working like it should.

stephenw10 · Nov 23, 2023, 1:13 PM

Hmm, what did you actually change? I'd expect to see that repopulated correctly after saving the config in the gui.