Upgrade 1100 to 21.02 lost DHCP
-
Hi,
My SG-1100 was working on 2.4, I thought I upgrade to the latest. After upgrade, there was no DHCP and I could not login. I tried to pin reset, still no joy. I can login to console, but nothing seems to be running. The console boot log as follows. Can I still recover?
TIM-1.0 WTMI-armada-17.10.5-34ce216 WTMI: system early-init SVC REV: 5, CPU VDD voltage: 1.225V Fill memory before self refresh...done Now in Self-refresh Mode Exited self-refresh ... Self refresh Pass. DDR self test mode test done!! Vref read training =================== Final vdac_value 0x0000001F Vref write training =================== Final vref_value 0x00000021 DLL TUNING ============== DLL 0xc0001050[21:16]: [1,31,19] DLL 0xc0001050[29:24]: [5,2c,18] DLL 0xc0001054[21:16]: [5,34,1c] DLL 0xc0001054[29:24]: [6,32,1c] DLL 0xc0001074[21:16]: [0,3f,1f] DLL 0xc0001074NOTICE: Booting Trusted Firmware NOTICE: BL1: v1.3(release):armada-17.10.8:34247e0 NOTICE: BL1: Built : 16:19:41, Nov 1 2NOTICE: BL2: v1.3(release):armada-17.10.8:34247e0 NOTICE: BL2: Built : 16:19:45, Nov 1 20NOTICE: BL31: v1.3(release):armada-17.10.8:34247e0 NOTICE: BL31: U-Boot 2017.03-armada-17.10.2-g6a6581a-dirty (Nov 01 2018 - 16:04:57 -0300) Model: Marvell Armada 3720 Community Board ESPRESSOBin CPU @ 1200 [MHz] L2 @ 800 [MHz] TClock @ 200 [MHz] DDR @ 750 [MHz] DRAM: 1 GiB U-Boot DT blob at : 000000003f716298 Comphy-0: USB3 5 Gbps Comphy-1: PEX0 2.5 Gbps Comphy-2: SATA0 6 Gbps SATA link 0 timeout. AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode flags: ncq led only pmp fbss pio slum part sxs PCIE-0: Link down MMC: sdhci@d0000: 0, sdhci@d8000: 1 SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB, total 4 MiB Net: eth0: neta@30000 [PRIME] Hit any key to stop autoboot: 0 Card did not respond to voltage select! mmc_init: -95, time 41 ** Bad device mmc 0 ** Card did not respond to voltage select! mmc_init: -95, time 23 ** Bad device mmc 0 ** ## Starting EFI application at 05000000 ... Card did not respond to voltage select! mmc_init: -95, time 23 Scanning disk sdhci@d8000.blk... Found 4 disks <snip to save space> >> FreeBSD EFI boot block Loader path: /boot/loader.efi Initializing modules: ZFS UFS Probing 4 block devices......* done ZFS found no pools UFS found 1 partition command args: -S115200 Consoles: EFI console Reading loader env vars from /efi/freebsd/loader.env Setting currdev to disk0p3: FreeBSD/arm64 EFI loader, Revision 1.1 Command line arguments: loader.efi -S115200 Image base: 0x3c55e008 EFI version: 2.05 EFI Firmware: Das U-boot (rev 0.00) Console: efi (0x1000) Load Path: mmc_blk1:3 Load Device: mmc_blk1:3 Trying ESP: mmc_blk1:3 Setting currdev to disk0p3: Loading /boot/defaults/loader.conf Loading /boot/defaults/loader.conf Loading /boot/device.hints Loading /boot/loader.conf Loading /boot/loader.conf.local | / __ _ __ / _|___ ___ _ __ ___ ___ _ | '_ \| |_/ __|/ _ \ '_ \/ __|/ _ \ _| |_ | |_) | _\__ \ __/ | | \__ \ __/ |_ _| | .__/|_| |___/\___|_| |_|___/\___| |_| |_| ╔════ Welcome to Netgate pfSense Plus ════╗ __________________________ ║ ║ / ___\ ║ 1. Boot Multi user [Enter] ║ | /` ║ 2. Boot Single user ║ | / :-| ║ 3. Escape to loader prompt ║ | _________ ___/ /_ | ║ 4. Reboot ║ | /` ____ / /__ ___/ | ║ 5. Cons: Serial ║ | / / / / / / | ║ ║ | / /___/ / / / | ║ Options: ║ | / ______/ / / _ | ║ 6. Kernel: default/kernel (1 of 2) ║ |/ / / / _| |_ | ║ 7. Boot Options ║ / /___/ |_ _| | ║ ║ / |_| | ║ ║ /_________________________/ ╚═════════════════════════════════════════╝ | __ _ __ / _|___ ___ _ __ ___ ___ _ | '_ \| |_/ __|/ _ \ '_ \/ __|/ _ \ _| |_ | |_) | _\__ \ __/ | | \__ \ __/ |_ _| | .__/|_| |___/\___|_| |_|___/\___| |_| |_| ╔════ Welcome to Netgate pfSense Plus ════╗ __________________________ ║ ║ / ___\ ║ 1. Boot Multi user [Enter] ║ | /` ║ 2. Boot Single user ║ | / :-| ║ 3. Escape to loader prompt ║ | _________ ___/ /_ | ║ 4. Reboot ║ | /` ____ / /__ ___/ | ║ 5. Cons: Video ║ | / / / / / / | ║ ║ | / /___/ / / / | ║ Options: ║ | / ______/ / / _ | ║ 6. Kernel: default/kernel (1 of 2) ║ |/ / / / _| |_ | ║ 7. Boot Options ║ / /___/ |_ _| | ║ ║ / |_| | ║ ║ /_________________________/ ╚═════════════════════════════════════════╝ Loading kernel... /boot/kernel/kernel text=0xc1ae9c data=0x12e9380 data=0x0+0x2d587e syms=[0x8+0x17c4a8+0x8+0x143fc8] Loading configured modules... can't find '/etc/hostid' can't find '/boot/entropy' Using DTB provided by EFI at 0x8000000. ---<<BOOT>>--- Copyright (c) 1992-2021 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 12.3-STABLE plus-RELENG_22_01-n202637-97cc5c23e13 pfSense arm64 FreeBSD clang version 10.0.1 (git@github.com:llvm/llvm-project.git llvmorg-10.0.1-0-gef32c611aa2) VT: init without driver. real memory = 1073729536 (1023 MB) avail memory = 1006649344 (960 MB) Starting CPU 1 (1) FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs arc4random: no preloaded entropy cache random: entropy device external interface wlan: mac acl policy registered ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE. ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (ipw_bss_fw, 0xffff00000021cfc8, 0) error 1 ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE. ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffff00000021d074, 0) error 1 ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE. ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffff00000021d120, 0) error 1 iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE. iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (iwi_bss_fw, 0xffff00000021d1cc, 0) error 1 iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE. iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (iwi_ibss_fw, 0xffff00000021d278, 0) error 1 iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE. iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (iwi_monitor_fw, 0xffff00000021d324, 0) error 1 WARNING: Device "g_ctl" is Giant locked and may be deleted before FreeBSD 14.0. MAP 3e700000 mode 2 pages 1 MAP 3ffa6000 mode 2 pages 1 WARNING: Device "openfirm" is Giant locked and may be deleted before FreeBSD 14.0. WARNING: Device "pci" is Giant locked and may be deleted before FreeBSD 14.0. [ath_hal] loaded WARNING: Device "kbd" is Giant locked and may be deleted before FreeBSD 14.0. kbd0 at kbdmux0 ofwbus0: <Open Firmware Device Tree> simplebus0: <Flattened device tree simple bus> on ofwbus0 simplebus1: <Flattened device tree simple bus> on simplebus0 simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0x13800-0x138ff,0x13c00-0x13c1f on simplebus1 simple_mfd1: <Simple MFD (Multi-Functions Device)> mem 0x18800-0x188ff,0x18c00-0x18c1f on simplebus1 psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0 gic0: <ARM Generic Interrupt Controller v3.0> mem 0x1d00000-0x1d0ffff,0x1d40000-0x1d7ffff,0x1d80000-0x1d81fff,0x1d90000-0x1d91fff,0x1da0000-0x1dbffff irq 27 on simplebus1 gpio0: <Armada 37x0 North Bridge GPIO Controller> mem 0x13800-0x138ff,0x13c00-0x13c1f irq 28,29,30,31,32,33,34,35,36,37,38,39 on simple_mfd0 gpiobus0: <OFW GPIO bus> on gpio0 gpio1: <Armada 37x0 South Bridge GPIO Controller> mem 0x18800-0x188ff,0x18c00-0x18c1f irq 40,41,42,43,44 on simple_mfd1 gpiobus1: <OFW GPIO bus> on gpio1 gpioregulator0: <GPIO controlled regulator> on ofwbus0 generic_timer0: <ARMv8 Generic Timer> irq 0,1,2,3 on ofwbus0 Timecounter "ARM MPCore Timecounter" frequency 12500000 Hz quality 1000 Event timer "ARM MPCore Eventtimer" frequency 12500000 Hz quality 1000 cpulist0: <Open Firmware CPU Group> on ofwbus0 cpu0: <Open Firmware CPU> on cpulist0 cpu1: <Open Firmware CPU> on cpulist0 pmu0: <Performance Monitoring Unit> irq 4 on ofwbus0 spi0: <Armada 37x0 SPI controller> mem 0x10600-0x10fff irq 6 on simplebus1 iichb0: <Marvell Armada 37x0 IIC controller> mem 0x11000-0x11023 irq 7 on simplebus1 iicbus0: <OFW I2C bus> on iichb0 iic0: <I2C generic I/O> on iicbus0 uart0: <Marvell Armada 3700 UART> mem 0x12000-0x121ff irq 9,10,11 on simplebus1 uart0: console (115200,n,8,1) gpioc0: <GPIO controller> on gpio0 syscon_generic_dev0: <syscon> mem 0x14000-0x1405f on simplebus1 gpioc1: <GPIO controller> on gpio1 mvneta0: <NETA controller> mem 0x30000-0x33fff irq 14 on simplebus1 mvneta0: version is 10 mvneta0: Ethernet address: f0:ad:4e:17:6d:ad mdio0: <MDIO> on mvneta0 e6000sw0: <Marvell 88E6341> on mdio0 e6000sw0: multi-chip addressing mode (0x1) e6000sw0: CPU port at 0 e6000sw0: fixed port at 0 e6000sw0: PHY at port 1 miibus0: <MII bus> on e6000sw0 e1000phy0: <Marvell 88E1000 Gigabit PHY> PHY 17 on miibus0 e1000phy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto e6000sw0: PHY at port 2 miibus1: <MII bus> on e6000sw0 e1000phy1: <Marvell 88E1000 Gigabit PHY> PHY 18 on miibus1 e1000phy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto e6000sw0: PHY at port 3 miibus2: <MII bus> on e6000sw0 e1000phy2: <Marvell 88E1000 Gigabit PHY> PHY 19 on miibus2 e1000phy2: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto e6000sw0: switch is ready. etherswitch0: <Switch controller> on e6000sw0 xhci0: <Marvell Integrated USB 3.0 controller> mem 0x58000-0x5bfff irq 16 on simplebus1 xhci0: 32 bytes context size, 32-bit DMA usbus0 on xhci0 ehci0: <Marvell Integrated USB 2.0 controller> mem 0x5e000-0x5ffff irq 17 on simplebus1 usbus1: EHCI version 1.0 usbus1 on ehci0 sdhci_xenon0: <Armada Xenon SDHCI controller> mem 0xd0000-0xd02ff,0x1e808-0x1e80b irq 24 on simplebus1 mmc0: <MMC/SD bus> on sdhci_xenon0 sdhci_xenon1: <Armada Xenon SDHCI controller> mem 0xd8000-0xd82ff,0x17808-0x1780b irq 25 on simplebus1 mmc1: <MMC/SD bus> on sdhci_xenon1 ahci0: <AHCI SATA controller> mem 0xe0000-0xe1fff irq 26 on simplebus1 ahci0: AHCI v1.30 with 1 6Gbps ports, Port Multiplier supported with FBS ahcich0: <AHCI channel> at channel 0 on ahci0 pcib0: <Marvell Armada 3700 PCIe Bus Controller> mem 0xd0070000-0xd008ffff irq 5 on simplebus0 pcib0: link never came up pci0: <PCI bus> on pcib0 gpioled0: <GPIO LEDs> on ofwbus0 cryptosoft0: <software crypto> armv8crypto0: <AES-CBC> Timecounters tick every 1.000 msec mvneta0: link state changed to UP spibus0: <OFW SPI bus> on spi0 mx25l0: <M25Pxx Flash Family> at cs 0 mode 0 on spibus0 mx25l0: device type mx25u3235f, size 4096K in 64 sectors of 64K, erase size 4K e6000sw0port1: link state changed to DOWN e6000sw0port2: link state changed to DOWN e6000sw0port3: link state changed to DOWN usbus0: 5.0Gbps Super Speed USB v3.0 usbus1: 480Mbps High Speed USB v2.0 ugen0.1: <Marvell XHCI root HUB> at usbus0 uhub0: <Marvell XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0 ugen1.1: <Marvell EHCI root HUB> at usbus1 uhub1: <Marvell EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 mmc0: No compatible cards found on bus uhub0: 2 ports with 2 removable, self powered mmc1: Failed to set VCCQ for card at relative address 2 mmcsd0: 8GB <MMCHC DG4008 0.1 SN 21670217 MFG 08/2020 by 69 0x0000> at mmc1 50.0MHz/8bit/65535-block mmcsd0boot0: 4MB partition 1 at mmcsd0 mmcsd0boot1: 4MB partition 2 at mmcsd0 mmcsd0rpmb: 4MB partition 3 at mmcsd0 Release APs...arc4random: no preloaded entropy cache done Trying to mount root from ufs:/dev/ufsid/5f60d5420316127a [rw,noatime]... CPU 0: ARM Cortex-A53 r0p4 affinity: 0 Instruction Set Attributes 0 = <CRC32,SHA2,SHA1,AES+PMULL> Instruction Set Attributes 1 = <> Processor Features 0 = <GIC,AdvSIMD,Float,EL3 32,EL2 32,EL1 32,EL0 32> Processor Features 1 = <0> Memory Model Features 0 = <4k Granule,64k Granule,S/NS Mem,MixedEndian,16bit ASID,1TB PA> Memory Model Features 1 = <> Memory Model Features 2 = <32b CCIDX,48b VA> Debug Features 0 = <2 CTX Breakpoints,4 Watchpoints,6 Breakpoints,PMUv3,Debug v8> Debug Features 1 = <0> Auxiliary Features 0 = <0> Auxiliary Features 1 = <0> CPU 1: ARM Cortex-A53 r0p4 affinity: 1 WARNING: / was not properly dismounted WARNING: /: mount pending error: blocks 13136 files 99 Warning: no time-of-day clock registered, system time will not be set accurately FreeBSD/arm64 (Amnesiac) (ttyu0) login: uhub1: 1 port with 1 removable, self powered e6000sw0port2: link state changed to UP -
If it's that old it probably can't get current anyway:
https://docs.netgate.com/pfsense/en/latest/troubleshooting/upgrades-1100-2100.html
I would reinstall (it's a free ticket to get the file) and restore from backup.Though "Bad device mmc 0" doesn't sound good. eMMC has a lifetime but you probably can't install the utility to check that in this state:
https://docs.netgate.com/pfsense/en/latest/troubleshooting/disk-lifetime.html -
** Bad device mmc 0 **is a normal message from uboot on the 1100. It's because the uSD card slot is not populated. -
@SteveITS said in Upgrade 1100 to 21.02 lost DHCP:
If it's that old it probably can't get current anyway:
https://docs.netgate.com/pfsense/en/latest/troubleshooting/upgrades-1100-2100.html
I would reinstall (it's a free ticket to get the file) and restore from backup.Though "Bad device mmc 0" doesn't sound good. eMMC has a lifetime but you probably can't install the utility to check that in this state:
https://docs.netgate.com/pfsense/en/latest/troubleshooting/disk-lifetime.htmlYes, I logged a ticket and did a reinstall. Restored operations. Thank you for the disk lifetime link.
