503 - Service Not Available
-
Hello,
I'm want to test wifi with snapshot release: pfSense-LiveCD-2.2-DEVELOPMENT-amd64-20140605-1701
But if I want to access the web interface to config some stuff is get: 503 - Service Not Available.
My WAN en LAN interfaces are up and running. pfSense is running more of less because I can use the internet form my LAN.
How can I help to debug is issue? My final go is to test as much as possible with the wifi capabilities
-
Same here. Was working fine and suddely, this problem. Updated to last update via console without succes. I will try a factory reset.
-
In system log:
testpfs22 check_reload_status: Could not connect to /var/run/php-fpm.socketCan't make a cat or tail on lighttpd log. The output is really long and the output is garbage.
-
A little more,
If I try to start php-fpm, I get this error.
[01-Oct-2014 11:53:20] ERROR: failed to open configuration file '/usr/local/etc/php-fpm.conf': No such file or directory (2)
[01-Oct-2014 11:53:20] ERROR: failed to load configuration file '/usr/local/etc/php-fpm.conf'
[01-Oct-2014 11:53:20] ERROR: FPM initialization failed -
Ok, found the config file at /usr/local/lib/php-fpm.conf but the're a error about wheel group not found.
Should I add wheel or use a other group for php-fpm ? Is it normal that wheel is missing ? I see in a PFSense 2.1 that wheel and a lot of other group are there will on my 2.2 test, there a really short list of group:
$FreeBSD: src/etc/master.passwd,v 1.39 2004/08/01 21:33:47 markm Exp $
#
root:$1$Z/1X26p8$***************Qm7r/:0:0::0:0:Charlie &:/root:/bin/sh
toor::0:0::0:0:Bourne-again Superuser:/root:
daemon::1:1::0:0:Owner of many system processes:/root:/usr/sbin/nologin
operator::2:5::0:0:System &:/:/usr/sbin/nologin
bin::3:7::0:0:Binaries Commands and Source:/:/usr/sbin/nologin
tty::4:65533::0:0:Tty Sandbox:/:/usr/sbin/nologin
kmem::5:65533::0:0:KMem Sandbox:/:/usr/s
all::1998:root
admins::1999:root
unbound::59:Thanks
-
Finaly edited php-fpm.conf to change user to www and group to daemon. Web interface seem to work fine now.
-
New update available. I upgrade it and now, the php-fpm.conf file seem to be generated automaticly. Not sure if it was the same before update but I think I rebooted it without problem before last update. The file always come back with root user (that can't be use with php-fpm from the error message I get) and wheel group don't exist.
Not sure how to fix it now since it seem to be generated automaticly by PFSense.
Also, it's a install on a hard drive installed from iso, not a read-only embedded install.
cat /etc/fstab # Device Mountpoint FStype Options Dump Pass# /dev/ada0s1a / ufs rw 1 1 mount /dev/ada0s1a on / (ufs, local) devfs on /dev (devfs, local) /dev/md0 on /var/run (ufs, local) devfs on /var/dhcpd/dev (devfs, local) -
Just seen this issue happen on my 2.2 rc 1/16/15 64 bit system.. Figures something always breaks
-
well i had a similar issue where web gui would say service unavailable on the below thread
https://forum.pfsense.org/index.php?topic=86572.0 -
Since SSH goes down after reboot from first upgrade when it works.. I can not get in ssh just use the local monitor and keyboard to the machine. Also noted that system failed to give me IP. I tried using the upgrade from console hoping this would fix it but didn't work. Did upgrade or reinstall install same version I think but still didn't fix it. 2.1 was so much more stable than this version