Watchguard XTM 5 Series
-
@stephenw10
ok i will flash the card F with last pfsense
with pfsense : boot stuck at :
em5: <Intel(R) PRO/1000 Network Connection 7.6.1-k> port 0xac00-0xac1f mem 0xfe7e0000-0xfe7fffff,0xfe7dc000-0xfe7dffff irq 17 at device 0.0 on pci2 : solved.
same issue :
[2.4.3-RELEASE][root@pfSense.localdomain]/root: pkg update Updating pfSense-core repository catalogue... pkg: Repository pfSense-core load error: access repo file(/var/db/pkg/repo-pfSense-core.sqlite) failed: No such file or directory Certificate verification failed for /C=GB/ST=Greater Manchester/L=Salford/O=Sectigo Limited/CN=Sectigo RSA Domain Validation Secure Server CA 34405266376:error:14090086:SSL routines:ssl3_get_server_certificate:certificate verify failed:/builder/ce-243/tmp/FreeBSD-src/crypto/openssl/ssl/s3_clnt.c:1269: pkg: https://pkg.pfsense.org/pfSense_v2_4_3_amd64-pfSense_v2_4_3/packagesite.txz: Authentication error Unable to update repository pfSense Error updating repositories! -
This is really a 'thank-you' to those forum contributors who did all the heavy lifting
investigating this box and getting pfSense running with all the hardware whistles & bells configured.After lurking for a few weeks and on this thread and others concerning the XTM 5 series, I took the
plunge and bought one from eBay for £45 for my home setup.I installed the latest pfSense 2.4.5 on a ZFS mirror with two cheapo 120 Gb SSDs, flashed the
BIOS with xtm5_83.rom without any drama, and had no problems accessing the BIOS screens with a
serial cable. The 4G RAM upgrade and E5700 CPU upgrade also went without a hitch.I built a 64 bit WGXepc binary from source in a FreeBSD 11.3 VM (the base for pfSense 2.4.5)
and the Arm/Disarm light now does whatever I tell it to via ShellCmd.Flush with success I splashed out £12 on an Intel Q8200S on eBay and that arrived last week
and I finally hit my first hurdle - the board doesn't boot with this chip, but will if I
reinsert the E5700. So I just wanted to check that others have got this processor working with
the xtm5_83.rom image? It's no real hardship if I can't get it working, it may just be a dudd
Chinese-scavenged chip, but it would be the icing on the cake if I could get it going.Also - following the mantra of 'hope for success, plan for failure', I couldn't find the pinout of the SPI
header anywhere in the forums, even though it was mentioned a few times. As I'm putting together a duplicate box
for my brother this might come in handy, (though hopefully not). I've searched and googled but found nothing.
Can anyone help with this info?Once again - thanks to everyone.
-
It should work with the Q8200S. The board seems very accommodating in general. https://forum.netgate.com/post/427056 and https://forum.netgate.com/post/544654
After camping ebay (for literally years
) I have a Xeon L3110 in mine and that runs great.The SPI pinout is standard as far as I know. From the FW-7581 manual though:
Steve
-
@stephenw10 Outstanding! Thanks for the info.
-
Hi,
Sorry to disturbe the subject.
I have bought a WatchGuard XTM 505 and I will change the processor and the RAM.
About the processor, I have found a Pentium Dual Core E5300, does it fit with the XTM 505 ? Will it works?
For the RAM, I read that we can add up to 8Go but I think 4Go is adequate ?
I want to use all links at Gigabit speed, I have fiber that provide me 990mb/s download and 600mb/s in upload.
I will add an SSD with PFSense.
Do you think my config is good?
Thanks!
-
Yes, it probably will work. Yes it will pass Gigabit line rate (941Mbps) but it will be quite taxed doing so. I would just get an E7500 C2D as they cost peanuts these days unless you already have the E5300 in which case test it and see.
4GB is enough for almost everything sane in that level of device. I never bothered putting more than 2GB in mine. I still use it for testing stuff on occasion.
Steve
-
Ok thanks! I have ordered an E7500 and 4Go DDR2 800.
I currently have a PFSense running in old stuff, with an SSD. Can I just take the SSD to the Watchguard ? or it would be better to make a fresh install ? My old stuff just has 3 gigabit ports so if I just move the SSD I guess I just have to re-configure network interface?
Thanks
-
Yes you would need to reconfigure the interfaces if they are not em in the previous box.
Yes you could just move the SSD. If the previous device does not have a serial console be sure to enable that in Sys > Adv > Admin Access before moving it.
A fresh install is probably a good idea. You will have to boot from CF though unless/until you have swapped out the BIOS to allow USB booting.
Steve
-
I see. Thanks for the help, I think I will make a fresh install :)
-
So..... I took my retired XTM5 box to a radio site (some weeks ago) and have it behind a Cradlepoint doing camera duty nowadays..
If I try to use the gig ports to connect to the Cradlepoint.. if the Cradlepoint goes down for any reason such as a DHCP address change then the ports on the box will flap leaving me unable to reach it. Im 60 miles away and connected via openvpn.
If I use the 100/10 port then Im fine. Since my top speeds via Verizon are less than 20/15 this port is fine for a WAN.
It has always flapped under certain criteria I was never in a position to run down. It was a primary box while here and it did not happen very often.
But it makes me wonder if the flapping is a driver issue. I installed the latest 2.5 snapshot while I was on site today and will test that at some point but seems fishy to me.
-
Hmm, weird. On all the em ports?
Can you set a fixed speed/duplex to avoid it?
Steve
-
Ill try that next time Im up there. Im risking a snapshot update right now to see if I can break it again. Ill be up there before the end of the week anyways so can rescue it if need be. And it came back up fine.
Ill wait till I get up there and switch back to em0 and play with it there.
-
Just got my XTM 5 series today. Installed pfSense 2.4.5 to an SSD. I did it with the VGA. Should I have used console?
Booting with the console cable I get it halting at Auto Detecting?
Is this when I unplug the cable, plug it back in, and should see pfSense booting?
New screen I was able to get to, but can't send F1 or F2
-
You would have to enable the serrial console or install from the serial console image (where it's enabled by default) to see output on the serial console. Though you would normally see some output from the bootloader there if it was trying to boot.
I assume you installed in something else and then moved the drive across?
What image, exactly, did you use to install from?You still have the original BIOS it looks like?
Steve
-
@stephenw10 I still have the original bios.
I installed version 2.4.5-p1 AMD64 USB VGA on another computer and moved the drive.
I tried installing 2.4.5-p1 AMD64 USB Serial to the SSD, but don't see any video output and don't think that computer has serial. -
Ok, did you enable the serial console in System > Advanced > Admin Access on the other device before moving it? If not try swapping it back and doing that first.
The other way to do this is to write the serial install image to CF card, the XTM5 will boot from that with the standard BIOS and you can then install to SSD directly at the serial console.
Steve
-
@stephenw10 Just wrote the console image to the CF card and now it shows up in console but looks stuck here:
-
Are you sure you used the serial console image? That's one of the last things you would see on dual consoles before it switches to serial as primary console only.
It could be an issue with that SSD. Does it boot further if you disconnect it?
Steve
-
@stephenw10
I flashed the console version the 1GB CF card and it will boot without the SSD attached.
When I attach the SSD I get the following interuption in the console and can't go back to the install process.
I did install again to the SSD via my PC with the VGA version and set System > Advanced > Admin Access.
On my desktop I have to change to IDE from ACHI.
For Partition scheme, I tried to do MBR but then my desktop couldn't boot from the ssd.
So I set it up with GPT, but maybe the WatchGuard can't boot from this.
-
It's not a UEFI bios, MBR should work.
So it only boots as far as the installer menu if you boot without the SSD attached?
SATA is not hot-plugable like that I would not expect that to work. However it looks like there is low level issue with that SSD for some reason, which is odd since the one I have has worked with pretty much everything I've thrown at it! Can you try a different SATA device?
Steve
