2.7.2 Fresh install fails: "Failed to run the post installation script"
-
Use option 8 there to reach the command line first.
-
@stephenw10 said in 2.7.2 Fresh install fails: "Failed to run the post installation script":
Use option 8 there to reach the command line first.
Ah, THANK YOU, that worked.
It appeared I didn't have a bootloader.conf file, so I created a new one with the two lines.After that I rebooted. Problem then was I still didn't autoboot to pfsense, but I managed to change the boot order and now it loads pfsense immediately and I end up at the command line to the mountroot> prompt.
Is this correct?
-
Ah, looks like you created a file in the wrong location. The file definitely exists but the correct command is:
ee /boot/loader.conf...which it looks like I typo'd above.
-
@stephenw10 said in 2.7.2 Fresh install fails: "Failed to run the post installation script":
Ah, looks like you created a file in the wrong location. The file definitely exists but the correct command is:
ee /boot/loader.conf...which it looks like I typo'd above.
lol, ok.
I will redo. Should I delete the other? And if so, how? -
It doesn't matter the file will be ignored.
But you can remove it with
rm /bootloader.conf -
@stephenw10 said in 2.7.2 Fresh install fails: "Failed to run the post installation script":
https://forum.netgate.com/post/1173457
I am having similar problems to original poster on a Protectli VP2420. Trying to install pfsense plus. I have the same "efgi_get_Variable: Bad address" problem. Doing the following
load /boot/kernel/kernel
load /boot/kernel/opensolaris.ko
load /boot/kernel/zfs.ko
bootdoesn't get me very far just to a screen of text. I can not access the pfsense webpage. I am not overly familiar with what is going on or why there is an error but I'm pulling my hair out. All I'm trying to do is upgrade my hardware. What is the issue? How do I fix it? How do I know if pfsense is "booting"? What is the screen supposed to show?
-
@doncarajo I should I add I contacted Netgate support as I paid for pfsense plus and they cannot help with protectli hardware. They suggested I run the BIOS in legacy mode but Coreboot doesn't have an option for that. Ideas?
-
@doncarajo Ok. In case anyone needs this in the future. I changed the BIOS from opencore to AMI (https://kb.protectli.com/kb/how-to-use-flashli/) and the installer worked.
-
Do you have output it showed when it failed? It would be good to note some new failure mode if there is one.
-
D doncarajo referenced this topic on
-
@stephenw10 The output was pretty much the same as the original poster, except that doing the additional "load" steps didn't make pfsense boot fully so I couldn't go any further. Everything that I looked up seemed to be pointing to a BIOS issue so that's what made me change it and finally made it work.
-
@doncarajo I am sorry to be butting into your conversation right now but I am experiencing a problem that is virtually identical to the one described at the top of this thread. Unfortunately, my tech skills are rather basic so I am having difficulty with the explanations given. I am trying to install pfSense CE on a brand new Protectli Vault FW4C equipped with Coreboot. I am getting the same error output described above. I apologize that I do not know what most of these terms like EFI and UEFI mean. But, given that my problem seems to be the very same I would very much appreciate careful instructions that a noob like me can follow in order to successfully get pfSense installed. After the bad address messages I cannot get the vault to boot into pfSense and I know next to nothing about editting boot configuration files but I am determined to do what I must for success here. Your assistance would be very much appreciated! Thank you.
-
The root of the issue there is that the Coreboot UEFI implementation does not include the APIs to return the boot variables to the OS when it queries them. The error causes the installer to drop out before it finishes adding the loader values. However you should be able to add them back manually.
Or, as I suggested, you could use the legacy CE installer image which should not be affected.
Steve
-
@stephenw10 Thank you again. I used the legacy installer for 2.7.2 from Dec.8. Everything was going quite well until 2FS Configuration options. I select Stripe-No redundancy then the next screen says only [ ] ada0 Protecli 120GB mSATA. When I click OK the next screen says stripe: Not enough disks selected. (0 < 1 minimum) . I then get the options to Change Selection or Cancel. I can go no further. I'm wondering if the previous unsuccessful installation is interfering with this new one? Please advise me if you can. Thank you.
-
@Bob-Orter Press “space” so that you actually select the drive.
-
That^. You have to select the drive when it shows:
ada0 Protecli 120GB mSATA -
@stephenw10
Perhaps more relevant info. In trying again an earlier 2FS Configuration screen gives the options:Install Proceed with Installation
T Pool Type/Disks: mirror: 0 disks- Rescan Devices *
- Disk Info *
N Pool Name pfSense New
And others....
I renamed to pfSense New because it indicated that pfSense was already being used. Could this be part of the problem? Or that mirror: 0 disks?
-
. Installation seems to be progressing well. I will keep you posted. -
@stephenw10
It appears that the installation has completely successfully! However, upon restarting I am not getting to a pfSense interface. I get a screen with:
Distributions:
Linux Network Installs (64-bit)
Live CDs
...
Tools:
Utilities (UEFI)
iPXE shell
...
What mistake have I made? -
Hmm, that looks like something from Coreboot which implies it's not seeing a bootable device entry.
Can you add an EFI entry with that untility?
Did you choose to install it as UEFI? As I understand it that device will not boot a legacy install.
-
@Bob-Orter You have to manually change the boot order on the coreboot menu so that it boots from the SSD rather than the network tools it defaults to.
