Useful 3G modem 'mode switching' script
-
Ah OK, that is a collection of data for all supported modems rather than something specific to yours.
Does that not get installed with the port anyway?
I'm going to have to do some reading/testing…..Steve
-
Hmm OK so it looks like under Linux usb_modeswitch ties into the usb subsystem and will automatically recognise devices as they are plugged in and switch them. FreeBSD has a completely different system so none of the automatic part is included in the port.
In FreeBSD you will have to call it manually either with the required parameters in the command line or pointing at a file that contains them.
That's not a problem we can easily make the script run at boot time.So what is your modem? Specifically what are the VID and PID?
Steve
-
That doesnt sound too painful, the script would need to be called at startup before pfSense did its ppp dial.
My modem is a ZTE 636, i also have a Huawei E220 and vodafone K3565 for further testing. Im away til Sunday so dont have access to my test environment but im still checking the forum via my iPhone :-)
-
Ok, to confirm we really need the VID and PID but according to the device_reference.txt:
ZTE MF622 (aka "Onda MDC502HS")
ZTE MF626
ZTE MF628+ (tested version from Telia / Sweden)
ZTE MF633
ZTE MF636 (aka "Telstra / BigPond 7.2 Mobile Card")
ZTE MF637
and probably others not listed here
Contributor: Joakim Wennergren and others
DefaultVendor= 0x19d2
DefaultProduct= 0x2000TargetVendor= 0x19d2
TargetProduct= 0x0031MessageContent="5553424312345678000000000000061e000000000000000000000000000000"
MessageContent2="5553424312345679000000000000061b000000020000000000000000000000"NeedResponse=1
It says to not use the reference file directly, perhaps because it's quite large, so create a new file with the above lines in. Hope! ;)
Steve
-
Cheers Steve, it kinda makes sense now! Were you able to find more documentation on the port, i.e you mentioned that a manual approach is required for FreeBSD, did you read this somewhere or is this from your own knowledge?
I'll do some testing on Sunday and report back here :-)
-
I just looked at what files are installed from the port and it's very few. Only the usb_modeswitch binary and a conf file for disabling it entirely.
Unless I'm missing something.I too have a Huawei K3565. It's not listed but I bet someone has the data for it. Anyway here's an example of how to find the VIP and PID:
[2.0.1-RELEASE][root@pfsense.fire.box]/dev(21): usbconfig ugen0.1: <uhci root="" hub="" intel="">at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON ugen1.1: <uhci root="" hub="" intel="">at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON ugen2.1: <ehci root="" hub="" intel="">at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON ugen2.2: <huawei mobile="" huawei="" technology="">at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON [2.0.1-RELEASE][root@pfsense.fire.box]/dev(22): usbconfig -d 2.2 dump_device_desc ugen2.2: <huawei mobile="" huawei="" technology="">at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON bLength = 0x0012 bDescriptorType = 0x0001 bcdUSB = 0x0200 bDeviceClass = 0x0000 bDeviceSubClass = 0x0000 bDeviceProtocol = 0x0000 bMaxPacketSize0 = 0x0040 idVendor = 0x12d1 idProduct = 0x1001 bcdDevice = 0x0000 iManufacturer = 0x0002 <huawei technology="">iProduct = 0x0001 <huawei mobile="">iSerialNumber = 0x0000 <no string="">bNumConfigurations = 0x0001</no></huawei></huawei></huawei></huawei></ehci></uhci></uhci>
Steve
Edit: It is listed just as the E169.
-
Yes, i think K3565 is just the Vodafone model number, its actually an E169 underneath. Have you managed to get it to switch?
-
Nope! ::)
[2.0.1-RELEASE][root@pfsense.fire.box]/dev(24): usb_modeswitch -c /tmp/e169.txt Looking for target devices ... No devices in target mode or class found Looking for default devices ... found matching product ID No devices in default mode found. Nothing to do. Bye. [2.0.1-RELEASE][root@pfsense.fire.box]/dev(25): cat /tmp/e169.txt # Huawei E169 and others # # Contributor: Dale Lane DefaultVendor= 0x12d1 DefaultProduct= 0x1001 TargetClass= 0xff # choose one of these: HuaweiMode=1
Steve
Edit: Seems to be because it's already in the target class (0xff):
Looking for target devices ... No devices in target mode or class found Looking for default devices ... searching devices, found USB ID 12d1:1001 found matching vendor ID found matching product ID target class ff matching not adding device searching devices, found USB ID 0000:0000 searching devices, found USB ID 0000:0000 searching devices, found USB ID 0000:0000 No devices in default mode found. Nothing to do. Bye.
Possibly already switched? :-\
Doh! looks like E169 is already a supported modem. ::)
-
Looks that way, your console output when you plug the device in doesnt say that its a SCSI device so its already switched!
-
Yep, already works fine.
[2.0.1-RELEASE][root@pfsense.fire.box]/root(1): cu -l cuaU0.0 -s 115200 Connected at OK at I0 Manufacturer: huawei Model: K3565 Revision: 11.608.10.51.00 IMEI: 359574032708530 +GCAP: +CGSM,+DS,+ES OK
Steve
-
I'll give the ZTE a try on Sunday, ive tried this modem previously with pfSense and failed because it is definately seen as a storage device. Will report back with my results.
-
You might think that but here is the system log from when I plugged it in:
Feb 17 18:16:17 pfsense kernel: ugen2.2: <huawei technology="">at usbus2 Feb 17 18:16:17 pfsense kernel: ugen2.2: <huawei technology="">at usbus2 (disconnected) Feb 17 18:16:24 pfsense kernel: ugen2.2: <huawei technology="">at usbus2 Feb 17 18:16:24 pfsense kernel: u3g0: <huawei 0="" 2="" technology="" huawei="" mobile,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr="">on usbus2 Feb 17 18:16:24 pfsense kernel: u3g0: Found 3 ports. Feb 17 18:16:24 pfsense kernel: umass0: <huawei 0="" 2="" technology="" huawei="" mobile,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr="">on usbus2 Feb 17 18:16:26 pfsense kernel: umass1: <huawei 0="" 2="" technology="" huawei="" mobile,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr="">on usbus2 Feb 17 18:16:26 pfsense kernel: (probe0:umass-sim0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 Feb 17 18:16:26 pfsense kernel: (probe0:umass-sim0:0:0:0): CAM status: SCSI Status Error Feb 17 18:16:26 pfsense kernel: (probe0:umass-sim0:0:0:0): SCSI status: Check Condition Feb 17 18:16:26 pfsense kernel: (probe0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present) Feb 17 18:16:26 pfsense kernel: cd0 at umass-sim0 bus 0 scbus0 target 0 lun 0 Feb 17 18:16:26 pfsense kernel: cd0: <huawei mass="" storage="" 2.31="">Removable CD-ROM SCSI-2 device Feb 17 18:16:26 pfsense kernel: cd0: 40.000MB/s transfers Feb 17 18:16:26 pfsense kernel: cd0: Attempt to query device size failed: NOT READY, Medium not present Feb 17 18:16:27 pfsense kernel: (probe0:umass-sim1:1:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 Feb 17 18:16:27 pfsense kernel: (probe0:umass-sim1:1:0:0): CAM status: SCSI Status Error Feb 17 18:16:27 pfsense kernel: (probe0:umass-sim1:1:0:0): SCSI status: Check Condition Feb 17 18:16:27 pfsense kernel: (probe0:umass-sim1:1:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present) Feb 17 18:16:27 pfsense kernel: da0 at umass-sim1 bus 1 scbus1 target 0 lun 0 Feb 17 18:16:27 pfsense kernel: da0: <huawei mmc="" storage="" 2.31="">Removable Direct Access SCSI-2 device Feb 17 18:16:27 pfsense kernel: da0: 40.000MB/s transfers Feb 17 18:16:27 pfsense kernel: da0: Attempt to query device size failed: NOT READY, Medium not present</huawei></huawei></huawei></huawei></huawei></huawei></huawei></huawei>
It clearly comes up as a CD-ROM drive (cd0) and the micro SD reader (da0).
But u3g also shows 'found 3 ports' and looking in /dev there are cuaU0.0 1.1 and 2.2.
I haven't actually tried using this as a modem though, I'm not sure I have a simcard that can do it.Steve
-
We have some progress….
Fresh install of 2.0.1 full on an old Celeron box to avoid mapping USB devices through to a VMWare VM.
Modem is a ZTE MF112Here's what happens initially when plugging the modem in (not using modeswitch)
Feb 19 15:55:56 pfSense kernel: umass0: <zte,incorporated 0="" 2="" zte="" wcdma="" technologies="" msm,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr="">on usbus3 Feb 19 15:55:56 pfSense kernel: umass0: SCSI over Bulk-Only; quirks = 0x0000 Feb 19 15:55:57 pfSense kernel: umass0:0:0:-1: Attached to scbus0 Feb 19 15:55:57 pfSense kernel: (probe0:umass-sim0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 Feb 19 15:55:57 pfSense kernel: (probe0:umass-sim0:0:0:0): CAM status: SCSI Status Error Feb 19 15:55:57 pfSense kernel: (probe0:umass-sim0:0:0:0): SCSI status: Check Condition Feb 19 15:55:57 pfSense kernel: (probe0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present) Feb 19 15:55:57 pfSense kernel: cd0 at umass-sim0 bus 0 scbus0 target 0 lun 0 Feb 19 15:55:57 pfSense kernel: cd0: <hspa usb="" scsi="" cd-rom="" 2.31="">Removable CD-ROM SCSI-2 device Feb 19 15:55:57 pfSense kernel: cd0: 40.000MB/s transfers Feb 19 15:55:57 pfSense kernel: cd0: Attempt to query device size failed: NOT READY, Medium not present</hspa></zte,incorporated>
No interfaces are available to assign under PPP.
I then install the port and create a config file for the MF112 and run modeswitch
Looking for target devices ... No devices in target mode or class found Looking for default devices ... found matching product ID adding device Found device in default mode, class or configuration (1) Accessing device 005 on bus 000 ... Getting the current device configuration ... OK, got current device configuration (1) Using first interface: 0x00 Using endpoints 0x01 (out) and 0x81 (in) Inquiring device details; driver will be detached ... Cant't do driver detection and detaching on this platform. SCSI inquiry data (for identification) ------------------------- Vendor String: HSPA Model String: USB SCSI CD-ROM Revision String: 2.31 ------------------------- USB description data (for identification) ------------------------- Manufacturer: ZTE,Incorporated Product: ZTE WCDMA Technologies MSM Serial No.: P673A3H3GD010000 ------------------------- Setting up communication with interface 0 Using endpoint 0x01 for message sending ... Trying to send message 1 to endpoint 0x01 ... OK, message successfully sent Reading the response to message 1 (CSW) ... OK, response successfully read (13 bytes). Trying to send message 2 to endpoint 0x01 ... OK, message successfully sent Reading the response to message 2 (CSW) ... Response reading got error -6 Device is gone, skipping any further commands -> Run lsusb to note any changes. Bye.
I then have two new PPP interfaces /dev/cuaU0.1 and /dev/cuaU0.2
Unfortunately, I have no simcard to test any further :(
-
Ah, looks promising. :)
You can try talking to the modem with cu or tip like I did. If it responds to AT commands I would expect it to work.Steve
-
The next thing to try is adding the below line to the firewall config to test whether pfSense will switch the modem before it does the PPP dial:
<shellcmd>usb_modeswitch -c /usr/local/etc/modem.txt</shellcmd>
-
If not then try <earlyshellcmd>instead.
Steve</earlyshellcmd>
-
It does respond to AT commands on cuaU0.2 :)
My question is, what is cuaU0.1 which is also available to assign under PPP
Also, when I assign the PPP to an interface, I also see cuaU0.0 and cuau0 in the 'Modem Port' dropdown list so i'm a little confused ???
-
Probably due to the way pfSense finds the serial ports to display:
$serialports = pfSense_get_modem_devices();
I can't find that function but if it relies on, for example, sysctl dev.u3g then they won't appear there.
The reason that the modem provides several serial ports is not obvious to me but it seems it's possible to get stats from the modem on one interface whilst connected via another, signal strength, baud rate etc.
Steve
-
Thanks Steve.
I found a simcard, there's no credit on it but it still connects and gets an IP address.
I've tried both the shellcmd and earlyshellcmd options but sometimes there is a delay until the actual switch occurs. The boot sequence continues regardless, the PPP interface is brought up but the modem is not yet ready so a WAN connection isn't established. If I go into the GUI and manually hit connect, PPP is dialled and the WAN comes online.
Any idea of how we can delay bringing up PPP until we know the modem has successfully switched?
-
What happens when it tries to dial out before the interface is switched?
I'm surprised that it doesn't just keep trying.
Maybe using dial-on demand or idle time out.You could write a script that ran usb_modeswitch, waited and then called the appropriate interface connect function.
Steve