Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    Successful Install on Watchguard Firebox X700!

    Hardware
    151
    690
    857.6k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • B
      boblmartens
      last edited by

      Was able to get it up and running today after scrounging an old/ancient 5GB IDE drive from one of the dead laptops in the office. After I had it working I decided to reload the 2GB CF card and then try it again … with no luck.

      I am using a Kingston 2GB CF card and while I can get it to load on the machine that I originally installed it on, I cannot get it to load in the Firebox for the life of me. BSD starts up so that I can open up Hyperterminal and take a look at what is coming back to me, but when it starts to load the root partition, it doesn't seem to want to load off of the CF card even though I go ahead and choose ad0 as the mount device.

      Any help or ideas would be appreciated. Could it be the Kingston card I am using? Any ideas?

      1 Reply Last reply Reply Quote 0
      • B
        boblmartens
        last edited by

        I got it working, just had to read on how to install to a CF card .. I glossed over a couple of things.

        Now to try and clean some stuff up and get some other things working! Really impressed so far and looking forward to seeing what can be done with it. I now need to try and find a better CF card to use in the box … probably something a little bit faster.

        1 Reply Last reply Reply Quote 0
        • S
          secure.boy
          last edited by

          i have for sale Watchguard x700 (1.2GHz celeron, 256MB SDRAM, 512MB CF)
          contact me at secure[dot]boy[at]hotmail[dot]com or pm

          1 Reply Last reply Reply Quote 0
          • G
            gpapaiko
            last edited by

            Hi,

            I have a watchguard x1000 and got pfsense 1.2.2 working on it (on hard disk).
            Since this boxes have a LCD display and 4 button I was wondreing if anyone manged to ge the LCD diaply and buttons working.
            If so how.

            Also it has a encryption safe net card -  what command can i run to see if it has been picked and reccoginsed by pfsense.

            Thansk
            George.

            1 Reply Last reply Reply Quote 0
            • J
              jjgoessens
              last edited by

              Hi,

              Here it is :
              http://forum.pfsense.org/index.php/topic,7920.45.html#lastPost

              i installed it on a pf 1.2.3, but it should work with 1.2.2.

              ridnhard19 wrote the display driver, i just added keybord & backlight functions.

              JJ

              1 Reply Last reply Reply Quote 0
              • E
                emigrating
                last edited by

                Has anyone tried installing pfSense on one of the later model X550e or X750e Fireboxes?
                My X700 is still going strong, but I'm really starting to feel the need for a GbE firewall.

                1 Reply Last reply Reply Quote 0
                • U
                  Unubtanium
                  last edited by

                  @emigrating:

                  Has anyone tried installing pfSense on one of the later model X550e or X750e Fireboxes?
                  My X700 is still going strong, but I'm really starting to feel the need for a GbE firewall.

                  Have not yet, but as soon as my hands land on one of this i WILL give it a go.  ;D

                  1 Reply Last reply Reply Quote 0
                  • W
                    whaskes
                    last edited by

                    hi all! sorry my englisgh…. ::)

                    i installed the FreeBSD whaskes.homedns.org 7.2-RELEASE-p5 FreeBSD 7.2-RELEASE-p5 #0: Sun Dec  6 23:20:31 EST 2009    sullrich@FreeBSD_7.2_pfSense_1.2.3_snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.7  i386

                    i have a problem. when the system is booting, this messages wrote.

                    Dec 27 11:11:56 whaskes kernel: ad0: TIMEOUT - READ_DMA retrying (1 retry left) LBA=38416719
                    Dec 27 11:12:01 whaskes kernel: ad0: TIMEOUT - READ_DMA retrying (0 retries left) LBA=38416719
                    Dec 27 11:12:06 whaskes kernel: ad0: FAILURE - READ_DMA timed out LBA=38416719
                    Dec 27 11:12:06 whaskes kernel: g_vfs_done():ad0s1a[READ(offset=19669319680, length=114688)]error = 5

                    the system is working. how shall I remove the messages?

                    intel stl-2 mainboard
                    2x512mb sdram ecc-reg
                    2x1ghz pentium cpu
                    maxtor 40gb winchester

                    1 Reply Last reply Reply Quote 0
                    • W
                      wallabybob
                      last edited by

                      It is not uncommon to see messages about disk errors during startup.

                      I'd be inclined to check if your hard drive has a bad spot around the block reported. If so, it might be time to replace the hard drive. Alternatively, if you are a bit more adventurous, you might be able to adjust the partitions to remove the bad block(s) out of any active partition. This would allow you to fairly safely continue using the drive until further bad blocks show up. As best I know, the startup doesn't methodically read the hard drive at startup so I suspect the reported block is in or close to some significant directory or home block.

                      1 Reply Last reply Reply Quote 0
                      • T
                        tehtrk
                        last edited by

                        @Dayblade:

                        @Sifter:

                        Again, has anyone upgraded the memory on these boxes and gotten it to see the additional?  I placed a 512meg module in the box, and it still registers at 256meg.  I tried 2 separate sticks.

                        Perhaps jumper settings somewhere on the board?

                        Upgraded it to 512 MB just this week:

                        Kingston KVR100x64C2/512 512MB PC100 CL2

                        Also changed out the heatsink and fan - that is the MAJORITY of the noise factor in the x700 - they use a fan designed by Y.S. Tech (?) that was pushing 7200+ RPM's.  I switched and installed a lower/larger fan combo @ 5500 RPM's and temps dropped by 10C and the noise is SUBJECTIVELY quieter.
                        (Granted I did not test decibel levels prior to the fan switch out)

                        Hope that helps - <3 pfSense on my WatchGuard btw - still working on getting the LCD to do its thang…otherwise, it works like a champ.

                        Dayblade

                        Thanks for the detailed info man. I'm looking to upgrade both ram and heatsink. I think I'll just play it safe and go with the ram you mentioned. Do you have the model number for that YS tech HSF? Sounds like it's performing well.

                        Apart from low ram (when running snort lol) and that whine I'm loving this WG pfsense box!

                        1 Reply Last reply Reply Quote 0
                        • L
                          lilrichie
                          last edited by

                          Hey Everyone,

                          I am new here been looking into pfsense for some time now and getting a hombrew modification or something pre-built but then i ran accross this thread, is their a guide to installing pfsense on a firebox? if their is i am going to buy one.

                          Richard

                          N00B Still Learning….Bitten Of More Than I Can Chew But Want To Give It A Go!

                          1 Reply Last reply Reply Quote 0
                          • H
                            hlouie
                            last edited by

                            Now I got myself a WatchGuard x500 and would like to install m0n0 or pfsense.  I see some are using CF (Compact Flash), Microdrives in the CF slot, DOM (Disk on modules), IDE Hard Drive, IDE SSD (Solid State Drive).

                            I want to start off with m0n0 because it a small load but I want to grow in to using pfsense and use the full complete load.  I've read somewhere CF have limited writeback due to the bandwidth so it uses a ramdisk.  Does this apply to the Microdrive in the CF slot?  I really don't want to use a IDE Hard Drive due to noise and heat.  In the IDE, I might use a DOM or SSD.

                            Because I'm starting fresh with this new firewall, what is the best media to use so I expand in to?

                            1 Reply Last reply Reply Quote 0
                            • W
                              wallabybob
                              last edited by

                              I've been running a full install (not embedded) on a 1GB Transcend DOM for nearly two years now without problems.

                              I believe a microdrive is a magnetic drive. A Compact Flash card uses semiconductor storage. Not all microdrives work with FreeBSD - search the forums for more information.

                              1 Reply Last reply Reply Quote 0
                              • C
                                coldfire
                                last edited by

                                Hi,
                                I sell my Firebox X700 (currently under m0n0, cause of 128MB CF) with standard components and a 512MB SDRAM (not tested).
                                I've only the box, screws, m0n0 CF and Watchguard CF (no CD, no license).

                                For more information : hotfire.fraggeur@free.fr

                                1 Reply Last reply Reply Quote 0
                                • J
                                  jonnytabpni
                                  last edited by

                                  Was the watchdog timeout issue ever resolved? What about in the latest 2.0 BETA builds?

                                  1 Reply Last reply Reply Quote 0
                                  • G
                                    gpapaiko
                                    last edited by

                                    Hi,

                                    I have installed Pfsense 1.2.3RC on a Firebos X1000, on a 40Gb 2.5" IDE drive, got the LCD display working and now have some across a time out.
                                    re1: watchdog timeout -  this occures almost instantnousely wen I try to access the web interface. :(
                                    Has any one sen this before and does any one have a resolution to it.
                                    This slows all connection right down.
                                    I putit into production and with in 2 day it shows up gain.

                                    I have added a Broadcom BCM4318KFB9 wireless card, but it is not seen by pfsense -  is ther any drivers for it?
                                    What card is the best to user?

                                    Does any one if the "Safenet" encrytption card is ued by pfsense -  i know it is pickup on boot.

                                    Thanks
                                    George ;D

                                    1 Reply Last reply Reply Quote 0
                                    • G
                                      gpapaiko
                                      last edited by

                                      Hi,

                                      Made some changes and boot wiht "boot -v" option and now go this  (more details):
                                      re1: watchdog timeout
                                      t_delta 16.0218ab2579e66da0 too long

                                      Any ideas on how to resolve?

                                      Thanks
                                      George

                                      1 Reply Last reply Reply Quote 0
                                      • I
                                        iFloris
                                        last edited by

                                        @gpapaiko, I think that t_delta might be connected to the harddrive rather than to the watchguard. I found this: http://old.nabble.com/Thinkpad-T23-60-second-stall-on-resuming-8.0-RELEASE-i386-td26765321.html which references the same timeout. Someone else also has the t_delta too long message on a completely different system here: http://kerneltrap.org/mailarchive/freebsd-current/2009/7/12/6182173.
                                        Also, da0 is a bsd-reference for your harddrive.

                                        one layer of information
                                        removed

                                        1 Reply Last reply Reply Quote 0
                                        • J
                                          jonnytabpni
                                          last edited by

                                          So I got my x700, which looks perfect!

                                          However, as soon as I access the web interface, watchdog timeouts are thrown all over the place :(

                                          Anyone have a fix? Does using the embedded kernel or full kernel make a difference? I'm using BETA 2.0 on the embedded kernel

                                          1 Reply Last reply Reply Quote 0
                                          • J
                                            jlepthien
                                            last edited by

                                            Awesome! Also got a working FBX700 here now. Will look for a WLAN card and a 512MB PC133 RAM. Does anyone know how many Watts this baby consumes?

                                            | apple fanboy | music lover | network and security specialist | in love with cisco systems |

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post