Pfsense with 3 NICS

bryan.paradis

i am using all my 3 NICS to use Teaming so all traffic will go thought the WAN.

Guess it could be a lot of things. Jamerson you need to really clarify and perhaps draw a diagram of what you want.

johnpoz

Well clearly his NOT doing that, since he has a nic in his lan network and nic in his wan network - so how could he be "teaming" them. He clearly doesn't understand the term.

For that matter he doesn't even have 3 nics, be it physical or VM.. Look at his esxi host networking he posted

He doesn't even have a lan2 interface listed in his VM networking for pfsense, which I take is the firewall vm.. Yet he says he created firewall rules in pfsense for lan? So what did he connect to lan2? Mystery to be sure.

Jamerson

sorry guys for my late reply ( been sick ).
about the NIC teaming haven't configured it yet on the LAB and I know what is NIC teaming by the way, that why you don't see it on the Diagram.
what I need is when VM on the same LAN2 on ESXI that they need to reach the internet.
My PFSENSE has 3 NICS,
WAN and LAN1 and LAN2
LAN 1 and LAN 2 are not attached to Physical NIC,
attached is screenshot of the LAB
I didn't add the NIC yet of the PFSENSE to each group LAN 1 and LAN 2.
on LAN 1 will have PFSENSE NIC 2
on LAN 2 will have PFSENSE NIC 3
so when I move a VM to the LAN 1 0r LAN 2 it doesn't reach the internet. this is my problem.
when I attached a physical NIC to LAN 1 or LAN 2 on the ESXI it works

LAN1.jpg_thumb

johnpoz

Dude how is anything going to use pfsense if pfsense has no VIRTUAL nic in the switch??

How is any VM going to connect to pfsense lan1 or lan2 if there is NOTHING connected to the vswitch? Does not matter if the vswitch is not connected to the physical world or not..

See bottom of my virtual network from esxi

See how pfsense has a virtual interface connected into the vswitch, so that other virtual machines with a virtual interface connected to this vswitch can connect to pfsense and then access the real world (internet or lan or wlan) via the physical nics connected to those vswitches.

You have nothing connected to your lan1 or lan2 from your drawing - no pfsense interfaces, no vms – so NO how would anything use it.. What does pfsense show for its interfaces, since from your drawing you don't show any lan1 or lan2 interfaces for pfsense at all.

So for example


[2.1.1-PRERELEASE][admin@pfsense.local.lan]/root(1): ifconfig
em0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
        options=98 <vlan_mtu,vlan_hwtagging,vlan_hwcsum>ether 00:50:56:00:00:02
        inet 192.168.1.253 netmask 0xffffff00 broadcast 192.168.1.255
        inet6 fe80::250:56ff:fe00:2%em0 prefixlen 64 scopeid 0x1
        inet6 2001:470:1f11:9c4::1 prefixlen 64
        nd6 options=1 <performnud>media: Ethernet autoselect (1000baseT <full-duplex>)
        status: active
em1: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
        options=98 <vlan_mtu,vlan_hwtagging,vlan_hwcsum>ether 00:50:56:00:00:01
        inet 24.13.xx.xx netmask 0xfffff800 broadcast 255.255.255.255
        inet6 fe80::250:56ff:fe00:1%em1 prefixlen 64 scopeid 0x2
        nd6 options=1 <performnud>media: Ethernet autoselect (1000baseT <full-duplex>)
        status: active
em2: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
        options=98 <vlan_mtu,vlan_hwtagging,vlan_hwcsum>ether 00:0c:29:1e:18:90
        inet 192.168.2.253 netmask 0xffffff00 broadcast 192.168.2.255
        inet6 fe80::20c:29ff:fe1e:1890%em2 prefixlen 64 scopeid 0x3
        nd6 options=1 <performnud>media: Ethernet autoselect (1000baseT <full-duplex>)
        status: active
em3: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
        options=98 <vlan_mtu,vlan_hwtagging,vlan_hwcsum>ether 00:0c:29:1e:18:9a
        inet 192.168.3.253 netmask 0xffffff00 broadcast 192.168.3.255
        inet6 fe80::20c:29ff:fe1e:189a%em3 prefixlen 64 scopeid 0x4
        nd6 options=1 <performnud>media: Ethernet autoselect (1000baseT <full-duplex>)
        status: active</full-duplex></performnud></vlan_mtu,vlan_hwtagging,vlan_hwcsum></up,broadcast,running,simplex,multicast></full-duplex></performnud></vlan_mtu,vlan_hwtagging,vlan_hwcsum></up,broadcast,running,simplex,multicast></full-duplex></performnud></vlan_mtu,vlan_hwtagging,vlan_hwcsum></up,broadcast,running,simplex,multicast></full-duplex></performnud></vlan_mtu,vlan_hwtagging,vlan_hwcsum></up,broadcast,running,simplex,multicast>

Those are the interfaces in my virtual pfsense.. Se how pfsense has 4 interfaces. One in each segment (wan, lan, wlan, dmz) notice how in my esxi network pfsense is listed as having a connection in each vswitch that is connected to each one of pfsense interfaces. If I connect a virtual machine to that vswitch, via a virtual interface. Like the W7 machine on the bottom above pfsense on the dmz vswitch.. It can talk to pfsense over the vswitch on its dmz virtual interface and then pfsense can route it to any of its other interfaces over virtual - which may or may not have access into the physical world via a physical adapter connected to that vswitch.

pfsensemissing.png_thumb

pfsenseconnected.png_thumb

Jamerson

@johnpoz:

Dude how is anything going to use pfsense if pfsense has no VIRTUAL nic in the switch??

How is any VM going to connect to pfsense lan1 or lan2 if there is NOTHING connected to the vswitch? Does not matter if the vswitch is not connected to the physical world or not..

See bottom of my virtual network from esxi

See how pfsense has a virtual interface connected into the vswitch, so that other virtual machines with a virtual interface connected to this vswitch can connect to pfsense and then access the real world (internet or lan or wlan) via the physical nics connected to those vswitches.

You have nothing connected to your lan1 or lan2 from your drawing - no pfsense interfaces, no vms – so NO how would anything use it.. What does pfsense show for its interfaces, since from your drawing you don't show any lan1 or lan2 interfaces for pfsense at all.

So for example
[2.1.1-PRERELEASE][admin@pfsense.local.lan]/root(1): ifconfig
em0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
        options=98 <vlan_mtu,vlan_hwtagging,vlan_hwcsum>ether 00:50:56:00:00:02
        inet 192.168.1.253 netmask 0xffffff00 broadcast 192.168.1.255
        inet6 fe80::250:56ff:fe00:2%em0 prefixlen 64 scopeid 0x1
        inet6 2001:470:1f11:9c4::1 prefixlen 64
        nd6 options=1 <performnud>media: Ethernet autoselect (1000baseT <full-duplex>)
        status: active
em1: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
        options=98 <vlan_mtu,vlan_hwtagging,vlan_hwcsum>ether 00:50:56:00:00:01
        inet 24.13.xx.xx netmask 0xfffff800 broadcast 255.255.255.255
        inet6 fe80::250:56ff:fe00:1%em1 prefixlen 64 scopeid 0x2
        nd6 options=1 <performnud>media: Ethernet autoselect (1000baseT <full-duplex>)
        status: active
em2: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
        options=98 <vlan_mtu,vlan_hwtagging,vlan_hwcsum>ether 00:0c:29:1e:18:90
        inet 192.168.2.253 netmask 0xffffff00 broadcast 192.168.2.255
        inet6 fe80::20c:29ff:fe1e:1890%em2 prefixlen 64 scopeid 0x3
        nd6 options=1 <performnud>media: Ethernet autoselect (1000baseT <full-duplex>)
        status: active
em3: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
        options=98 <vlan_mtu,vlan_hwtagging,vlan_hwcsum>ether 00:0c:29:1e:18:9a
        inet 192.168.3.253 netmask 0xffffff00 broadcast 192.168.3.255
        inet6 fe80::20c:29ff:fe1e:189a%em3 prefixlen 64 scopeid 0x4
        nd6 options=1 <performnud>media: Ethernet autoselect (1000baseT <full-duplex>)
        status: active</full-duplex></performnud></vlan_mtu,vlan_hwtagging,vlan_hwcsum></up,broadcast,running,simplex,multicast></full-duplex></performnud></vlan_mtu,vlan_hwtagging,vlan_hwcsum></up,broadcast,running,simplex,multicast></full-duplex></performnud></vlan_mtu,vlan_hwtagging,vlan_hwcsum></up,broadcast,running,simplex,multicast></full-duplex></performnud></vlan_mtu,vlan_hwtagging,vlan_hwcsum></up,broadcast,running,simplex,multicast> 
Those are the interfaces in my virtual pfsense.. Se how pfsense has 4 interfaces. One in each segment (wan, lan, wlan, dmz) notice how in my esxi network pfsense is listed as having a connection in each vswitch that is connected to each one of pfsense interfaces. If I connect a virtual machine to that vswitch, via a virtual interface. Like the W7 machine on the bottom above pfsense on the dmz vswitch.. It can talk to pfsense over the vswitch on its dmz virtual interface and then pfsense can route it to any of its other interfaces over virtual - which may or may not have access into the physical world via a physical adapter connected to that vswitch.

hi John,
Let me thank you for your continue help really appreciate it.
apologies i've uploaded the wrong screenshot !
the attached is the correct screenshot

when a machine using LAN1 NIC as Gateway is not accessible the internet !

em0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
        options=9b <rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum>ether 00:50:56:a8:1a:4a
        inet 192.168.2.3 netmask 0xffffff00 broadcast 192.168.2.255
        inet6 fe80::250:56ff:fea8:1a4a%em0 prefixlen 64 scopeid 0x1
        nd6 options=1 <performnud>media: Ethernet autoselect (1000baseT <full-duplex>)
        status: active
em1: flags=8943 <up,broadcast,running,promisc,simplex,multicast>metric 0 mtu 1500
        options=9b <rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum>ether 00:50:56:8c:7e:c8
        inet 192.168.4.1 netmask 0xffffff00 broadcast 192.168.4.255
        inet6 fe80::250:56ff:fe8c:7ec8%em1 prefixlen 64 scopeid 0x2
        nd6 options=1 <performnud>media: Ethernet autoselect (1000baseT <full-duplex>)
        status: active
em2: flags=8943 <up,broadcast,running,promisc,simplex,multicast>metric 0 mtu 1500
        options=9b <rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum>ether 00:50:56:8c:a6:3b
        inet 192.168.6.0 netmask 0xffffff00 broadcast 192.168.6.255
        inet6 fe80::250:56ff:fe8c:a63b%em2 prefixlen 64 scopeid 0x3
        nd6 options=1 <performnud>media: Ethernet autoselect (1000baseT <full-duplex>)
        status: active
plip0: flags=8810 <pointopoint,simplex,multicast>metric 0 mtu 1500
pflog0: flags=100 <promisc>metric 0 mtu 33144
lo0: flags=8049 <up,loopback,running,multicast>metric 0 mtu 16384
        options=3 <rxcsum,txcsum>inet 127.0.0.1 netmask 0xff000000
        inet6 ::1 prefixlen 128
        inet6 fe80::1%lo0 prefixlen 64 scopeid 0x6
        nd6 options=3 <performnud,accept_rtadv>pfsync0: flags=0<> metric 0 mtu 1460
        syncpeer: 224.0.0.240 maxupd: 128 syncok: 1
enc0: flags=0<> metric 0 mtu 1536
bridge0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
        ether 02:1b:ed:00:ce:00
        id 00:00:00:00:00:00 priority 32768 hellotime 2 fwddelay 15
        maxage 20 holdcnt 6 proto rstp maxaddr 100 timeout 1200
        root id 00:00:00:00:00:00 priority 32768 ifcost 0 port 0
        member: em2 flags=143 <learning,discover,autoedge,autoptp>ifmaxaddr 0 port 3 priority 128 path cost 20000
        member: em1 flags=143 <learning,discover,autoedge,autoptp>ifmaxaddr 0 port 2 priority 128 path cost 20000
ovpns1: flags=8051 <up,pointopoint,running,multicast>metric 0 mtu 1500
        options=80000 <linkstate>inet6 fe80::250:56ff:fea8:1a4a%ovpns1 prefixlen 64 scopeid 0xa
        inet 192.168.200.1 --> 192.168.200.2 netmask 0xffffffff
        nd6 options=3 <performnud,accept_rtadv>Opened by PID 10306</performnud,accept_rtadv></linkstate></up,pointopoint,running,multicast></learning,discover,autoedge,autoptp></learning,discover,autoedge,autoptp></up,broadcast,running,simplex,multicast></performnud,accept_rtadv></rxcsum,txcsum></up,loopback,running,multicast></promisc></pointopoint,simplex,multicast></full-duplex></performnud></rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum></up,broadcast,running,promisc,simplex,multicast></full-duplex></performnud></rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum></up,broadcast,running,promisc,simplex,multicast></full-duplex></performnud></rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum></up,broadcast,running,simplex,multicast>

LAN1.jpg_thumb

johnpoz

Well for one this address is wrong

inet 192.168.6.0 that you have on em2

That is a network (wire address) with that mask netmask 0xffffff00 (/24 or 255.255.255.0) not a host or interface address. I would think it should be 192.168.6.1 - so fix that for starters.

Now on lan2, connect some Vms. Did you post the wrong drawing again - there are no other vms connected to vswitch2 or lan 2 in your drawing - so how is anything expected to connect to pfsense lan2 interface. Same with lan1 - there are NO other vms there either. Did you not understand my last post?

Once you have a vm actually connected to lan2 vswitch, and give pfsense an actual valid host IP that you want to use for the network you put it on.. Can the clients connected to that vswitch on the same network as pfsense interface ping it? What are the firewall rules for that interface. While the first lan you create when pfsense is installed will have a any any rule on it and allow outbound traffic to anywhere. When you add additional interfaces there will be NO rules, and you have to allow the traffic you want out on this new network segment. So what are you rules on lan2?

stephenw10

You have bridge0 containing both em1 and em2. They both have static IP addresses in different subnets. Are they both running dhcp? (Is that possible?). You have bridged the two subnets so that they both exist across both network segments. I'm fairly sure you don't want to do that.

Steve

doktornotor

I cannot see any pfSense anywhere on the networking diagrams you posted. Really dunno what you are trying to do there. When nothing's connected, nothing will work. Other than that - flush the mess you have created down the drain, and produce a barebones basic setup with 3 NICs. No "teaming", "bridging" and similar nonsense.

johnpoz

Good catch.. Didn't even get that far in his listing

bridge0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
ether 02:1b:ed:00:ce:00
id 00:00:00:00:00:00 priority 32768 hellotime 2 fwddelay 15
maxage 20 holdcnt 6 proto rstp maxaddr 100 timeout 1200
root id 00:00:00:00:00:00 priority 32768 ifcost 0 port 0
member: em2 flags=143 <learning,discover,autoedge,autoptp>ifmaxaddr 0 port 3 priority 128 path cost 20000
member: em1 flags=143 <learning,discover,autoedge,autoptp>ifmaxaddr 0 port 2 priority 128 path cost 20000

I just don't get it.. You really just click click and pfsense works out of the box – its like these users go out of their way to have issues.. Why would he have created a bridge?? When clearly he mentions multiple segments. And he seems to have a hard time posting actual info that is what his network is.. How do you not notice that what you posts shows NOTHING connected to your vswitches? ;)</learning,discover,autoedge,autoptp></learning,discover,autoedge,autoptp></up,broadcast,running,simplex,multicast>

Jamerson

@stephenw10:

You have bridge0 containing both em1 and em2. They both have static IP addresses in different subnets. Are they both running dhcp? (Is that possible?). You have bridged the two subnets so that they both exist across both network segments. I'm fairly sure you don't want to do that.

Steve

Hi Stephen
LAN2 has a DHCP enable and the machines recieves the IP from the DHCP server
192.168.6.11
255.255.255.0
192.168.6.1

@doktornotor:

I cannot see any pfSense anywhere on the networking diagrams you posted. Really dunno what you are trying to do there. When nothing's connected, nothing will work. Other than that - flush the mess you have created down the drain, and produce a barebones basic setup with 3 NICs. No "teaming", "bridging" and similar nonsense.

ASA Firewall is the PFSENSE on the diagrame,
i havent created any Teaming yet. i am just trying to get the VM to access the internet without Physical NIC attached to the Vswitch on the ESXI
@johnpoz:

Good catch.. Didn't even get that far in his listing

bridge0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
ether 02:1b:ed:00:ce:00
id 00:00:00:00:00:00 priority 32768 hellotime 2 fwddelay 15
maxage 20 holdcnt 6 proto rstp maxaddr 100 timeout 1200
root id 00:00:00:00:00:00 priority 32768 ifcost 0 port 0
member: em2 flags=143 <learning,discover,autoedge,autoptp>ifmaxaddr 0 port 3 priority 128 path cost 20000
member: em1 flags=143 <learning,discover,autoedge,autoptp>ifmaxaddr 0 port 2 priority 128 path cost 20000

I just don't get it.. You really just click click and pfsense works out of the box – its like these users go out of their way to have issues.. Why would he have created a bridge?? When clearly he mentions multiple segments. And he seems to have a hard time posting actual info that is what his network is.. How do you not notice that what you posts shows NOTHING connected to your vswitches? ;)</learning,discover,autoedge,autoptp></learning,discover,autoedge,autoptp></up,broadcast,running,simplex,multicast>

i have created a vm and attached to LAN2 with LAN2 NIC of PFSENSE
and still can't get to the internet
i didnt really created any bridg connection, probably it out of the box ?

Win7.jpg_thumb

route-print.jpg_thumb

doktornotor

@Jamerson:

i didnt really created any bridg connection, probably it out of the box ?

No, there is absolutely NO bridge created out of the box. As already suggested quite some time ago, reset the config to factory defaults and start from scratch, with a simple setup, and do not do anything else until you understand the consequences.

stephenw10

@Jamerson:

i didnt really created any bridg connection, probably it out of the box ?

Not any time I've installed pfSense. ;) Though I've never used the OVA preconfigured VM.
I too would not expect to see a bridge interface unless you have deliberately created one.

Steve

johnpoz

There is NO bridge out of the box that is for SURE!! You must of created it - delete that!!

And your saying your clients are getting this via dhcp

192.168.6.11
255.255.255.0
192.168.6.1

Well so 6.1 is your gateway? But pfsense doesn't have an IP on 6.1 via your ifconfig – it has .0 as its address.. Which is the WIRE and not a valid host IP for your mask of /24

em2: flags=8943 <up,broadcast,running,promisc,simplex,multicast>metric 0 mtu 1500
options=9b <rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum>ether 00:50:56:8c:a6:3b
inet 192.168.6.0 netmask 0xffffff00 broadcast 192.168.6.255
inet6 fe80::250:56ff:fe8c:a63b%em2 prefixlen 64 scopeid 0x3
nd6 options=1 <performnud>media: Ethernet autoselect (1000baseT <full-duplex>)
status: active</full-duplex></performnud></rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum></up,broadcast,running,promisc,simplex,multicast>

Jamerson

@johnpoz:

There is NO bridge out of the box that is for SURE!! You must of created it - delete that!!

And your saying your clients are getting this via dhcp

192.168.6.11
255.255.255.0
192.168.6.1

Well so 6.1 is your gateway? But pfsense doesn't have an IP on 6.1 via your ifconfig – it has .0 as its address.. Which is the WIRE and not a valid host IP for your mask of /24

em2: flags=8943 <up,broadcast,running,promisc,simplex,multicast>metric 0 mtu 1500
options=9b <rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum>ether 00:50:56:8c:a6:3b
inet 192.168.6.0 netmask 0xffffff00 broadcast 192.168.6.255
inet6 fe80::250:56ff:fe8c:a63b%em2 prefixlen 64 scopeid 0x3
nd6 options=1 <performnud>media: Ethernet autoselect (1000baseT <full-duplex>)
status: active</full-duplex></performnud></rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum></up,broadcast,running,promisc,simplex,multicast>

the 192.168.6.0 i fixed it,
the LAN 2 NIC was assigned with the wrong IP 192.168.6.0 but now it's 192.168.6.1
can you direct me how to create the bridg between the two LAN ?

em0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
        options=9b <rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum>ether 00:50:56:a8:1a:4a
        inet 192.168.2.3 netmask 0xffffff00 broadcast 192.168.2.255
        inet6 fe80::250:56ff:fea8:1a4a%em0 prefixlen 64 scopeid 0x1
        nd6 options=1 <performnud>media: Ethernet autoselect (1000baseT <full-duplex>)
        status: active
em1: flags=8943 <up,broadcast,running,promisc,simplex,multicast>metric 0 mtu 1500
        options=9b <rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum>ether 00:50:56:8c:7e:c8
        inet 192.168.4.1 netmask 0xffffff00 broadcast 192.168.4.255
        inet6 fe80::250:56ff:fe8c:7ec8%em1 prefixlen 64 scopeid 0x2
        nd6 options=1 <performnud>media: Ethernet autoselect (1000baseT <full-duplex>)
        status: active
em2: flags=8943 <up,broadcast,running,promisc,simplex,multicast>metric 0 mtu 1500
        options=98 <vlan_mtu,vlan_hwtagging,vlan_hwcsum>ether 00:50:56:8c:a6:3b
        inet6 fe80::250:56ff:fe8c:a63b%em2 prefixlen 64 scopeid 0x3
        inet 192.168.6.1 netmask 0xffffff00 broadcast 192.168.6.255
        nd6 options=1 <performnud>media: Ethernet autoselect (1000baseT <full-duplex>)
        status: active
plip0: flags=8810 <pointopoint,simplex,multicast>metric 0 mtu 1500
pflog0: flags=100 <promisc>metric 0 mtu 33144
lo0: flags=8049 <up,loopback,running,multicast>metric 0 mtu 16384
        options=3 <rxcsum,txcsum>inet 127.0.0.1 netmask 0xff000000
        inet6 ::1 prefixlen 128
        inet6 fe80::1%lo0 prefixlen 64 scopeid 0x6
        nd6 options=3 <performnud,accept_rtadv>pfsync0: flags=0<> metric 0 mtu 1460
        syncpeer: 224.0.0.240 maxupd: 128 syncok: 1
enc0: flags=0<> metric 0 mtu 1536
bridge0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
        ether 02:1b:ed:00:ce:00
        id 00:00:00:00:00:00 priority 32768 hellotime 2 fwddelay 15
        maxage 20 holdcnt 6 proto rstp maxaddr 100 timeout 1200
        root id 00:00:00:00:00:00 priority 32768 ifcost 0 port 0
        member: em2 flags=143 <learning,discover,autoedge,autoptp>ifmaxaddr 0 port 3 priority 128 path cost 20000
        member: em1 flags=143 <learning,discover,autoedge,autoptp>ifmaxaddr 0 port 2 priority 128 path cost 20000
ovpns1: flags=8051 <up,pointopoint,running,multicast>metric 0 mtu 1500
        options=80000 <linkstate>inet6 fe80::250:56ff:fea8:1a4a%ovpns1 prefixlen 64 scopeid 0xa
        inet 192.168.200.1 --> 192.168.200.2 netmask 0xffffffff
        nd6 options=3 <performnud,accept_rtadv>Opened by PID 10306</performnud,accept_rtadv></linkstate></up,pointopoint,running,multicast></learning,discover,autoedge,autoptp></learning,discover,autoedge,autoptp></up,broadcast,running,simplex,multicast></performnud,accept_rtadv></rxcsum,txcsum></up,loopback,running,multicast></promisc></pointopoint,simplex,multicast></full-duplex></performnud></vlan_mtu,vlan_hwtagging,vlan_hwcsum></up,broadcast,running,promisc,simplex,multicast></full-duplex></performnud></rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum></up,broadcast,running,promisc,simplex,multicast></full-duplex></performnud></rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum></up,broadcast,running,simplex,multicast>

doktornotor

@Jamerson:

can you direct me how to create the bridg between the two LAN ?

Huh?! You already have one even though you should NOT have any as there's no reason for that!


bridge0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
        ether 02:1b:ed:00:ce:00
        id 00:00:00:00:00:00 priority 32768 hellotime 2 fwddelay 15
        maxage 20 holdcnt 6 proto rstp maxaddr 100 timeout 1200
        root id 00:00:00:00:00:00 priority 32768 ifcost 0 port 0
        member: em2 flags=143 <learning,discover,autoedge,autoptp>ifmaxaddr 0 port 3 priority 128 path cost 20000
        member: em1 flags=143 <learning,discover,autoedge,autoptp>ifmaxaddr 0 port 2 priority 128 path cost 20000</learning,discover,autoedge,autoptp></learning,discover,autoedge,autoptp></up,broadcast,running,simplex,multicast>

Are you actually listening to what people are writing here? WHY do you want to create yet another bridge? :o

Jamerson

@doktornotor:

@Jamerson:

can you direct me how to create the bridg between the two LAN ?

Huh?! You already have one even though you should NOT have any as there's no reason for that!


bridge0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
        ether 02:1b:ed:00:ce:00
        id 00:00:00:00:00:00 priority 32768 hellotime 2 fwddelay 15
        maxage 20 holdcnt 6 proto rstp maxaddr 100 timeout 1200
        root id 00:00:00:00:00:00 priority 32768 ifcost 0 port 0
        member: em2 flags=143 <learning,discover,autoedge,autoptp>ifmaxaddr 0 port 3 priority 128 path cost 20000
        member: em1 flags=143 <learning,discover,autoedge,autoptp>ifmaxaddr 0 port 2 priority 128 path cost 20000</learning,discover,autoedge,autoptp></learning,discover,autoedge,autoptp></up,broadcast,running,simplex,multicast>

Are you actually listening to what people are writing here? WHY do you want to create yet another bridge? :o

i already answer this will be for testing, thank you .

LAN1 is production and LAN2 is for testing

doktornotor

Well, dude… this goes nowhere. WHAT are you testing with a setup that is totally FUBARed and you refuse any advise to get it fixed? You already bridged 2 out of 3 LANs, so what else do you want to bridge and WHY? . Like, some real reason what you expect from that. No, "it's for testing" is NOT any reason that makes sense. You have already tested that your setup does not work.

johnpoz

And you would not "bridge" between "production" and "testing".. You might bridge between physical segment that you need to extend into different locations - using 1 address network block. You would not bridge 2 different networks segments. That is utter nonsense..

And as already pointed out you already have one - which you say you didn't create.. WTF dude?? delete it - or better yet. Just wipe this pfsense vm completely and start over with a download iso you boot your new vm to and install. You should have nice clean setup with what you want to do it like 5 minutes top.. Out of the box you have to do like 3 things - set your wan static, change your lan to your ip range you want to use vs the default 192.168.1.0/24 and then create your 2nd segment and put in the any any firewall rule on this lan2 segment. There your done!!

Then you can start testing - what I have no idea..

Jamerson

@johnpoz:

And you would not "bridge" between "production" and "testing".. You might bridge between physical segment that you need to extend into different locations - using 1 address network block. You would not bridge 2 different networks segments. That is utter nonsense..

And as already pointed out you already have one - which you say you didn't create.. WTF dude?? delete it - or better yet. Just wipe this pfsense vm completely and start over with a download iso you boot your new vm to and install. You should have nice clean setup with what you want to do it like 5 minutes top.. Out of the box you have to do like 3 things - set your wan static, change your lan to your ip range you want to use vs the default 192.168.1.0/24 and then create your 2nd segment and put in the any any firewall rule on this lan2 segment. There your done!!

Then you can start testing - what I have no idea..

John thank you so much for your continu support.
i will use a Physicall NIC to LAN 2.
really appreciate all your support guys.
and apologies if i caused any furstration !

johnpoz

Physical nic?? What?? Dude are you on medication or something?