Need som help configurating Pfsense. Bridge mode? VPI? VCI?
-
"providerline–------DSL-modem-------WAN/pfsense/lan-----your network"
Its like that.
But Bluecom told me that VPI and VCI shoud be configurated in the router, and I don't think the modem has a firmware, no way of entring it. The modem has not worked (as I know) on any other routers. I Have this 3com router, but I cant find VPI and VCI there either so I desided to rather make Pfsense work instead. Bluecom has no entring password or username. If I plug the cable from the modem and right into the computer, I have internett without any configurating or software installing.
Do every DSL-providers have and IP adress? And what is actually DHCP? I thought that was a server that proveded the network with its own IP-adresses (for example 192-168.1.xxx)?
-
VPI/VCI is a function of you're modem, not pfSense.
-
No IP = no internet. Yes, every provider has IPs.
And the way you describe it it should just work in factory default settings of the pfsense as it has DHCP on wan by default. Try to powercycle the modem. Some providers have issues with assigning IPs when the MAC address of the networkcard they see has changed. -
I see… But what about bridging mode? Is that a deafult function? And what is Powercycle?
Last thing about these VPI and VCI. Do this have to be correct to have internett at all? Cuz I have interett if a plug the cable from the modem to my computer, do this mean that VPI and VCI are correct?
What about DNS adresses? Leave these open or set the adress that I got from Bluecom? Shoud I do anything with the MAC adress? If Im remembering correctly, PFsense had an opening for writing down and MAC adress somwhere :P
-
If it works with your computer directly connected you don't have a VCP VPI issues. Powercycle means unplug power and replug it. switch off and on. Leave it unpowered for some time (1 minute or so). If your provider has given you DNS adresses enter them at system>general and leave the option "allow DNS ser list to be overridden…" checked.
-
Thanks for all the help! Pfsense is "configurated" and the internet is up and running :D
-
Thanks for all the help! The internet is now up and running :D
But I have a question. Where can I block/unblock programs such as p2p programs, msn messenger etc? Cuz it seems like MSN messenger is blocket :S The internet is working fine, but not msn :(
-
msn messinger shoud work
it uses port 80 just like the websites
only for cam and sound it needs poorts from the wan site to be opend to the ipadress on the lan site
you use port forwarding on the nat tab for that
same with p2p u need poorts from the wan site of pfsense to be opend to youre pc
olso you need to be opening those poorts on you windows pc firewallyou can only open those poorts to 1 pc on youre network
so 2 pc's with edonkey on the same poorts is not goining to work -
msn messinger shoud work
it uses port 80 just like the websites
only for cam and sound it needs poorts from the wan site to be opend to the ipadress on the lan site
you use port forwarding on the nat tab for that
same with p2p u need poorts from the wan site of pfsense to be opend to youre pc
olso you need to be opening those poorts on you windows pc firewallyou can only open those poorts to 1 pc on youre network
so 2 pc's with edonkey on the same poorts is not goining to workExactly, you now have a firewall that blocks unwanted connections from the outside (looks like you had no firewall before from what I can read from the above discussion). You have to tell it that this is a connection you want to pass.
-
To enable voice and video communications with Windows Messenger through a non-UPnP firewall, configure the firewall to allow incoming traffic on UDP ports 5004 – 65535.
For other purposes, enable the following ports:
•File Transfer: tcp 6891 (to allow 10 simultaneous file transfers open ports 6891 through 6900)
•Application and Whiteboard Sharing: tcp 1503
•Remote Assistance: tcp 3389