Problem with Intel pro 100b/+
-
When i want use this NICs and take out rl NIC all looks good. POST, BOOTIX, PF Booting, and…
PF don't see this INTELs. On Linux Debian all are working good (almost all - auto dhcp doesn't work ). Old Intel 82557 works fine.BTW:
Sorry for my english. -
You sure it's not seeing it? After changing NIC's, you'll have to re-assign interfaces.
-
Debian testing/sid:
e100: Intel(R) PRO/100 Network Driver, 3.5.17-k2-NAPI
e100: Copyright1999-2006 Intel Corporation
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
e100: eth0: e100_probe: addr 0xdf100000, irq 10, MAC addr 00:03:47:AD:0A:D2
….
e100: eth1: e100_watchdog: link up, 100Mbps, full-duplexpfSense (Intel 82557, Realtek, Intel 82559[pro 100b/+]):
$ dmesg
Copyright1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE-p5 #0: Sat Jun 2 12:29:20 EDT 2007
sullrich@builder6.pfsense.com:/usr/obj.pfSense/usr/src/sys/pfSense.6
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel Celeron (634.78-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x686 Stepping = 6
Features=0x383fbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,mmx,fxsr,sse>real memory = 133111808 (126 MB)
avail memory = 120455168 (114 MB)
wlan: mac acl policy registered
kbd1 at kbdmux0
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <ibm cdtpwspt="">on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0xf808-0xf80b on acpi0
cpu0: <acpi cpu="">on acpi0
acpi_throttle0: <acpi cpu="" throttling="">on cpu0
pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0
pci0: <acpi pci="" bus="">on pcib0
agp0: <intel 82810e="" (i810e="" gmch)="" svga="" controller="">mem 0xf8000000-0xfbffffff,0xfe880000-0xfe8fffff irq 11 at device 1.0 on pci0
pcib1: <acpi pci-pci="" bridge="">at device 30.0 on pci0
pci1: <acpi pci="" bus="">on pcib1
fxp0: <intel 100="" 82557="" pro="" ethernet="">port 0x74a0-0x74bf mem 0xfe7ff000-0xfe7fffff,0xfea00000-0xfeafffff irq 15 at device 4.0 on pci1
miibus0: <mii bus="">on fxp0
nsphy0: <dp83840 10="" 100="" media="" interface="">on miibus0
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: Ethernet address: 00:20:35:67:0d:31
rl0: <realtek 10="" 8139="" 100basetx="">port 0x7800-0x78ff mem 0xfe9fef00-0xfe9fefff irq 10 at device 5.0 on pci1
miibus1: <mii bus="">on rl0
rlphy0: <realtek internal="" media="" interface="">on miibus1
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:0d:f3:05:08:d7
isab0: <pci-isa bridge="">at device 31.0 on pci0
isa0: <isa bus="">on isab0
atapci0: <intel ich="" udma66="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376 at device 31.1 on pci0
ata0: <ata 0="" channel="">on atapci0
ata1: <ata 1="" channel="">on atapci0
pci0: <serial bus,="" smbus="">at device 31.3 (no driver attached)
acpi_button0: <power button="">on acpi0
fdc0: <floppy drive="" controller="">port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <ecp parallel="" printer="" port="">port 0x378-0x37f,0x778-0x77f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
ppbus0: <parallel port="" bus="">on ppc0
lpt0: <printer>on ppbus0
lpt0: Interrupt-driven port
ppi0: <parallel i="" o="">on ppbus0
atkbdc0: <keyboard controller="" (i8042)="">port 0x60,0x64 irq 1 on acpi0
atkbd0: <at keyboard="">irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
speaker0: <pc speaker="">port 0x61 on acpi0
pmtimer0 on isa0
orm0: <isa option="" roms="">at iomem 0xc0000-0xc7fff,0xc8000-0xcdfff on isa0
sc0: <system console="">at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <generic isa="" vga="">at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 634775898 Hz quality 800
Timecounters tick every 1.000 msec
Fast IPsec: Initialized Security Association Processing.
ad0: 1007MB <wdc ac11000h="" 12.07h12="">at ata0-master WDMA2
acd0: CDROM <crd-8400b 1.12="">at ata0-slave PIO4
Trying to mount root from ufs:/dev/ad0s1a
fxp0: link state changed to UP
rl0: link state changed to UP
fxp0: link state changed to DOWN
rl0: link state changed to DOWN
fxp0: link state changed to UP
rl0: link state changed to UP
pflog0: promiscuous mode enabled</crd-8400b></wdc></generic></system></isa></pc></at></keyboard></parallel></printer></parallel></ecp></floppy></power></serial></ata></ata></intel></isa></pci-isa></realtek></mii></realtek></dp83840></mii></intel></acpi></acpi></intel></acpi></acpi></acpi></acpi></ibm></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,mmx,fxsr,sse>