Successful Install on Watchguard Firebox X700!
-
Ok, some more debugging info from the aforementioned firebox 1, but this one is a tricky one, I have absolutely no logical explanation for it:
First a little network schematic:
LAN (re1) <--- 172.20.2.1/24 ---> Firebox 1 <--- WAN (re0) using public x.x.x.x/28 subnet ---> SWITCH <---> The internet <---> Laptop at remote location |_> linux server in same /28 subnet
(I hope this is clear, the linux server is connected to the same switch as the WAN port of the firebox, the /28 subnet consists of public internet ip addresses)
Yesterday I was doing some tests on when the watchdog errors occur, from my laptop at the remote location.
pfsense Webgui is running on HTTPS, port 443 so I opened up the HTTPS port and icmp ping replies on the WAN side of the firewall.
I'm continuously running a ping from the laptop to the WAN IP of the firebox.
As soon as I told firefox on my laptop to connect to the firebox WAN ip through https, firefox shows me the http authentication dialog, I fill in the fields and press OK, and the firebox WAN ip immediately stops responding to ping requests.
Firefox tries to load the page but stays blank (since the firebox obviously stopped sending data), as soon as I press the STOP button in firefox the firebox WAN ip address starts replying to PING requests again.So far you'd think the http process is causing the problem, but now it starts to get really strange:
I open up an SSH session to the linux box in the same public /28 internet range as the firebox, and tunnel a https connection through the SSH connection.
In other words, I mapped a tcp port on my laptop to one on the linux server so that from the firebox point of view my requests to open up the web interface come from the linux server in its own WAN subnet.
And now, opening up the web interface works perfectly right away. I see the pfsense interface, can click around in all menu's, don't get any timeouts and don't get any watchdog errors in the logs… The public WAN ip also keeps responding to the still running ping requests.So I tried to open the web interface from my laptop over the internet through the real public IP again, and again the watchdog errors occurs and the firebox stops responding to network traffic...
I'm not making any sense of this...
-
Thanks for the help trying to solve this, but I'm afraid I'm running out of time to fix this.
I've replaced both fireboxes with 'normal' pc's, exported and imported the config, and all problems have disappeared.I'm not giving up on the watchguard hardware yet, but I don't have the time to keep looking for a solution right now.
-
ugh.. just had to add a few rules to the firewall and it ended up being a multi-reboot network outage due to watchdog timeout freezeups.. box had been up for a couple weeks, transferring tens of gigs of data per day, but soon as I need to poke around the webgui, the lan interface decides to puke all over itself
- 2 months later
-
ugh.. just had to add a few rules to the firewall and it ended up being a multi-reboot network outage due to watchdog timeout freezeups.. box had been up for a couple weeks, transferring tens of gigs of data per day, but soon as I need to poke around the webgui, the lan interface decides to puke all over itself
Hey Valhalla1,
This is what i've been battling with now for a number of weeks. There is an issue with the driver support in Freebsd and with the 8139C+ RealTek chip used for the network card's in this box. Its been a real headache trying to figure out. I'll be pulling mine out of the main network and setting it off to the side soon but have been trying a number of things.
What I've done so far:
-Update pfSense to use the 6.3 RELEASE of freebsd didn't help
-Update the pfSense to use the 6-Current (latest 6.3) drivers for the realtek network controller (re)
-Disabled ACPI - as I had thought this fixed it a while ago but I was fooled
-I'm out of ideas. -
ugh.. just had to add a few rules to the firewall and it ended up being a multi-reboot network outage due to watchdog timeout freezeups.. box had been up for a couple weeks, transferring tens of gigs of data per day, but soon as I need to poke around the webgui, the lan interface decides to puke all over itself
Hey Valhalla1,
This is what i've been battling with now for a number of weeks. There is an issue with the driver support in Freebsd and with the 8139C+ RealTek chip used for the network card's in this box. Its been a real headache trying to figure out. I'll be pulling mine out of the main network and setting it off to the side soon but have been trying a number of things.
What I've done so far:
-Update pfSense to use the 6.3 RELEASE of freebsd didn't help
-Update the pfSense to use the 6-Current (latest 6.3) drivers for the realtek network controller (re)
-Disabled ACPI - as I had thought this fixed it a while ago but I was fooled
-I'm out of ideas.well I appreciate the efforts, I got into pfsense really due to seeing this original post and just had to get me one of these pretty red boxes. managed to snag one on ebay for $51.. a fantastic value considering I paid twice that a few years ago for a 486 cpu soekris with half the network interfaces. fwiw it works great as long as I don't need to use the webgui a lot. also I (usually) dont have to reboot pfsense when it happens if I hit stop on the browser and close the tab and wait a few second
are the realtek drivers in freebsd 7 any different than the 6.3 RELEASE drivers?jmcentire said he stopped getting the watchdog timeouts after switching to hp procurve switches. mine is connected to just a 24 port d-link unmanaged switch on the lan interface I get the timeouts on. maybe I'll pick up one on the cheap, wanted to play with vlans anyway
-
My timeouts went away when I upgraded my switch to one of the higher end netgear managed ones and a cisco one on my other one. I got 3 of these running now. Its sad One is a v60 that I paid over 10k for in 2002. the others are x1000 and x700 i picked up off ebay for under 200 each.
i working on doing a full install on one now using cf and a laptop drive for the paritions that write alot . Like /var/log and swap
-
Hum, you guys bring up a good point. I have an SMC managed switch which always had seemed to work well. I just changed the port configurations on the switch which the firebox is plugged into, disabling the autonegotiation for those set of ports and manually set then to full duplex 100.
I hope this will do the trick.
-
Well I tried manually setting the port speeds to 100 full-duplex in pfsense and on the SMC switch and got the same watchdog timeouts. I'm going to try a net gear switch i've got laying around and see if that does anything. I'll post back the results of that.
-
-
Anyway, if anyone else is interested in these watchguards, the X500, X700, X1000, and X2500 are all the same hardware, they just have different licenses to allow higher throughput.
It looks like the mini pci slot could be used for a wifi card, so you could choose if you wanted a vpn card or wifi card in that slot. Granted, both have to be recognized by pfsense.
-
Well I tried manually setting the port speeds to 100 full-duplex in pfsense and on the SMC switch and got the same watchdog timeouts. I'm going to try a net gear switch i've got laying around and see if that does anything. I'll post back the results of that.
any updates on that SMC switch on the watchdog timeouts ? I'm looking to buy a managed switch that works with these watchguards without the timeouts, preferably as cheap as I can get away with.
there are reports in this thread that some cisco switches had the errors, but someone else said theirs don't on cisco switches (what models?)
also netgear has been reported with the problems, but not a higher end model which got rid of the errors (which higher end model?)
my d-link causes them.. hp procurve has been mentioned as error free but not sure which models (any managed procurve switch?)looking for something I can find under $200 on ebay preferably.. what about a dell 2716 'webmanaged' switch those are cheap but support vlan, link aggregation, port mirroring..
and back to a different subject, the VPN accelerator card. anyone tried 1.3 ALPHA ALPHA pfense on their watchguard boxes ? I would but mine is in production use at the moment. maybe since its freebsd 7 it might add support for the vpn card in these watchguards?
-
The watchguard seems to have a bunch of Realtec NICs onboard.
That's where I'd expect the troubles to start…The DeLL 5224 or 5324 switches basically are rebranded SMCs.
They can be found on eBay regularly if you don't mind the additional ports. -
there are reports in this thread that some cisco switches had the errors, but someone else said theirs don't on cisco switches (what models?)
also netgear has been reported with the problems, but not a higher end model which got rid of the errors (which higher end model?)
my d-link causes them.. hp procurve has been mentioned as error free but not sure which models (any managed procurve switch?)Im using a couple Netgear GSM712's I bought off ebay. Ive tested my watchguard v60 and x700's and no timeout problems. Also I used them thru my cisco 3548xl with no problems. I do have Dell 5324's at work . which is were these firewall are headed in the end but I havent had a chance to test them on the dells.
-
thanks for those model #'s gives me some stuff to look for
-
It may be that the cheapest way ahead is to get a good brand 8 port web managed (or L2 managed) switch and hook that up to the rest of your network.
As a data point, I'm using ZyXEL level 2 switches in my very large home office network; at the moment, I've got two GS-2024 switches, which are linked by fibre. They're not HP, though they're little more than a third of the price of HP - around £350 as opposed to nearly £900 for an L2 managed 24 Gigabit port HP Procurve. There's a few rough edges, but they do work OK. I've had a fan failure which resulted in an RMA, also I had two DoA 1000BASE-SX GBICs (misshapen latch on one, no link on the other), but things have been OK since.
The biggest rough edge I know of is that there's no support for port trunking in the STP implementation; with HP you can set STP parameters for the trunk. ZyXEL doesn't support STP for trunks, though I hope it will be added in a future firmware version. That problem aside, the 3.80 firmware for the Dimension range is pretty feature rich, with new features in 3.80 including SNMPv3.
There's some new ES-2024 switches on eBay right now for just under $200 - these are 24 port Level 2 managed 10/100 plus 2 port 10/100/1000 copper or SFP devices. I suspect that's more ports than you want or could use, and I expect if you're spending that money you'd rather have fewer ports that are Gigabit. Overall, I'd expect ZyXEL to be a minority brand for switches in the US, much as their DSL routers are more common, but it's another direction that you could look in.
I have no idea about the "Watchguard problem" on these switches; my production firewall is a Dell PowerEdge R200.
-
someone asked for pictures… this is an Firebox x700
![DSC_0030 (Medium).JPG](/public/imported_attachments/1/DSC_0030 (Medium).JPG)
![DSC_0030 (Medium).JPG_thumb](/public/imported_attachments/1/DSC_0030 (Medium).JPG_thumb)
![DSC_0045 (Medium).JPG](/public/imported_attachments/1/DSC_0045 (Medium).JPG)
![DSC_0045 (Medium).JPG_thumb](/public/imported_attachments/1/DSC_0045 (Medium).JPG_thumb)
![DSC_0046 (Medium).JPG](/public/imported_attachments/1/DSC_0046 (Medium).JPG)
![DSC_0046 (Medium).JPG_thumb](/public/imported_attachments/1/DSC_0046 (Medium).JPG_thumb) -
Has anyone tried to replace the crypto mini-pci card with a wifi mini-pci card?
-
So are most of you taking the HD tray out completely? Do you know where to get a HD that fits in the bracket and slides into place using the connector?
-
So are most of you taking the HD tray out completely? Do you know where to get a HD that fits in the bracket and slides into place using the connector?
my hard drive is in the tray, which if I recall is kind of loose inside there but I had to use it, otherwise the hard drive would just be laying on the motherboard directly, and this caused a short of some kind and it wouldn't power up
a regular sized ide hard drive might fit properly in the removeable cage, the laptop ones are obv. too small -
Ive gone ahead and purchased a 4gig hitachi microdrive. Id like to use this in the x700. Can I do a full install to the microdrive from my other computer, then slide it into the cf slot in the x700?