Enter full pathname of shell or RETURN for /bin/sh:

Stef

Hi

I'm trying to install a new wrap box soekris net4801 with netbios 1.30

I've tried multiple cf cards so far, 512 Mb & 1 Gb

I've tried the embedded image as well as creating an image from a live cd,

The problem happens with 1.01 as well as with 1.2 beta 1

What's going wrong ?

Soekris settings:
ConSpeed = 9600
ConLock = Enabled
ConMute = Disabled
BIOSentry = Enabled
PCIROMS = Enabled
PXEBoot = Enabled
FLASH = Primary
BootDelay = 5
FastBoot = Disabled
BootPartition = Disabled
BootDrive = 80 81 F0 FF
ShowPCI = Enabled
Reset = Hard

Boot information:

net4801

0256 Mbyte Memory CPU Geode 266 Mhz

Pri Mas SanDisk SDCFB-512 LBA 993-16-63 500 Mbyte

Slot Vend Dev ClassRev Cmd Stat CL LT HT Base1 Base2 Int
–-----------------------------------------------------------------
0:00:0 1078 0001 06000000 0107 0280 00 00 00 00000000 00000000
0:06:0 100B 0020 02000000 0107 0290 00 3F 00 0000E101 A0000000 10
0:07:0 100B 0020 02000000 0107 0290 00 3F 00 0000E201 A0001000 10
0:08:0 100B 0020 02000000 0107 0290 00 3F 00 0000E301 A0002000 10
0:18:2 100B 0502 01018001 0005 0280 00 00 00 00000000 00000000
0:19:0 0E11 A0F8 0C031008 0117 0280 08 38 00 A0003000 00000000 11

1 Seconds to automatic boot. Press Ctrl-P for entering Monitor.
/boot/kernel/kernel text=0x4a4338 data=0x8fe74+0x41138 |
|
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]…
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.1-RELEASE-p10 #0: Sun Oct 29 01:44:26 UTC 2006
sullrich@builder.livebsd.com:/usr/obj.pfSense/usr/src/sys/pfSense_wrap.6
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Geode(TM) Integrated Processor by National Semi (266.66-MHz 586-class CPU)
Origin = "Geode by NSC" Id = 0x540 Stepping = 0
Features=0x808131 <fpu,tsc,msr,cx8,cmov,mmx>real memory = 268435456 (256 MB)
avail memory = 253317120 (241 MB)
wlan: mac acl policy registered
ath_hal: 0.9.16.16 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
cpu0 on motherboard
pcib0: <host to="" pci="" bridge="">pcibus 0 on motherboard
pci0: <pci bus="">on pcib0
sis0: <natsemi 10="" dp8381[56]="" 100basetx="">port 0xe100-0xe1ff mem 0xa0000000-0xa000
0fff irq 10 at device 6.0 on pci0
sis0: Silicon Revision: DP83816A
miibus0: <mii bus="">on sis0
ukphy0: <generic ieee="" 802.3u="" media="" interface="">on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: Ethernet address: 00:00:24:c7:a7:24
sis1: <natsemi 10="" dp8381[56]="" 100basetx="">port 0xe200-0xe2ff mem 0xa0001000-0xa000
1fff irq 10 at device 7.0 on pci0
sis1: Silicon Revision: DP83816A
miibus1: <mii bus="">on sis1
ukphy1: <generic ieee="" 802.3u="" media="" interface="">on miibus1
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis1: Ethernet address: 00:00:24:c7:a7:25
sis2: <natsemi 10="" dp8381[56]="" 100basetx="">port 0xe300-0xe3ff mem 0xa0002000-0xa000
2fff irq 10 at device 8.0 on pci0
sis2: Silicon Revision: DP83816A
miibus2: <mii bus="">on sis2
ukphy2: <generic ieee="" 802.3u="" media="" interface="">on miibus2
ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis2: Ethernet address: 00:00:24:c7:a7:26
Geode GPIO@ = 6100
Geode Soekris net4801 comBIOS ver. 1.30 20070326 Copyright (C) 2000-2007
isab0: <pci-isa bridge="">port 0x6100-0x613f,0x6200-0x623f at device 18.0 on pci0
isa0: <isa bus="">on isab0
pci0: <bridge>at device 18.1 (no driver attached)
atapci0: <national geode="" sc1100="" ata33="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0
x177,0x376,0xe000-0xe00f at device 18.2 on pci0
ata0: <ata 0="" channel="">on atapci0
ata1: <ata 1="" channel="">on atapci0
Geode CBA@ 0x6000
Geode rev: 06 03
Timecounter "Geode" frequency 27000000 Hz quality 1000
pci0: <bridge>at device 18.5 (no driver attached)
ohci0: <ohci (generic)="" usb="" controller="">mem 0xa0003000-0xa0003fff irq 11 at devic
e 19.0 on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: <ohci (generic)="" usb="" controller="">on ohci0
usb0: USB revision 1.0
uhub0: (0x0e11) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
orm0: <isa option="" rom="">at iomem 0xc8000-0xd0fff on isa0
ppc0: parallel port not found.
sio0 at port 0x3f8-0x3ff irq 4 flags 0x30 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
Timecounters tick every 10.000 msec
Fast IPsec: Initialized Security Association Processing.
ad0: 488MB <sandisk sdcfb-512="" hdx="" 4.04="">at ata0-master PIO4
GEOM_LABEL: Label for provider ad0a is ufs/pfSense.
GEOM_LABEL: Label for provider ad0d is ufs/pfSenseCfg.
Trying to mount root from ufs:/dev/ufs/pfSense

___
/ f
/ p _/ Sense
__/
_Enter full pathname of shell or RETURN for /bin/sh:

Any help would be appreciated.

Thanks
Stef</sandisk></isa></ohci></ohci></bridge></ata></ata></national></bridge></isa></pci-isa></generic></mii></natsemi></generic></mii></natsemi></generic></mii></natsemi></pci></host></fpu,tsc,msr,cx8,cmov,mmx>