24.11 Upgrade High CPU on 2100 not just the widget

goulou

@stephenw10 Hey Stephen, sorry for the delay, ready to go. In a Shell without the GUI running, top- aSH shows a low of 68.1% and a high of 80.2% over the course of a few minutes without doing anything else at this appliance location. Compared to the same cmd in the GUI which showed CPU: 67.6% user, 4.4% nice, 14.3% system, 1.7% interrupt, 12.0% at that moment.

Obviously regret that I didn't have an established baseline to compare to before/after the upgrade but if asked... based on how fast or slow the GUI previously performed I would have to say that it's much slower now.

Any other cmds to try out via SSH? Thanks!

stephenw10

That seems very high. What does it actually show? What's using the CPU cycles?

For example a test 2100 here shows:

last pid: 84602;  load averages:    0.19,    0.27,    0.28                                                                                                                 up 7+05:03:08  22:50:29
299 threads:   3 running, 273 sleeping, 23 waiting
CPU:  0.2% user,  0.0% nice,  2.1% system,  0.4% interrupt, 97.4% idle
Mem: 57M Active, 423M Inact, 529M Wired, 2290M Free
ARC: 265M Total, 71M MFU, 179M MRU, 16K Anon, 2412K Header, 12M Other
     216M Compressed, 526M Uncompressed, 2.43:1 Ratio

  PID USERNAME    PRI NICE   SIZE    RES STATE    C   TIME    WCPU COMMAND
   11 root        187 ki31     0B    32K CPU0     0 150.8H  98.29% [idle{idle: cpu0}]
   11 root        187 ki31     0B    32K RUN      1 150.7H  97.49% [idle{idle: cpu1}]
    0 root        -12    -     0B   992K -        1  28:54   1.52% [kernel{z_wr_iss}]
   17 root        -16    -     0B    16K mmcsd    0  11:53   0.46% [mmcsd0: mmc/sd card]
51563 root         20    0    14M  4592K CPU1     1   0:00   0.44% top -aSH
    0 root        -16    -     0B   992K -        0  10:18   0.38% [kernel{z_wr_int}]
    7 root        -16    -     0B    16K pftm     0  14:47   0.35% [pf purge]
    2 root        -60    -     0B    32K WAIT     0  27:23   0.16% [clock{clock (0)}]
    6 root         -8    -     0B   720K tx->tx   1   5:25   0.13% [zfskern{txg_thread_enter}]
10651 root         20    0  1299M    70M kqread   0  37:11   0.07% /usr/local/bin/pfnet-controller -conf /var/etc/pfnet-controller/pfnet-controller.conf{pfnet-controller}
   12 root        -64    -     0B   336K WAIT     1   1:40   0.06% [intr{gic0,s26:-ci_xenon0}]
   12 root        -64    -     0B   336K WAIT     0   7:02   0.05% [intr{gic0,s42: mvneta0}]
    6 root         -8    -     0B   720K -        0   1:53   0.05% [zfskern{dp_sync_taskq}]
   14 root         -8    -     0B    48K -        1   1:17   0.05% [geom{g_up}]

goulou

@stephenw10 Yes, I agree and sure, will re-run and post the full output only now trying to SSH in over IPSec since I've left the location. Tried adding a rule like:

Protocol: tcp Source: [my SSH client's IP], Port : any Destination: [remote F/W IP], Port: 22, Interface: IPSec, Action: pass.

My tunnel is otherwise working fine but SSH failing. For destination also tried "this Firewall (self)", "Network" and the F/W's IP ... all a no go to remote SSH over VPN. Thought's on proper syntax for a workable rule for VPN but not over the WAN interface? Thank you.

stephenw10

If it's a tunnel mode IPSec VPN (policy based) you're probably hitting this:
https://docs.netgate.com/pfsense/en/latest/vpn/ipsec/access-firewall-over-ipsec.html

You are able to hit the webgui though? And not seeing blocked ssh traffic in the firewall log?

goulou

@stephenw10 Yep, the GUI is fully accessible over the tunnel and I didn't find a log entry for the remote SSH attempts getting blocked but without going too far into the weeds, I would just leave things as they are until next time I'm at the location. When I can I'll rerun the top cmd w/o a GUI running and post the full output here. Apart from the higher than expected CPU and laggy GUI navigation, everything else appears to be good. I've also upgraded a 6100 and a 4860 with no visible issues.

Also thanks for the documentation accessing F/W services over IPsec, interesting but going to pass on those possible workarounds for now.

ezambran71

I’m experiencing a potentially related issue on my SG-1100 after the upgrade. The dashboard shows constant 100% CPU usage, but it normalized after about 48 hours of continuous operation.

stephenw10

Is that with the modified widget behaviour? Did you have the dashboard open for all that time?

ezambran71

@stephenw10 Yes, these measurements are with the dashboard open the entire time. I had several widgets on the dashboard, including 'Traffic Graphs' set to refresh every 3 seconds. After about 48 hours, the CPU usage stabilized at 75–99%. (I also note that with the dashboard closed the CPU usage drops considerably.)

I’m also running high-demand services like Snort IDS and WireGuard VPN client, so that contributes to the load. However, I feel the new version has definitely increased CPU usage compared to the previous one—I’m using the same configuration, and the CPU usage was noticeably lower before the upgrade.

It seems the modified with more widget behavior combined with the dashboard being open all the time and the overall higher CPU usage in this version might be factors.
Screenshot 2024-12-02 103429.png

stephenw10

It doesn't look like it but do you have MIM enabled?

ezambran71

No, I do not have it activated. The image shows the CPU usage when the dashboard is not on screen. The high CPU usage is only when the dashboard is on screen.