PfBlocker

LEPM

Increase even more Firewall Maximum Table Entries in system->advanced -> firewall/NAT

not!!!! Firewall Maximum States ;)

marcelloc

PfBlocker use url tables, so it is firewall maximum table entries for sure.

Firewall maximum states are related to active connections. When you reach this value, you can't do anything on firewall.

taryezveb

After trying out a few things all is fine for now. Disabled the TBG List and left the Bluetack enabled. Also in System -> Advanced -> Firewall and NAT; Firewall Maximum Table Entries, removed that large number[9999999999999999] from there. Restarted pfBlocker and now there are no error messages and Squid works as transparent proxy, even with pfBlocker enabled. So it seems the TBG list is the cause of all these issues I was having.

TBG list:

http://list.iblocklist.com/?list=ijfqtofzixtwayqovmxn&fileformat=p2p&archiveformat=gz
http://list.iblocklist.com/?list=ecqbsykllnadihkdirsh&fileformat=p2p&archiveformat=gz
http://list.iblocklist.com/?list=tbnuqfclfkemqivekikv&fileformat=p2p&archiveformat=gz
http://list.iblocklist.com/?list=ewqglwibdgjttwttrinl&fileformat=p2p&archiveformat=gz

Bluetack list:

http://list.iblocklist.com/?list=bt_level1&fileformat=p2p&archiveformat=gz
http://list.iblocklist.com/?list=bt_level2&fileformat=p2p&archiveformat=gz
http://list.iblocklist.com/?list=bt_level3&fileformat=p2p&archiveformat=gz
http://list.iblocklist.com/?list=bt_ads&fileformat=p2p&archiveformat=gz
http://list.iblocklist.com/?list=bt_spyware&fileformat=p2p&archiveformat=gz
http://list.iblocklist.com/?list=bt_proxy&fileformat=p2p&archiveformat=gz
http://list.iblocklist.com/?list=bt_templist&fileformat=p2p&archiveformat=gz
http://list.iblocklist.com/?list=bt_hijacked&fileformat=p2p&archiveformat=gz
http://list.iblocklist.com/?list=bt_dshield&fileformat=p2p&archiveformat=gz
http://list.iblocklist.com/?list=bt_bogon&fileformat=p2p&archiveformat=gz

marcelloc

You may try if you want add each TBG list until you find what list get errors.

taryezveb

@marcelloc:

You may try if you want add each TBG list until you find what list get errors.

Yes, I'm going to try that. I might spring for the i-block lists, need to do some research on that. Are the i-block lists any better than the public lists?

taryezveb

Did some testing.

With the following in the TBG list, whenever I try to enable them[one at a time], get the Fatal error below.

http://list.iblocklist.com/?list=ijfqtofzixtwayqovmxn&fileformat=p2p&archiveformat=gz
http://list.iblocklist.com/?list=ecqbsykllnadihkdirsh&fileformat=p2p&archiveformat=gz

Fatal error: Allowed memory size of 134217728 bytes exhausted (tried to allocate 8650655 bytes) in /usr/local/pkg/pfblocker.inc on line 268

Note, the Bluetack list is still enabled. When testing the above.

marcelloc

the total download exceeds php memory limit.

try to apply one list at time

taryezveb

@marcelloc:

the total download exceeds php memory limit.

try to apply one list at time

@taryezveb:

whenever I try to enable them[one at a time]

I did, or do you mean something else?

marcelloc

I mean that. Sorry, I didn't saw the "[one at a time]"

taryezveb

@marcelloc:

I mean that. Sorry, I didn't saw the "[one at a time]"

No problem and guess no more lists for me :(

marcelloc

The are some file hacks to increase php memory limit, but it is not supported or recommended by core team.

DO IT AT YOUR OWN RISK

edit ini_set("memory_limit","128M"); to 500M in /etc/inc/config.inc file

and include ini_set('memory_limit', '490M'); on pfblocker.inc

Do not increase it to a value greater then 510M, suhosin.memory_limit is set to 512M

taryezveb

@marcelloc:

edit ini_set("memory_limit","128M"); to 500M in /etc/inc/config.inc file

and include ini_set('memory_limit', '490M'); on pfblocker.inc

Do not increase it to a value greater then 510M, suhosin.memory_limit is set to 512M

I take it a reboot is needed for these changes to take affect?

marcelloc

Not at all. There is no changes on php.ini

taryezveb

Hmm, I edited the following to test:

/etc/inc/config.inc and changed ini_set("memory_limit","128M"); to 500M

/usr/local/pkg/pfblocker.inc and added ini_set('memory_limit', '490M');

Then tried to enable the TBG list, but still get the Fatal error. Did I do something wrong?

marcelloc

Not sure, I did it on a x64 virtual machine and I do not get php limit errors.

All files are uploaded.

EDIT

With all these large files, my virtual machine gets 100% cpu for more then a minute and even with a very large table size, it reach virtual machine memory limit (384Mb).

marcelloc

Something interesting about table-entries limit:

I've set up maximum table entries to a very high value 99999999999 at gui and could see it reflected on /tmp/rules.debug

BUT

on pfctl -sa I get this:
LIMITS:
states hard limit 1000000
src-nodes hard limit 1000000
frags hard limit 5000
tables hard limit 1000
table-entries hard limit 1215752191

I saw my virtual machine freezing console with 99999999999 value, so I reduced it on gui to 5000000

EDIT

After 2G RAM, Firewall Maximum Table Entries set to 5000000 and a reboot

I get no erros with both large lists applied

as x64 version already has ini_set("memory_limit","256M");, I've just included ini_set('memory_limit', '250M'); on line two of /usr/local/pkg/pfblocker.inc

taryezveb

@marcelloc:

Something interesting about table-entries limit:

I've set up maximum table entries to a very high value 99999999999 at gui and could see it reflected on /tmp/rules.debug

BUT

on pfctl -sa I get this:
LIMITS:
states hard limit 1000000
src-nodes hard limit 1000000
frags hard limit 5000
tables hard limit 1000
table-entries hard limit 1215752191

I saw my virtual machine freezing console with 99999999999 value, so I reduced it on gui to 5000000

EDIT

After 2G RAM, Firewall Maximum Table Entries set to 5000000 and a reboot

I get no erros with both large lists applied

as x64 version already has ini_set("memory_limit","256M");, I've just included ini_set('memory_limit', '250M'); on line two of /usr/local/pkg/pfblocker.inc

Interesting, and yes when I edited /etc/inc/config.inc I saw it already had ini_set("memory_limit","256M"); . I have a x64 install. Nevertheless when I get a chance I will try your last settings again and reboot. Thanks for the info.

taryezveb

@marcelloc:

EDIT

After 2G RAM, Firewall Maximum Table Entries set to 5000000 and a reboot

I get no erros with both large lists applied

as x64 version already has ini_set("memory_limit","256M");, I've just included ini_set('memory_limit', '250M'); on line two of /usr/local/pkg/pfblocker.inc

Yes! :) I tested the above and no more errors, sort of; I'll explain below.

I did the following:

Edited /usr/local/pkg/pfblocker.inc adding the following on the first line where the comments end[from the top]. Right after this line:
*/ <- this is line number 31
ini_set("memory_limit", "250M"); <- this would be line number 32

Then set the Firewall Maximum Table Entries: 5000000 and did a reboot. But received these errors:
Dec 31 18:13:44 php: : There was an error while parsing the package filter rules for /usr/local/pkg/squid.inc.

Dec 31 18:13:44 php: : The command '/sbin/pfctl -nf /tmp/rules.test.packages' returned exit code '1', the output was 'no IP address found for 550.164.3.166/32 /tmp/rules.test.packages:17: file "/var/db/aliastables/pfBlockerBluetack.txt" contains bad data'

After some testing those errors are due to using the following list:
http://list.iblocklist.com/?list=bt_proxy&fileformat=p2p&archiveformat=gz

NOTE: I tried several times removing and adding that list, with the same result.

Once I removed that list I got this:
Dec 31 18:46:28 php: : The command '/sbin/pfctl -o basic -f /tmp/rules.debug' returned exit code '1', the output was 'no IP address found for 75.35.185. /tmp/rules.debug:19: file "/var/db/aliastables/pfBlockerTBG.txt" contains bad data no IP address found for ÿ0.0.0.0/8 /tmp/rules.debug:95: file "/etc/bogons" contains bad data pfctl: Syntax error in config file: pf rules not loaded'

More testing and the error above was due to this list:
http://list.iblocklist.com/?list=bt_level1&fileformat=p2p&archiveformat=gz

But this time after removing the list above and re-adding the error went away. I guess there are some issues with those lists. Will try to contact the author to see if that can be fixed.

So in the end, no more errors and Squid works as a transparent proxy using pfBlocker as well now :)

For reference these are the lists that I'm currently using error free:

<pfblockerlists><config><aliasname>Bluetack</aliasname>

<row><format>gz</format>
<url>http://list.iblocklist.com/?list=bt_level1&fileformat=p2p&archiveformat=gz</url></row>
<row><format>gz</format>
<url>http://list.iblocklist.com/?list=bt_level2&fileformat=p2p&archiveformat=gz</url></row>
<row><format>gz</format>
<url>http://list.iblocklist.com/?list=bt_level3&fileformat=p2p&archiveformat=gz</url></row>
<row><format>gz</format>
<url>http://list.iblocklist.com/?list=bt_ads&fileformat=p2p&archiveformat=gz</url></row>
<row><format>gz</format>
<url>http://list.iblocklist.com/?list=bt_spyware&fileformat=p2p&archiveformat=gz</url></row>
<row><format>gz</format>
<url>http://list.iblocklist.com/?list=bt_templist&fileformat=p2p&archiveformat=gz</url></row>
<row><format>gz</format>
<url>http://list.iblocklist.com/?list=bt_hijacked&fileformat=p2p&archiveformat=gz</url></row>
<row><format>gz</format>
<url>http://list.iblocklist.com/?list=bt_dshield&fileformat=p2p&archiveformat=gz</url></row>
<row><format>gz</format>
<url>http://list.iblocklist.com/?list=bt_bogon&fileformat=p2p&archiveformat=gz</url></row>
<action>Deny_Inbound</action>
<cron>EveryDay</cron></config>
<config><aliasname>TBG</aliasname>

<row><format>gz</format>
<url>http://list.iblocklist.com/?list=ijfqtofzixtwayqovmxn&fileformat=p2p&archiveformat=gz</url></row>
<row><format>gz</format>
<url>http://list.iblocklist.com/?list=ecqbsykllnadihkdirsh&fileformat=p2p&archiveformat=gz</url></row>
<row><format>gz</format>
<url>http://list.iblocklist.com/?list=tbnuqfclfkemqivekikv&fileformat=p2p&archiveformat=gz</url></row>
<row><format>gz</format>
<url>http://list.iblocklist.com/?list=ewqglwibdgjttwttrinl&fileformat=p2p&archiveformat=gz</url></row>
<action>Deny_Inbound</action>
<cron>EveryDay</cron></config></pfblockerlists>

I would like to Thank marcelloc for his time looking into this. A donation was made[yesterday, before marcelloc posted the fix]; will donate again when I can. Hope this change is added to the package for all to benefit, after a few more days of testing. To make sure this change does not affect anything else.

EDIT: Happy New Year :)

marcelloc

Thanks ;D. Did you mentioned these packages developers on donation?

taryezveb

@marcelloc:

Did you mentioned these packages developers on donation?

Yes, I broke it down on how the donation should broken up. Like so: $XX for the X package maintainer(s).