PPPoE on OPT1 – Embedded not working --Blank
-
Running on an Alix 2D3 – 3 NICs. Beta 4.
I have two ADSL connections with PPPoe. The WAN works fine. The OPT1 says it's up, but it's blank...on the interface page:
Status up
PPPoE up
Uptime 00:00:0
MAC address 00:00:00:00:00:00
In/out packets 0/0 (0 bytes/0 bytes)
In/out packets (pass) 0/0 (0 bytes/0 bytes)
In/out packets (block) 0/0 (0 bytes/0 bytes)
In/out errors 0/0
Collisions 0PPP log:
Oct 4 23:22:21 ppp: [opt1] IPADDR 0.0.0.0
Oct 4 23:22:21 ppp: [opt1] PRIDNS 0.0.0.0
Oct 4 23:22:21 ppp: [opt1] SECDNS 0.0.0.0
Oct 4 23:22:21 ppp: [opt1] IPCP: rec'd Configure Nak #2 (Ack-Sent)
Oct 4 23:22:21 ppp: [opt1] IPADDR 79.xx.x.x
Oct 4 23:22:21 ppp: [opt1] 79.xx.xx.xx is OK
Oct 4 23:22:21 ppp: [opt1] PRIDNS 192.xxx.xxx.xx
Oct 4 23:22:21 ppp: [opt1] SECDNS 62.xxx.xxx.xx
Oct 4 23:22:21 ppp: [opt1] IPCP: SendConfigReq #3
Oct 4 23:22:21 ppp: [opt1] IPADDR xx.xx.xx.xx
Oct 4 23:22:21 ppp: [opt1] PRIDNS 192.xx.xx.xx
Oct 4 23:22:21 ppp: [opt1] SECDNS 62.xx.xx.xx
Oct 4 23:22:21 ppp: [opt1] IPCP: rec'd Configure Ack #3 (Ack-Sent)
Oct 4 23:22:21 ppp: [opt1] IPADDR 79.xx.xx.xx
Oct 4 23:22:21 ppp: [opt1] PRIDNS 192.xx.xx.xx
Oct 4 23:22:21 ppp: [opt1] SECDNS 62.xx.xx.xx
Oct 4 23:22:21 ppp: [opt1] IPCP: state change Ack-Sent –> Opened
Oct 4 23:22:21 ppp: [opt1] IPCP: LayerUp
Oct 4 23:22:21 ppp: [opt1] 79.xx.xx.xx -> 212.xx.xx.xx
Oct 4 23:22:21 ppp: [opt1] IFACE: Adding IPv4 address to pppoe1 failed: File exists
Oct 4 23:22:21 ppp: [opt1] IFACE: IfaceChangeAddr() error, closing IPCP
Oct 4 23:22:21 ppp: [opt1] IPCP: parameter negotiation failed
Oct 4 23:22:21 ppp: [opt1] IPCP: state change Opened –> Stopping
Oct 4 23:22:21 ppp: [opt1] IPCP: SendTerminateReq #4
Oct 4 23:22:21 ppp: [opt1] IPCP: LayerDown
Oct 4 23:22:22 ppp: [opt1] IPCP: rec'd Terminate Ack #4 (Stopping)
Oct 4 23:22:22 ppp: [opt1] IPCP: state change Stopping –> Stopped
Oct 4 23:22:22 ppp: [opt1] IPCP: LayerFinish
Oct 4 23:22:22 ppp: [opt1] Bundle: No NCPs left. Closing links…
Oct 4 23:22:22 ppp: [opt1] Bundle: closing link "opt1_link0"…
Oct 4 23:22:22 ppp: [opt1_link0] LCP: rec'd Terminate Request #148 (Opened)
Oct 4 23:22:22 ppp: [opt1_link0] LCP: state change Opened –> Stopping
Oct 4 23:22:22 ppp: [opt1_link0] Link: Leave bundle "opt1"
Oct 4 23:22:22 ppp: [opt1] Bundle: Status update: up 0 links, total bandwidth 9600 bps
Oct 4 23:22:22 ppp: [opt1] IPCP: Close event
Oct 4 23:22:22 ppp: [opt1] IPCP: state change Stopped –> Closed
Oct 4 23:22:22 ppp: [opt1] IPCP: Down event
Oct 4 23:22:22 ppp: [opt1] IPCP: state change Closed –> Initial
Oct 4 23:22:22 ppp: [opt1_link0] LCP: SendTerminateAck #3
Oct 4 23:22:22 ppp: [opt1_link0] LCP: LayerDown
Oct 4 23:22:22 ppp: [opt1_link0] Link: CLOSE event
Oct 4 23:22:22 ppp: [opt1_link0] LCP: Close event
Oct 4 23:22:22 ppp: [opt1_link0] LCP: state change Stopping –> Closing
Oct 4 23:22:23 ppp: [opt1_link0] LCP: rec'd Terminate Request #225 (Closing)
Oct 4 23:22:23 ppp: [opt1_link0] LCP: SendTerminateAck #4
Oct 4 23:22:24 ppp: [opt1_link0] LCP: state change Closing –> Closed
Oct 4 23:22:24 ppp: [opt1_link0] LCP: LayerFinish
Oct 4 23:22:24 ppp: [opt1_link0] Link: DOWN event
Oct 4 23:22:24 ppp: [opt1_link0] LCP: Down event
Oct 4 23:22:24 ppp: [opt1_link0] LCP: state change Closed –> InitialI should add, it works fine using DHCP, but I'd rather not rely on my ADSL modem to do the routing.. :(
-
Are both PPPoE connections to the same ISP?
If you have two lines to the same DSL ISP, you either need MLPPP (must be supported on the ISP side), or an intermediate NAT router like your DSL modem/router.
You can't have two WANs in the same subnet with the same gateway, which is probably why you got that "file exists" error in the log.
-
They're both to the same IP, but one is in in the static IP pool and the other is in the dynamic (which are different subnets); but they both have the same gateway (if that matters..)
-
Yes, that matters, they need different gateways.
