Status-Interfaces (SOLVED)



  • Wan not show mac address and Media..

    Uploaded with ImageShack.us

    Uploaded with ImageShack.us

    ifconfig -a

    
    re0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
    	options=389b <rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum,wol_ucast,wol_mcast,wol_magic>ether 70:71:bc:xx:xx:xx
    	inet6 fe80::7271:bcff:febd:80d4%re0 prefixlen 64 scopeid 0x1 
    	nd6 options=3 <performnud,accept_rtadv>media: Ethernet autoselect (10baseT/UTP <half-duplex>)
    	status: active
    em0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
    	options=209b <rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum,wol_magic>ether 00:07:e9:xx:xx:xx
    	inet 192.168.XX.XX netmask 0xffffff00 broadcast 192.168.XX.255
    	inet6 fe80::207:e9ff:fe10:1bc4%em0 prefixlen 64 scopeid 0x2 
    	nd6 options=3 <performnud,accept_rtadv>media: Ethernet autoselect (100baseTX <full-duplex>)
    	status: active
    lo0: flags=8049 <up,loopback,running,multicast>metric 0 mtu 16384
    	options=3 <rxcsum,txcsum>inet 127.0.0.1 netmask 0xff000000 
    	inet6 ::1 prefixlen 128 
    	inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3 
    	nd6 options=3 <performnud,accept_rtadv>pfsync0: flags=0<> metric 0 mtu 1460
    	syncpeer: 224.0.0.240 maxupd: 128 syncok: 1
    pflog0: flags=100 <promisc>metric 0 mtu 33200
    enc0: flags=0<> metric 0 mtu 1536
    pppoe0: flags=88d1 <up,pointopoint,running,noarp,simplex,multicast>metric 0 mtu 1492
    	inet 190.XX.XX.XX --> 200.40.18.26 netmask 0xffffffff 
    	inet6 fe80::7271:bcff:febd:80d4%pppoe0 prefixlen 64 scopeid 0x7 
    	nd6 options=3 <performnud,accept_rtadv></performnud,accept_rtadv></up,pointopoint,running,noarp,simplex,multicast></promisc></performnud,accept_rtadv></rxcsum,txcsum></up,loopback,running,multicast></full-duplex></performnud,accept_rtadv></rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum,wol_magic></up,broadcast,running,simplex,multicast></half-duplex></performnud,accept_rtadv></rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum,wol_ucast,wol_mcast,wol_magic></up,broadcast,running,simplex,multicast> 
    

    dmesg```
    Copyright (c) 1992-2010 The FreeBSD Project.
    Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
    The Regents of the University of California. All rights reserved.
    FreeBSD is a registered trademark of The FreeBSD Foundation.
    FreeBSD 8.1-RELEASE-p4 #1: Wed Jul 27 13:20:28 EDT 2011
       sullrich@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org:/usr/obj./usr/pfSensesrc/src/sys/pfSense.8 i386
    Timecounter "i8254" frequency 1193182 Hz quality 0
    CPU: Intel(R) Atom(TM) CPU D525   @ 1.80GHz (1800.08-MHz 686-class CPU)
     Origin = "GenuineIntel"  Id = 0x106ca  Family = 6  Model = 1c  Stepping = 10
     Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0x40e31d <sse3,dtes64,mon,ds_cpl,tm2,ssse3,cx16,xtpr,pdcm,movbe>AMD Features=0x20100000 <nx,lm>AMD Features2=0x1 <lahf>TSC: P-state invariant
    real memory  = 2147483648 (2048 MB)
    avail memory = 2065281024 (1969 MB)
    ACPI APIC Table: <intel  d525mw=""  ="">FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
    FreeBSD/SMP: 0 package(s) x 2 core(s) x 2 HTT threads
    cpu0 (BSP): APIC ID:  0
    cpu1 (AP): APIC ID:  2
    WARNING: Non-uniform processors.
    WARNING: Using suboptimal topology.
    ioapic0: Changing APIC ID to 8
    ioapic0 <version 2.0="">irqs 0-23 on motherboard
    lapic0: Forcing LINT1 to edge trigger
    netisr_init: forcing maxthreads to 1 and bindthreads to 0 for device polling
    wpi: You need to read the LICENSE file in /usr/share/doc/legal/intel_wpi/.
    wpi: If you agree with the license, set legal.intel_wpi.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (wpi_fw, 0xc09882e0, 0) error 1
    ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_bss_fw, 0xc0789320, 0) error 1
    ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_ibss_fw, 0xc07893c0, 0) error 1
    ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_monitor_fw, 0xc0789460, 0) error 1
    wlan: mac acl policy registered
    kbd1 at kbdmux0
    cryptosoft0: <software crypto="">on motherboard
    padlock0: No ACE support.
    acpi0: <intel d525mw="">on motherboard
    acpi0: [ITHREAD]
    acpi0: Power Button (fixed)
    Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
    acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
    cpu0: <acpi cpu="">on acpi0
    cpu1: <acpi cpu="">on acpi0
    acpi_hpet0: <high precision="" event="" timer="">iomem 0xfed00000-0xfed003ff on acpi0
    Timecounter "HPET" frequency 14318180 Hz quality 900
    acpi_button0: <sleep button="">on acpi0
    pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0
    pci0: <acpi pci="" bus="">on pcib0
    vgapci0: <vga-compatible display="">port 0x30c0-0x30c7 mem 0xf0300000-0xf037ffff,0xe0000000-0xefffffff,0xf0200000-0xf02fffff irq 16 at device 2.0 on pci0
    agp0: <intel pineview="" svga="" controller="">on vgapci0
    agp0: detected 8188k stolen memory
    agp0: aperture size is 256M
    pcib1: <acpi pci-pci="" bridge="">at device 28.0 on pci0
    pci1: <acpi pci="" bus="">on pcib1
    re0: <realtek 8111="" 8168="" b="" c="" cp="" d="" dp="" e="" pcie="" gigabit="" ethernet="">port 0x2000-0x20ff mem 0xf0004000-0xf0004fff,0xf0000000-0xf0003fff irq 16 at device 0.0 on pci1
    re0: Using 1 MSI messages
    re0: Chip rev. 0x2c000000
    re0: MAC rev. 0x00000000
    miibus0: <mii bus="">on re0
    rgephy0: <rtl8169s 8110s="" 8211b="" media="" interface="">PHY 1 on miibus0
    rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
    re0: [FILTER]
    pcib2: <acpi pci-pci="" bridge="">at device 28.1 on pci0
    pci2: <acpi pci="" bus="">on pcib2
    pcib3: <acpi pci-pci="" bridge="">at device 28.2 on pci0
    pci3: <acpi pci="" bus="">on pcib3
    pcib4: <acpi pci-pci="" bridge="">at device 28.3 on pci0
    pci4: <acpi pci="" bus="">on pcib4
    uhci0: <intel 82801g="" (ich7)="" usb="" controller="" usb-a="">port 0x3080-0x309f irq 23 at device 29.0 on pci0
    uhci0: [ITHREAD]
    uhci0: LegSup = 0x2f00
    usbus0: <intel 82801g="" (ich7)="" usb="" controller="" usb-a="">on uhci0
    uhci1: <intel 82801g="" (ich7)="" usb="" controller="" usb-b="">port 0x3060-0x307f irq 19 at device 29.1 on pci0
    uhci1: [ITHREAD]
    uhci1: LegSup = 0x2f00
    usbus1: <intel 82801g="" (ich7)="" usb="" controller="" usb-b="">on uhci1
    uhci2: <intel 82801g="" (ich7)="" usb="" controller="" usb-c="">port 0x3040-0x305f irq 18 at device 29.2 on pci0
    uhci2: [ITHREAD]
    uhci2: LegSup = 0x2f00
    usbus2: <intel 82801g="" (ich7)="" usb="" controller="" usb-c="">on uhci2
    uhci3: <intel 82801g="" (ich7)="" usb="" controller="" usb-d="">port 0x3020-0x303f irq 16 at device 29.3 on pci0
    uhci3: [ITHREAD]
    uhci3: LegSup = 0x2f00
    usbus3: <intel 82801g="" (ich7)="" usb="" controller="" usb-d="">on uhci3
    ehci0: <intel 82801gb="" r="" (ich7)="" usb="" 2.0="" controller="">mem 0xf0380400-0xf03807ff irq 23 at device 29.7 on pci0
    ehci0: [ITHREAD]
    usbus4: EHCI version 1.0
    usbus4: <intel 82801gb="" r="" (ich7)="" usb="" 2.0="" controller="">on ehci0
    pcib5: <acpi pci-pci="" bridge="">at device 30.0 on pci0
    pci5: <acpi pci="" bus="">on pcib5
    em0: <intel(r) 1000="" pro="" legacy="" network="" connection="" 1.0.3="">port 0x1000-0x103f mem 0xf0120000-0xf013ffff,0xf0100000-0xf011ffff irq 20 at device 0.0 on pci5
    em0: [FILTER]
    isab0: <pci-isa bridge="">at device 31.0 on pci0
    isa0: <isa bus="">on isab0
    atapci0: <intel ich7="" sata300="" controller="">port 0x30b8-0x30bf,0x30cc-0x30cf,0x30b0-0x30b7,0x30c8-0x30cb,0x30a0-0x30af mem 0xf0380000-0xf03803ff irq 18 at device 31.2 on pci0
    atapci0: [ITHREAD]
    atapci0: AHCI called from vendor specific driver
    atapci0: AHCI v1.10 controller with 4 3Gbps ports, PM not supported
    ata2: <ata 0="" channel="">on atapci0
    ata2: [ITHREAD]
    ata3: <ata 1="" channel="">on atapci0
    ata3: [ITHREAD]
    pci0: <serial bus,="" smbus="">at device 31.3 (no driver attached)
    atrtc0: <at realtime="" clock="">port 0x70-0x71,0x74-0x77 irq 8 on acpi0
    uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
    uart0: [FILTER]
    uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
    uart1: [FILTER]
    pmtimer0 on isa0
    orm0: <isa option="" roms="">at iomem 0xce000-0xcefff,0xcf000-0xcffff pnpid ORM0000 on isa0
    sc0: <system console="">at flags 0x100 on isa0
    sc0: VGA <16 virtual consoles, flags=0x300>
    vga0: <generic isa="" vga="">at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
    ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
    ata0: [ITHREAD]
    ata1 at port 0x170-0x177,0x376 irq 15 on isa0
    ata1: [ITHREAD]
    atkbdc0: <keyboard controller="" (i8042)="">at port 0x60,0x64 on isa0
    atkbd0: <at keyboard="">irq 1 on atkbdc0
    kbd0 at atkbd0
    atkbd0: [GIANT-LOCKED]
    atkbd0: [ITHREAD]
    ppc0: parallel port not found.
    p4tcc0: <cpu frequency="" thermal="" control="">on cpu0
    p4tcc1: <cpu frequency="" thermal="" control="">on cpu1
    RTC BIOS diagnostic error 80 <clock_battery>Timecounters tick every 1.000 msec
    IPsec: Initialized Security Association Processing.
    usbus0: 12Mbps Full Speed USB v1.0
    usbus1: 12Mbps Full Speed USB v1.0
    usbus2: 12Mbps Full Speed USB v1.0
    usbus3: 12Mbps Full Speed USB v1.0
    usbus4: 480Mbps High Speed USB v2.0
    ad4: 152627MB <samsung hd161hj="" jf100-19="">at ata2-master UDMA100 SATA 3Gb/s
    ugen0.1: <intel>at usbus0
    uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
    ugen1.1: <intel>at usbus1
    uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
    ugen2.1: <intel>at usbus2
    uhub2: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus2
    ugen3.1: <intel>at usbus3
    uhub3: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus3
    ugen4.1: <intel>at usbus4
    uhub4: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus4
    lapic2: Forcing LINT1 to edge trigger
    SMP: AP CPU #1 Launched!
    Root mount waiting for: usbus4 usbus3 usbus2 usbus1 usbus0
    uhub0: 2 ports with 2 removable, self powered
    uhub1: 2 ports with 2 removable, self powered
    uhub2: 2 ports with 2 removable, self powered
    uhub3: 2 ports with 2 removable, self powered
    Root mount waiting for: usbus4
    Root mount waiting for: usbus4
    Root mount waiting for: usbus4
    uhub4: 8 ports with 8 removable, self powered
    Trying to mount root from ufs:/dev/ad4s1a
    pflog0: promiscuous mode enabled
    em0: link state changed to UP
    re0: link state changed to UP
    pid 7207 (squid), uid 62: exited on signal 6</intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></samsung></clock_battery></cpu></cpu></at></keyboard></generic></system></isa></at></serial></ata></ata></intel></isa></pci-isa></intel(r)></acpi></acpi></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></acpi></acpi></acpi></acpi></acpi></acpi></rtl8169s></mii></realtek></acpi></acpi></intel></vga-compatible></acpi></acpi></sleep></high></acpi></acpi></intel></software></version></intel></lahf></nx,lm></sse3,dtes64,mon,ds_cpl,tm2,ssse3,cx16,xtpr,pdcm,movbe></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>

    
    http://standards.ieee.org/develop/regauth/oui/oui.txt


  • I am using 2.0-RC3 (amd64) built on Thu Jul 28 05:40:09 EDT 2011 and I can see MAC addresses.


  • Rebel Alliance Developer Netgate

    Your WAN is PPPoE. A PPPoE interface is a virtual interface that has no MAC address.



  • ok jimp, thanks.


Locked