Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    QL41164 4 port 10GB NIC on 2.7

    Scheduled Pinned Locked Moved Hardware
    14 Posts 2 Posters 920 Views
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • A
      ADC1111 @stephenw10
      last edited by

      @stephenw10 Ran kldload if_qlnxe at the shell. It scrolls through a bunch of commands and ultimately ends at a blank cursor and is locked up.

      last line says "db:0:kdb.enter.default> reset

      Blank cursor after this and server is hard locked and has to be powered off and back on.

      1 Reply Last reply Reply Quote 0
      • stephenw10S
        stephenw10 Netgate Administrator
        last edited by

        Ah, not good. Did you get a crash report after you rebooted?

        A 1 Reply Last reply Reply Quote 0
        • A
          ADC1111 @stephenw10
          last edited by

          @stephenw10 Yes. Here's the info:

          ql0: <Qlogic 10GbE/25GbE/40GbE PCI CNA (AH) Adapter-Ethernet Function v2.0.112> mem 0xdb740000-0xdb75ffff,0xd9000000-0xd97fffff,0xdb7c0000-0xdb7cffff irq 48 at device 0.0 numa-domain 0 on pci2
          ql0: qlnx_set_personality: ETH_IWARP
          ql0: setting parameters required by iWARP dev

          Fatal trap 12: page fault while in kernel mode
          cpuid = 3; apic id = 03
          fault virtual address = 0x0
          fault code = supervisor read instruction, page not present
          instruction pointer = 0x20:0x0
          stack pointer = 0x28:0xfffffe018aa67628
          frame pointer = 0x28:0xfffffe018aa67650
          code segment = base 0x0, limit 0xfffff, type 0x1b
          = DPL 0, pres 1, long 1, def32 0, gran 1
          processor eflags = interrupt enabled, resume, IOPL = 0
          current process = 77429 (kldload)
          rdi: fffff8000205d000 rsi: fffffe018aa676a0 rdx: 00000000c0306938
          rcx: 00000000c0306938 r8: 0000000000000000 r9: 0000000000000010
          rax: 0000000000000000 rbx: fffffe018aa676a0 rbp: fffffe018aa67650
          r10: 0000000000000000 r11: fffffe002bc0f000 r12: 0000000000008802
          r13: fffff80201814010 r14: fffffe0020280f90 r15: 0000000000000016
          trap number = 12
          panic: page fault

          1 Reply Last reply Reply Quote 0
          • stephenw10S
            stephenw10 Netgate Administrator
            last edited by

            Can you upload the full crash report here? https://nc.netgate.com/nextcloud/index.php/s/scjMBg5q8q8gdDx

            A 1 Reply Last reply Reply Quote 0
            • A
              ADC1111 @stephenw10
              last edited by

              @stephenw10 Good morning. I got tied up last night but I've uploaded the log now.

              1 Reply Last reply Reply Quote 0
              • stephenw10S
                stephenw10 Netgate Administrator
                last edited by

                Ok so 5 indentical backtraces:

                db:0:kdb.enter.default>  bt
Tracing pid 11136 tid 100515 td 0xfffffe001e8c7e40
kdb_enter() at kdb_enter+0x32/frame 0xffffffff83680300
vpanic() at vpanic+0x163/frame 0xffffffff83680430
panic() at panic+0x43/frame 0xffffffff83680490
trap_fatal() at trap_fatal+0x40c/frame 0xffffffff836804f0
trap_pfault() at trap_pfault+0x4f/frame 0xffffffff83680550
calltrap() at calltrap+0x8/frame 0xffffffff83680550
--- trap 0xc, rip = 0, rsp = 0xffffffff83680628, rbp = 0xffffffff83680650 ---
??() at 0/frame 0xffffffff83680650
dump_iface() at dump_iface+0x145/frame 0xffffffff83680700
rtnl_handle_ifevent() at rtnl_handle_ifevent+0xa9/frame 0xffffffff83680780
if_attach_internal() at if_attach_internal+0x3cf/frame 0xffffffff836807d0
ether_ifattach() at ether_ifattach+0x2c/frame 0xffffffff83680810
qlnx_init_ifnet() at qlnx_init_ifnet+0x2c6/frame 0xffffffff83680860
qlnx_pci_attach() at qlnx_pci_attach+0x7d9/frame 0xffffffff83680900
device_attach() at device_attach+0x3be/frame 0xffffffff83680950
device_probe_and_attach() at device_probe_and_attach+0x41/frame 0xffffffff83680980
pci_driver_added() at pci_driver_added+0xf2/frame 0xffffffff836809c0
devclass_driver_added() at devclass_driver_added+0x39/frame 0xffffffff83680a00
devclass_add_driver() at devclass_add_driver+0x11e/frame 0xffffffff83680a40
module_register_init() at module_register_init+0x85/frame 0xffffffff83680a70
linker_load_module() at linker_load_module+0xbd5/frame 0xffffffff83680d70
kern_kldload() at kern_kldload+0x16a/frame 0xffffffff83680dd0
sys_kldload() at sys_kldload+0x5c/frame 0xffffffff83680e00
amd64_syscall() at amd64_syscall+0x109/frame 0xffffffff83680f30
fast_syscall_common() at fast_syscall_common+0xf8/frame 0xffffffff83680f30
--- syscall (304, FreeBSD ELF64, kldload), rip = 0x111724e8e8aa, rsp = 0x1117239be268, rbp = 0x1117239be7e0 ---

                That definitely a problem withthe driver/NIC then.

                There is a known bug with that driver but what you're hitting is not that: https://redmine.pfsense.org/issues/13028

                Are you able to test this in FreeBSD 14?

                A 1 Reply Last reply Reply Quote 0
                • A
                  ADC1111 @stephenw10
                  last edited by ADC1111

                  @stephenw10 I can drop a quick image and give it a whirl.Another thought I had was putting 2019 on the box. Which works fine then doing the firewall as a VM. Thoughts on that method? Currently I was hoping to do bare metal but if that's causing some issues I can pop 2019 on it which I know works as I did that as a test already to make sure the hardware was functional.

                  1 Reply Last reply Reply Quote 0
                  • stephenw10S
                    stephenw10 Netgate Administrator
                    last edited by

                    2019? Some hypervisor?

                    A 1 Reply Last reply Reply Quote 0
                    • A
                      ADC1111 @stephenw10
                      last edited by

                      @stephenw10 Sorry. Yes. HYper-V I have a license for it that I could ultimately use.

                      1 Reply Last reply Reply Quote 0
                      • stephenw10S
                        stephenw10 Netgate Administrator
                        last edited by

                        Yup, you could certainly do that. Though I would personally choose any other hypervisor.

                        But I would test FreeBSD 14 on it bare metal if you can. If it throws the same panic there we can open an upstream bug for it.

                        Steve

                        1 Reply Last reply Reply Quote 0
                        • First post
                          Last post
                        Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.