Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    Watchguard Firebox XTM 8 Series

    Hardware
    23
    234
    113.4k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • M
      meph
      last edited by

      @DeLorean:

      @meph:

      Anybody have a backup of the watchguard OS available? I bought this watchguard off ebay and it had pfsense installed… i would like to restore it. any help would be appreciated.

      You have got PM  :)

      Grtz
      DeLorean

      Thanks… let me give it a try.

      1 Reply Last reply Reply Quote 0
      • D
        DeLorean
        last edited by

        Did it work ?

        Grtz
        DeLorean

        1 Reply Last reply Reply Quote 0
        • B
          BrettMerrick
          last edited by

          Hi,

          Found this thread extremely helpful, thanks to all who have contributed!

          I was able to install 2.4.1 on to the 1GB CF card by using the VGA hack and putting the installer image on a sata drive. I did have to plug the CF in shortly after boot though so it booted from the sata drive first…

          I also had to manually partition the drive as it complained that it wasn't a full 1GB.

          I found than once installed I could enable the serial console by modifying /boot/device.hints and switching the IRQ and Address for the uart:

          hint.uart.0.at="isa"
          hint.uart.0.port="0x2F8"
          hint.uart.0.flags="0x10"
          hint.uart.0.irq="3"
          hint.uart.1.at="isa"
          hint.uart.1.port="0x3F8"
          hint.uart.1.irq="4"

          I got the LCD working by simply installing the LCDproc package and configuring it for Parallel port 1 and Watchguard Firebox with SDEC. I made a few other setting changes to my preference, including setting the backlight to on, however it seems to switch off again after a short time.

          Now I just need to sort the noise! - Anything I can help with mppkll?

          1 Reply Last reply Reply Quote 0
          • D
            DaveinTN
            last edited by

            Any updates to the program to control the fans and LCD on the XTM 8 Series?

            1 Reply Last reply Reply Quote 0
            • D
              DaveinTN
              last edited by

              I'm looking at selling this XTM 850 on eBay and need to know if there's a way to return the internal hard drive back to factory defaults?

              I have the SD card back to factory and it boots to the OS, however during testing of pFsense I used the drive. Is there a way to return for use with the embedded OS before I sell it?

              Thanks,

              1 Reply Last reply Reply Quote 0
              • S
                Scorch95
                last edited by

                If I’m not mistaken, which I often am, I do not believe these shipped with internal drives other than the CF.

                1 Reply Last reply Reply Quote 0
                • D
                  DaveinTN
                  last edited by

                  Mine had the 2GB CF card installed and a 250GB SATA hard drive mounted in a factory mount and connected.

                  1 Reply Last reply Reply Quote 0
                  • S
                    Scorch95
                    last edited by

                    I stand corrected. Do you have a picture of the mount?

                    1 Reply Last reply Reply Quote 0
                    • stephenw10S
                      stephenw10 Netgate Administrator
                      last edited by

                      @daveinfla:

                      Mine had the 2GB CF card installed and a 250GB SATA hard drive mounted in a factory mount and connected.

                      Ooo. Fancy.  ;)

                      Probably for use as a cache. I'm not aware of any models based on the XTM8 like the old SSL models were. They came with a HD instead of CF.

                      Steve

                      1 Reply Last reply Reply Quote 0
                      • stephenw10S
                        stephenw10 Netgate Administrator
                        last edited by 

                        2.3.5-RELEASE][admin@xtm8.stevew.lan]/root: ./WGXepc64 
Found Firebox XTM8
WGXepc Version 1.3 5/3/2018 stephenw10
WGXepc can accept two arguments:
 -f (CPU fan) will return the current and minimum fan speed or if followed
    by a number in hex, 00-FF, will set it.
 -f2 (System fan) will return the current and minimum fan speed or if followed
    by a number in hex, 00-FF, will set it.
 -l (led) will set the arm/disarm led state to the second argument:
    red, green, red_flash, green_flash, red_flash_fast, green_flash_fast, off
 -b (backlight) will set the lcd backlight to the second argument:
    on or off. Do not use with LCD driver.
 -t (temperature) shows the current CPU temperature reported by the
    SuperIO chip. X-e box only.
Not all functions are supported by all models
[2.3.5-RELEASE][admin@xtm8.stevew.lan]/root: ./WGXepc64 -f
Found Firebox XTM8
Current CPU fanspeed is ???, minimum is 3f
[2.3.5-RELEASE][admin@xtm8.stevew.lan]/root: ./WGXepc64 -f 37
Found Firebox XTM8
IT87 Fanctl set to sane defaults
Minimum CPU fanspeed set to 37
[2.3.5-RELEASE][admin@xtm8.stevew.lan]/root: ./WGXepc64 -f2
Found Firebox XTM8
Current System fanspeed is ???, minimum is 38
[2.3.5-RELEASE][admin@xtm8.stevew.lan]/root: ./WGXepc64 -l green_flash_fast
Found Firebox XTM8
IT87 GPIO pins configured
[2.3.5-RELEASE][admin@xtm8.stevew.lan]/root: ./WGXepc64 -l green
Found Firebox XTM8

                        64bit binary. Source.

                        ;)

                        Steve

                        1 Reply Last reply Reply Quote 0
                        • P
                          pglover19
                          last edited by

                          @stephenw10:

                          2.3.5-RELEASE][admin@xtm8.stevew.lan]/root: ./WGXepc64 
Found Firebox XTM8
WGXepc Version 1.3 5/3/2018 stephenw10
WGXepc can accept two arguments:
 -f (CPU fan) will return the current and minimum fan speed or if followed
    by a number in hex, 00-FF, will set it.
 -f2 (System fan) will return the current and minimum fan speed or if followed
    by a number in hex, 00-FF, will set it.
 -l (led) will set the arm/disarm led state to the second argument:
    red, green, red_flash, green_flash, red_flash_fast, green_flash_fast, off
 -b (backlight) will set the lcd backlight to the second argument:
    on or off. Do not use with LCD driver.
 -t (temperature) shows the current CPU temperature reported by the
    SuperIO chip. X-e box only.
Not all functions are supported by all models
[2.3.5-RELEASE][admin@xtm8.stevew.lan]/root: ./WGXepc64 -f
Found Firebox XTM8
Current CPU fanspeed is ???, minimum is 3f
[2.3.5-RELEASE][admin@xtm8.stevew.lan]/root: ./WGXepc64 -f 37
Found Firebox XTM8
IT87 Fanctl set to sane defaults
Minimum CPU fanspeed set to 37
[2.3.5-RELEASE][admin@xtm8.stevew.lan]/root: ./WGXepc64 -f2
Found Firebox XTM8
Current System fanspeed is ???, minimum is 38
[2.3.5-RELEASE][admin@xtm8.stevew.lan]/root: ./WGXepc64 -l green_flash_fast
Found Firebox XTM8
IT87 GPIO pins configured
[2.3.5-RELEASE][admin@xtm8.stevew.lan]/root: ./WGXepc64 -l green
Found Firebox XTM8

                          64bit binary. Source.

                          ;)

                          Steve

                          Thank you..The program works on my WatchGuard XTM 810 appliance.

                          O 1 Reply Last reply Reply Quote 0
                          • stephenw10S
                            stephenw10 Netgate Administrator
                            last edited by

                            Glad to hear it. 😉

                            I recommend you do some sort of load test to make sure the fans are spinning up correctly and the peak temp values aren't too high.
                            The default settings are just way off so I made what I think are reasonable choices for the standard CPU.

                            Fan PWM values should be between 00 and 7f, 127 levels, but in reality 32 is stopped and 50 appears to be the maximum. I set both cpu and system fan minimum values to 38 but you can override that by setting a number.

                            The CPU fan should start to ramp up at 40C and the system fan at 35C. Both ramp up by one 'fan setting' per degree so should quite quickly start making noise with a load.

                            Steve

                            1 Reply Last reply Reply Quote 0
                            • O
                              ojguerrier
                              last edited by

                              @pglover19

                              Could you help me please , i have the same model.

                              Thanks you

                              1 Reply Last reply Reply Quote 0
                              • O
                                ojguerrier @pglover19
                                last edited by

                                @pglover19

                                I have the same model ( XTM 810) , could you help me please ?

                                Thanks

                                1 Reply Last reply Reply Quote 0
                                • stephenw10S
                                  stephenw10 Netgate Administrator
                                  last edited by

                                  Help you do what?

                                  What are you doing? What do you expect to happen? What's actually happening?

                                  Steve

                                  1 Reply Last reply Reply Quote 0
                                  • O
                                    ojguerrier
                                    last edited by

                                    Hello

                                    I have a XTM 8 series, I would like install PFSense on it. Can you help me please.

                                    Best regards

                                    1 Reply Last reply Reply Quote 0
                                    • stephenw10S
                                      stephenw10 Netgate Administrator
                                      last edited by

                                      Are you installing to a CF card or a SATA device? Do you have some means of writing to the CF or installing to the SATA device outside on the XTM8?

                                      Steve

                                      O 1 Reply Last reply Reply Quote 0
                                      • O
                                        ojguerrier @stephenw10
                                        last edited by

                                        @stephenw10

                                        I have a CF 1Gb and an HDD 500Gb. What ISO PFsense to copy on the CF 1Gb ? And how to install PFsense on the HDD.

                                        Thanks

                                        1 Reply Last reply Reply Quote 0
                                        • stephenw10S
                                          stephenw10 Netgate Administrator
                                          last edited by

                                          Noting here for reference since it somehow seems to have been missed and I found myself having to search for it again.

                                          The only change required to enable the serial console on com2 is this loader line:

                                          comconsole_port="0x2F8"

                                          Add that to /boot/loader.conf.local and/or set it at the loader prompt initially.

                                          Steve

                                          D 1 Reply Last reply Reply Quote 0
                                          • D
                                            DeLorean @stephenw10
                                            last edited by

                                            @stephenw10 said in Watchguard Firebox XTM 8 Series:

                                            Noting here for reference since it somehow seems to have been missed and I found myself having to search for it again.

                                            The only change required to enable the serial console on com2 is this loader line:

                                            comconsole_port="0x2F8"

                                            Add that to /boot/loader.conf.local and/or set it at the loader prompt initially.

                                            Steve

                                            Hi,

                                            This is my first XTM810 that i'm converting to a pfsense box, but damn, who weird is this box compared to a XTM5 series ?
                                            The em0 to em9 assigning is crisscross, these boxes can't shutdown because of the AT powersupply design with a hard on/off switch like the ancient X-Core boxes.
                                            At the moment i use a 1Gb CF card with a older version (2.4.4) 64bit full version with Ramdisk enabled from a XTM5 box, i can login with the Web GUI, and with the above fix of Stephen for activating the COM2 port, i can also see whats happening throug serial console with PuTTy.
                                            But the 2 major problems are :
                                            No internet is passing the box, while on the dashboard the gateway is showing green, and the WAN (em0) has a dynamic IP.
                                            The second problem is the Bios of this XTM810 (labeled FW-8750 WG v1.1 on the motherboard and Bios version 1.2 labeled on the LCD) is that i can only make a backup of the Bios with a GQ-4X Willem Programmer through the SPI interface, and that the Bios file is 2Mb in size. Flashrom gives a read error when trying to backup the original Bios.
                                            Erasing the Bios and flashing this backup back with Flashrom gives also a read error, and the 1Mb Bios files brick this box each time.
                                            Also, only the 1Mb Bios files can be opened by the Amibcp tool, i have tried 6 or 7 different versions of Amibcp from version v3.13 to v4.53, the 1Mb Bios files can be opened, but the 2Mb Bios file that i previously backup can't be opened for editing. So first i though that this backup was corrupt, after bricking the box with the 1Mb unlocked Bios, i revived the box again with the 2Mb Bios that i backup, so it's definitely not corrupt this 2Mb Bios file.
                                            With the original Watchguard firmware 12.1.3 (latest version), internet works fine , so the hardware of this box is okay.
                                            I have also tried with and without the AGP disabling fix, because on Supermicro motherboards this fix works great when the assigning of the extra added interfaces doesn't work properly.
                                            So any help or tips to get pfSense working will be great.

                                            Grtz
                                            DeLorean

                                            mr.roshM 1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post