Watchguard Firebox X Peak platform

stephenw10

Thanks for that.
I see my mistake now. I expected bridge0 to be assigned to an interface after I had created it but that's something you have to do manually.
Seems somehow counter-intuitive to me.

Steve

wallabybob

@stephenw10:

I expected bridge0 to be assigned to an interface after I had created it but that's something you have to do manually.

You might be thinking of pfSense 1.2.x way of bridging: when configuring interfaces they could be "bridged" with another interface. The bridging was not always visible and that could result in misleading reports. In particular, if ath0 was bridged with vr0 (or was it the other way around?) a DHCP request on ath0 was reported as received on vr0. Huh, how did the DHCP request from a wireless client get onto a wired interface? (Or, possibly depending on how I had configured the bridging, how did the DHCP request from a wired client get on the wireless interface?)

The 1.2.x way of configuring bridging had a scaling issue in that it wasn't clear how to bridge more than two interfaces.

I like it that in 2.0 the bridging can be made more visible, you can run DHCP server on a bridge interface and it reports DHCP requests on the bridge interface rather than the wrong physical interface.

I haven't tried it, but I suspect it is possible to (say) create a bridge with members ath0 and vr0, assign vr0 to LAN and enable DHCP server on LAN and get the old behaviour. Experience suggests I would come to regret such a choice.

stephenw10

I completely agree the 2.0 way of doing things makes far more sense conceptually.
After I go to Interfaces: (assign): bridges and add a bridge I expected to see that in interfaces but in fact you have to add another interface and assign the bridge to it. There are no clear instructions that set this out and to me it seems unintuitive. Could be just me. ::)

Steve

power_matz

Thank you for the instructions.
After doing all that I see that if the bridge only works if on the interface (re2 in my case) the bridge is assigned is up. If a device on re3 (also a member of the bridge) is the only one then the bridge is offline.
Is the a mistake on my side?

stephenw10

The bridge should be assigned to a non-physical interface such as OPT2. The members of the bridge are the physical interfaces, re2 re3 etc.
That way bridge itself will always appear as UP.

Steve

power_matz

ok, got that.
Do you think one rule for the bridge in the firewall is enough?
I don't have to define for each interface a rule, or?

stephenw10

Have read through the first few posts here: http://forum.pfsense.org/index.php/topic,20917.0.html

As I said above the default settings mean that the firewalling is done on the member interfaces not the bridge.
There are settings in Advanced: System Tunables: to change that. However I seem to remember reading that they may not work any longer. Try it and see. ;)


net.link.bridge.pfil_member 	Set to 0 to disable filtering on the incoming and outgoing member interfaces. 	default (1) 	

net.link.bridge.pfil_bridge 	Set to 1 to enable filtering on the bridge interface 	default (0)

Steve

power_matz

Yes, I read that before and tried it out. It seems that it don't work.
One device on a port in the bridge wants a IP per DHCP and this is blocked by the firewall. So adding the rule worked.

But I will give it another try after a reboot this evening.

stephenw10

Yes you may well have to reboot or at least reload something before those tunables take effect.

Steve

power_matz

OK! ;D
It is (always) as you said. Setting the tunables is working. I needed only some rules for the bridge interface and voila everything is running as I wanted.
Brilliant!
Thank you for your input.

stephenw10

No problem. :)
Hopefully this may prove useful for anyone else searching for bridging.

Steve

shanon

Minor update regarding my challenges booting images later than version 1.2.3 RC1:

I recently acquired a couple of Portwell NAR5060 boxes which are of a somewhat similar age as the Firebox X Peak and share some similar hardware. The good news is that I've got pfSense 2.0.1 nanobsd running on that hardware without modification and I hope to use this to free up the Firebox for bench testing.

I also recently got a mini-PCI VGA card, but I'm only halfway through figuring out its pinout and wiring a cable.

Hope to get a little further tomorrow… work has been busy, so progress is slow unfortunately.

mwp

You ever get the safenet card to work?

moogoom

@stephenw10:

Edit: Anyone reading this: These are instructons are old and overly complex. See this post for a simpler updated solution.

Mostly for my own benefit because I completely hosed my install messing about with ACPI and have to reflash my CF card. ::)
Here's some concise instructions for installing the firebox lcd software.
Download the file with the driver, lcdd3.tar, from here (can't attach it to this post >:()
http://sites.google.com/site/pfsensefirebox/home/lcdd3.tar?attredirects=0
Copy it to the firebox to /var/tmp. This is a folder that only exists in memory and gets wiped at boot. I used WinSCP.
Connect to the box (with putty via ssh or serial or whatever). Then:
[root@pfSense.local]/root(2): cd /var/tmp

[root@pfSense.local]/var/tmp(5): tar -xvf lcdd3.tar
x ./install-embed.lcdd.sh
x ./lcdd/
x ./lcdd/drivers/
x ./lcdd/LCDd.conf
x ./lcdd/lcdd.sh
x ./lcdd/lcdproc
x ./lcdd/LCDd
x ./lcdd/drivers/curses.so
x ./lcdd/drivers/sdeclcd.so
x ./lcdd2.tar

[root@pfSense.local]/var/tmp(7): ./install-embed.lcdd.sh

[root@pfSense.local]/var/tmp(8): cd /lib

[root@pfSense.local]/lib(10): /etc/rc.conf_mount_rw

[root@pfSense.local]/lib(11): ln -s libc.so.7 libc.so.6

[root@pfSense.local]/lib(12): ln -s libkvm.so.4 libkvm.so.3

[root@pfSense.local]/lib(13): /etc/rc.conf_mount_ro

[root@pfSense.local]/lib(14): /usr/local/etc/rc.d/lcdd.sh
And it should all be working! ;)
I have removed a few steps from the other instructions on the forum. I have included the newest driver in the tarball. I found I didn't need to alter the permisions of the install script.
I tested this on a fresh install of the embedded 1.2.3-release.
It will not work on 2.0 beta, I tried! :P

Steve

Edit: It does work in 2.0 you have to sym link both libkvm.so.3 and libkvm.so.4 to libkvm.so.5

I have problem with installation. When I write on terminal: "./install-embed.lcdd.sh", I see: "mount: /dev/ad2s1a : Device busy" … Why I can't install ?

stephenw10

It's because that script was originally written for an embedded install of pfSense 1.2. The embbeded install (and the Nanobsd install) runs with the file system mounted read-only to minimise writes to flash media. The script remounts it as RW, installs the various files and then remounts it RO again. This won't work on a full install that you are running.
Besides that as I wrote at the top it's now very out of date.
Try this post instead. I can't say if that will work any better since it's still writtenb for Nano but I changed it to use the correct mount script rather than attempting to mount the filesystem directly. I have never tried it on a full install.
If that still doesn't work that you can just edit the install script, install3.sh, and remove the remount calls.

Steve