Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    HUAWEI E1820 UMTS Stick not working pfSense

    Hardware
    2
    2
    1.2k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • M
      mrsunfire
      last edited by

      Hi!

      I'm using pfSense 2.1.5 on a PC Engines APU.1C Board. I assigned the E1820 USB UMTS stick as interface and configured PPP.

      Here is my usbconfig:

      $ usbconfig
      ugen0.1: <ohci root="" hub="" ati=""> at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE
      ugen1.1: <ehci root="" hub="" ati=""> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE
      ugen2.1: <ohci root="" hub="" ati=""> at usbus2, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE
      ugen3.1: <ehci root="" hub="" ati=""> at usbus3, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE
      ugen4.1: <ohci root="" hub="" ati=""> at usbus4, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE
      ugen5.1: <ohci root="" hub="" ati=""> at usbus5, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE
      ugen6.1: <ehci root="" hub="" ati=""> at usbus6, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE
      ugen6.2: <flash card="" readerwriter="" generic=""> at usbus6, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON
      ugen1.2: <huawei mobile="" huawei="" technologies=""> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON</huawei></flash></ehci></ohci></ohci></ehci></ohci></ehci></ohci>
      

      Also here my cua:

      $ dir /dev/cua*;dmesg
      Copyright (c) 1992-2012 The FreeBSD Project.
      Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
      	The Regents of the University of California. All rights reserved.
      FreeBSD is a registered trademark of The FreeBSD Foundation.
      FreeBSD 8.3-RELEASE-p16 #0: Mon Aug 25 08:27:41 EDT 2014
          root@pf2_1_1_i386.pfsense.org:/usr/obj.i386/usr/pfSensesrc/src/sys/pfSense_wrap.8.i386 i386
      Timecounter "i8254" frequency 1193182 Hz quality 0
      CPU: AMD G-T40E Processor (1000.00-MHz 686-class CPU)
        Origin = "AuthenticAMD"  Id = 0x500f20  Family = 14  Model = 2  Stepping = 0
        Features=0x178bfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,mmx,fxsr,sse,sse2,htt>Features2=0x802209 <sse3,mon,ssse3,cx16,popcnt>AMD Features=0x2e500800 <syscall,nx,mmx+,ffxsr,page1gb,rdtscp,lm>AMD Features2=0x35ff <lahf,cmp,svm,extapic,cr8,abm,sse4a,mas,prefetch,ibs,skinit,wdt>TSC: P-state invariant
      real memory  = 2115289088 (2017 MB)
      avail memory = 2051104768 (1956 MB)
      ACPI APIC Table: <core  coreboot="">
      FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
      FreeBSD/SMP: 1 package(s) x 2 core(s)
       cpu0 (BSP): APIC ID:  0
       cpu1 (AP): APIC ID:  1
      ioapic0 <version 2.1=""> irqs 0-23 on motherboard
      ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
      ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
      module_register_init: MOD_LOAD (ipw_bss_fw, 0xc0738f60, 0) error 1
      ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
      ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
      module_register_init: MOD_LOAD (ipw_ibss_fw, 0xc0739000, 0) error 1
      ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
      ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
      module_register_init: MOD_LOAD (ipw_monitor_fw, 0xc07390a0, 0) error 1
      wlan: mac acl policy registered
      cryptosoft0: <software crypto=""> on motherboard
      padlock0: No ACE support.
      acpi0: <core coreboot=""> on motherboard
      acpi0: [ITHREAD]
      acpi0: Power Button (fixed)
      Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
      acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
      cpu0: <acpi cpu=""> on acpi0
      cpu1: <acpi cpu=""> on acpi0
      acpi_hpet0: <high precision="" event="" timer=""> iomem 0xfed00000-0xfed003ff on acpi0
      Timecounter "HPET" frequency 14318180 Hz quality 900
      pcib0: <acpi host-pci="" bridge=""> port 0xcf8-0xcff iomem 0xa0000-0xbffff on acpi0
      pci0: <acpi pci="" bus=""> on pcib0
      pcib1: <acpi pci-pci="" bridge=""> irq 16 at device 4.0 on pci0
      pci1: <acpi pci="" bus=""> on pcib1
      re0: <realtek 8111="" 8168="" b="" c="" cp="" d="" dp="" e="" f="" pcie="" gigabit="" ethernet=""> port 0x1000-0x10ff mem 0xf7900000-0xf7900fff,0xf7800000-0xf7803fff irq 16 at device 0.0 on pci1
      re0: Using 1 MSI-X message
      re0: ASPM disabled
      re0: Chip rev. 0x2c000000
      re0: MAC rev. 0x00000000
      miibus0: <mii bus=""> on re0
      rgephy0: <rtl8169s 8110s="" 8211b="" media="" interface=""> PHY 1 on miibus0
      rgephy0:  none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
      re0: [ITHREAD]
      pcib2: <acpi pci-pci="" bridge=""> irq 17 at device 5.0 on pci0
      pci2: <acpi pci="" bus=""> on pcib2
      re1: <realtek 8111="" 8168="" b="" c="" cp="" d="" dp="" e="" f="" pcie="" gigabit="" ethernet=""> port 0x2000-0x20ff mem 0xf7b00000-0xf7b00fff,0xf7a00000-0xf7a03fff irq 17 at device 0.0 on pci2
      re1: Using 1 MSI-X message
      re1: ASPM disabled
      re1: Chip rev. 0x2c000000
      re1: MAC rev. 0x00000000
      miibus1: <mii bus=""> on re1
      rgephy1: <rtl8169s 8110s="" 8211b="" media="" interface=""> PHY 1 on miibus1
      rgephy1:  none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
      re1: [ITHREAD]
      pcib3: <acpi pci-pci="" bridge=""> irq 18 at device 6.0 on pci0
      pci3: <acpi pci="" bus=""> on pcib3
      re2: <realtek 8111="" 8168="" b="" c="" cp="" d="" dp="" e="" f="" pcie="" gigabit="" ethernet=""> port 0x3000-0x30ff mem 0xf7d00000-0xf7d00fff,0xf7c00000-0xf7c03fff irq 18 at device 0.0 on pci3
      re2: Using 1 MSI-X message
      re2: ASPM disabled
      re2: Chip rev. 0x2c000000
      re2: MAC rev. 0x00000000
      miibus2: <mii bus=""> on re2
      rgephy2: <rtl8169s 8110s="" 8211b="" media="" interface=""> PHY 1 on miibus2
      rgephy2:  none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
      re2: [ITHREAD]
      pcib4: <acpi pci-pci="" bridge=""> irq 19 at device 7.0 on pci0
      pci4: <acpi pci="" bus=""> on pcib4
      ath0: <atheros 9280=""> mem 0xf7e00000-0xf7e0ffff irq 19 at device 0.0 on pci4
      ath0: [ITHREAD]
      [ath] enabling AN_TOP2_FIXUP
      ath0: AR9280 mac 128.2 RF5133 phy 13.0
      atapci0: <ati 800="" ixp700="" sata300="" controller=""> port 0x4010-0x4017,0x4020-0x4023,0x4018-0x401f,0x4024-0x4027,0x4000-0x400f mem 0xf7f08000-0xf7f083ff irq 19 at device 17.0 on pci0
      atapci0: [ITHREAD]
      atapci0: AHCI v1.20 controller with 6 6Gbps ports, PM supported
      ata2: <ata channel=""> at channel 0 on atapci0
      ata2: [ITHREAD]
      ata3: <ata channel=""> at channel 1 on atapci0
      ata3: [ITHREAD]
      ata4: <ata channel=""> at channel 2 on atapci0
      ata4: [ITHREAD]
      ata5: <ata channel=""> at channel 3 on atapci0
      ata5: [ITHREAD]
      ata6: <ata channel=""> at channel 4 on atapci0
      ata6: [ITHREAD]
      ata7: <ata channel=""> at channel 5 on atapci0
      ata7: [ITHREAD]
      ohci0: <ohci (generic)="" usb="" controller=""> mem 0xf7f04000-0xf7f04fff irq 18 at device 18.0 on pci0
      ohci0: [ITHREAD]
      usbus0: <ohci (generic)="" usb="" controller=""> on ohci0
      ehci0: <ehci (generic)="" usb="" 2.0="" controller=""> mem 0xf7f08400-0xf7f084ff irq 17 at device 18.2 on pci0
      ehci0: [ITHREAD]
      usbus1: EHCI version 1.0
      usbus1: <ehci (generic)="" usb="" 2.0="" controller=""> on ehci0
      ohci1: <ohci (generic)="" usb="" controller=""> mem 0xf7f05000-0xf7f05fff irq 18 at device 19.0 on pci0
      ohci1: [ITHREAD]
      usbus2: <ohci (generic)="" usb="" controller=""> on ohci1
      ehci1: <ehci (generic)="" usb="" 2.0="" controller=""> mem 0xf7f08500-0xf7f085ff irq 17 at device 19.2 on pci0
      ehci1: [ITHREAD]
      usbus3: EHCI version 1.0
      usbus3: <ehci (generic)="" usb="" 2.0="" controller=""> on ehci1
      pci0: <serial bus,="" smbus=""> at device 20.0 (no driver attached)
      isab0: <pci-isa bridge=""> at device 20.3 on pci0
      isa0: <isa bus=""> on isab0
      pcib5: <acpi pci-pci="" bridge=""> at device 20.4 on pci0
      pci5: <acpi pci="" bus=""> on pcib5
      ohci2: <ohci (generic)="" usb="" controller=""> mem 0xf7f06000-0xf7f06fff irq 18 at device 20.5 on pci0
      ohci2: [ITHREAD]
      usbus4: <ohci (generic)="" usb="" controller=""> on ohci2
      pcib6: <acpi pci-pci="" bridge=""> at device 21.0 on pci0
      pci6: <acpi pci="" bus=""> on pcib6
      ohci3: <ohci (generic)="" usb="" controller=""> mem 0xf7f07000-0xf7f07fff at device 22.0 on pci0
      ohci3: [ITHREAD]
      usbus5: <ohci (generic)="" usb="" controller=""> on ohci3
      ehci2: <ehci (generic)="" usb="" 2.0="" controller=""> mem 0xf7f08600-0xf7f086ff at device 22.2 on pci0
      ehci2: [ITHREAD]
      usbus6: EHCI version 1.0
      usbus6: <ehci (generic)="" usb="" 2.0="" controller=""> on ehci2
      acpi_button0: <power button=""> on acpi0
      atrtc0: <at realtime="" clock=""> port 0x70-0x71 irq 8 on acpi0
      orm0: <isa option="" rom=""> at iomem 0xee800-0xeffff pnpid ORM0000 on isa0
      ata0: <ata channel=""> at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
      ata0: [ITHREAD]
      ata1: <ata channel=""> at port 0x170-0x177,0x376 irq 15 on isa0
      ata1: [ITHREAD]
      ppc0: <parallel port=""> at port 0x378-0x37f irq 7 on isa0
      ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
      ppc0: [ITHREAD]
      ppbus0: <parallel port="" bus=""> on ppc0
      ppi0: <parallel i="" o=""> on ppbus0
      uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
      uart0: [FILTER]
      uart0: console (9600,n,8,1)
      uart1: <16550 or compatible> at port 0x2f8-0x2ff irq 3 on isa0
      uart1: [FILTER]
      acpi_throttle0: <acpi cpu="" throttling=""> on cpu0
      acpi_throttle1: <acpi cpu="" throttling=""> on cpu1
      acpi_throttle1: failed to attach P_CNT
      device_attach: acpi_throttle1 attach returned 6
      RTC BIOS diagnostic error ff <clock_battery,rom_cksum,config_unit,memory_size,fixed_disk,invalid_time>Timecounters tick every 10.000 msec
      IPsec: Initialized Security Association Processing.
      usbus0: 12Mbps Full Speed USB v1.0
      usbus1: 480Mbps High Speed USB v2.0
      ugen0.1: <ati> at usbus0
      uhub0: <ati 1="" 9="" ohci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr=""> on usbus0
      ugen1.1: <ati> at usbus1
      uhub1: <ati 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr=""> on usbus1
      usbus2: 12Mbps Full Speed USB v1.0
      usbus3: 480Mbps High Speed USB v2.0
      ugen2.1: <ati> at usbus2
      uhub2: <ati 1="" 9="" ohci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr=""> on usbus2
      ugen3.1: <ati> at usbus3
      uhub3: <ati 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr=""> on usbus3
      usbus4: 12Mbps Full Speed USB v1.0
      usbus5: 12Mbps Full Speed USB v1.0
      ugen4.1: <ati> at usbus4
      uhub4: <ati 1="" 9="" ohci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr=""> on usbus4
      ugen5.1: <ati> at usbus5
      uhub5: <ati 1="" 9="" ohci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr=""> on usbus5
      usbus6: 480Mbps High Speed USB v2.0
      uhub0: 5 ports with 5 removable, self powered
      ugen6.1: <ati> at usbus6
      uhub6: <ati 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr=""> on usbus6
      uhub4: 2 ports with 2 removable, self powered
      uhub2: 5 ports with 5 removable, self powered
      uhub5: 4 ports with 4 removable, self powered
      uhub1: 5 ports with 5 removable, self powered
      uhub3: 5 ports with 5 removable, self powered
      uhub6: 4 ports with 4 removable, self powered
      ugen6.2: <generic> at usbus6
      umass0: <generic 0="" 2="" flash="" card="" readerwriter,="" class="" 0,="" rev="" 2.01="" 1.00,="" addr=""> on usbus6
      ugen1.2: <huawei technologies=""> at usbus1
      ugen1.2: <huawei technologies=""> at usbus1 (disconnected)
      SMP: AP CPU #1 Launched!
      da0 at umass-sim0 bus 0 scbus0 target 0 lun 0
      da0: <multiple card ="" reader="" 1.00=""> Removable Direct Access SCSI-4 device 
      da0: 40.000MB/s transfers
      da0: 7580MB (15523840 512 byte sectors: 255H 63S/T 966C)
      Trying to mount root from ufs:/dev/da0s1a
      WARNING: / was not properly dismounted
      ZFS NOTICE: Prefetch is disabled by default on i386 -- to enable,
                  add "vfs.zfs.prefetch_disable=0" to /boot/loader.conf.
      ZFS WARNING: Recommended minimum kmem_size is 512MB; expect unstable behavior.
                   Consider tuning vm.kmem_size and vm.kmem_size_max
                   in /boot/loader.conf.
      ZFS filesystem version 5
      ZFS storage pool version 28
      ugen1.2: <huawei technologies=""> at usbus1
      u3g0: <huawei 0="" 2="" technologies="" huawei="" mobile,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr=""> on usbus1
      u3g0: Found 4 ports.
      umass1: <huawei 0="" 2="" technologies="" huawei="" mobile,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr=""> on usbus1
      umass2: <huawei 0="" 2="" technologies="" huawei="" mobile,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr=""> on usbus1
      (probe0:umass-sim1:1:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 
      (probe0:umass-sim1:1:0:0): CAM status: SCSI Status Error
      (probe0:umass-sim1:1:0:0): SCSI status: Check Condition
      (probe0:umass-sim1:1:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
      (probe1:umass-sim2:2:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 
      (probe1:umass-sim2:2:0:0): CAM status: SCSI Status Error
      (probe1:umass-sim2:2:0:0): SCSI status: Check Condition
      (probe1:umass-sim2:2:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
      cd0 at umass-sim1 bus 1 scbus1 target 0 lun 0
      cd0: <huawei mass="" storage="" 2.31=""> Removable CD-ROM SCSI-2 device 
      cd0: 40.000MB/s transfers
      cd0: Attempt to query device size failed: NOT READY, Medium not present
      da1 at umass-sim2 bus 2 scbus2 target 0 lun 0
      da1: <huawei tf="" card="" storage=""> Removable Direct Access SCSI-2 device 
      da1: 40.000MB/s transfers
      da1: Attempt to query device size failed: NOT READY, Medium not present
      wlan0: changing name to 'ath0_wlan0'
      re1: link state changed to DOWN
      re1: link state changed to UP
      re2: link state changed to DOWN
      ng0: changing name to 'ppp0'
      DUMMYNET 0 with IPv6 initialized (100409)
      load_dn_sched dn_sched FIFO loaded
      load_dn_sched dn_sched QFQ loaded
      load_dn_sched dn_sched RR loaded
      load_dn_sched dn_sched WF2Q+ loaded
      load_dn_sched dn_sched PRIO loaded
      re2: link state changed to UP
      pflog0: promiscuous mode enabled
      ath0: stuck beacon; resetting (bmiss count 6)
      ath0: stuck beacon; resetting (bmiss count 0)
      ipfw2 (+ipv6) initialized, divert loadable, nat loadable, rule-based forwarding enabled, default to accept, logging disabled
      ng0: changing name to 'ppp0'
      ng0: changing name to 'ppp0'
      ng0: changing name to 'ppp0'
      ng0: changing name to 'ppp0'
      ng0: changing name to 'ppp0'
      re0: link state changed to DOWN
      ng0: changing name to 'ppp0'
      ng0: changing name to 'ppp0'
      ng0: changing name to 'ppp0'
      ng0: changing name to 'ppp0'
      ng0: changing name to 'ppp0'
      ng0: changing name to 'ppp0'</huawei></huawei></huawei></huawei></huawei></huawei></multiple></huawei></huawei></generic></generic></ati></ati></ati></ati></ati></ati></ati></ati></ati></ati></ati></ati></ati></ati></clock_battery,rom_cksum,config_unit,memory_size,fixed_disk,invalid_time></acpi></acpi></parallel></parallel></parallel></ata></ata></isa></at></power></ehci></ehci></ohci></ohci></acpi></acpi></ohci></ohci></acpi></acpi></isa></pci-isa></serial></ehci></ehci></ohci></ohci></ehci></ehci></ohci></ohci></ata></ata></ata></ata></ata></ata></ati></atheros></acpi></acpi></rtl8169s></mii></realtek></acpi></acpi></rtl8169s></mii></realtek></acpi></acpi></rtl8169s></mii></realtek></acpi></acpi></acpi></acpi></high></acpi></acpi></core></software></version></core ></lahf,cmp,svm,extapic,cr8,abm,sse4a,mas,prefetch,ibs,skinit,wdt></syscall,nx,mmx+,ffxsr,page1gb,rdtscp,lm></sse3,mon,ssse3,cx16,popcnt></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,mmx,fxsr,sse,sse2,htt>
      

      On Status Interfaces I see:

      UMTS interface (ppp0)
      Status	up
      PPP	 
      Uptime	00:00:0
      Cell Signal (RSSI)	rssi:15 level:-83dBm percent:48%
      Cell Mode	None, No Service Mode
      Cell SIM State	Valid SIM State
      Cell Service	Valid Service
      MAC address	00:00:00:00:00:00
      IPv6 Link Local	fe80::20d:b9ff:fe33:910%ppp0	 
      In/out packets	0/0 (0 bytes/0 bytes)
      In/out packets (pass)	0/0 (0 bytes/0 bytes)
      In/out packets (block)	0/9 (0 bytes/660 bytes)
      In/out errors	0/0
      Collisions	0
      
      

      System logs PPP shows:

      Nov 26 23:23:04	ppp: [opt3_link0] Link: reconnection attempt 7 in 1 seconds
      Nov 26 23:23:04	ppp: [opt3_link0] LCP: Down event
      Nov 26 23:23:04	ppp: [opt3_link0] Link: DOWN event
      Nov 26 23:23:04	ppp: [opt3_link0] MODEM: Fail to open serial port /dev/cuau0 on speed 115200
      Nov 26 23:23:04	ppp: [opt3_link0] uu_lock(cuau0): read error: File exists
      Nov 26 23:23:02	ppp: [opt3_link0] Link: reconnection attempt 6
      Nov 26 23:23:01	ppp: [opt3_link0] Link: reconnection attempt 6 in 1 seconds
      Nov 26 23:23:01	ppp: [opt3_link0] LCP: Down event
      Nov 26 23:23:01	ppp: [opt3_link0] Link: DOWN event
      Nov 26 23:23:01	ppp: [opt3_link0] MODEM: Fail to open serial port /dev/cuau0 on speed 115200
      Nov 26 23:23:01	ppp: [opt3_link0] uu_lock(cuau0): read error: File exists
      Nov 26 23:23:00	ppp: [opt3_link0] Link: reconnection attempt 5
      Nov 26 23:22:58	ppp: [opt3_link0] Link: reconnection attempt 5 in 2 seconds
      Nov 26 23:22:58	ppp: [opt3_link0] LCP: Down event
      Nov 26 23:22:58	ppp: [opt3_link0] Link: DOWN event
      

      What do you guys think is the problem?

      Netgate 6100 MAX

      1 Reply Last reply Reply Quote 0
      • ?
        Guest
        last edited by

        Your PPP stuff shows cuaU0 and it needs to be cuaU0.2

        ugen1.2: <huawei technologies="">at usbus1
        u3g0: <huawei 0="" 2="" technologies="" huawei="" mobile,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr="">on usbus1
        u3g0: Found 4 ports.
        umass1: <huawei 0="" 2="" technologies="" huawei="" mobile,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr="">on usbus1
        umass2: <huawei 0="" 2="" technologies="" huawei="" mobile,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr="">on usbus1

        Nov 26 23:23:04 ppp: [opt3_link0] MODEM: Fail to open serial port /dev/cuau0 on speed 115200

        Good luck and let us know if fixed.</huawei></huawei></huawei></huawei>

        1 Reply Last reply Reply Quote 0
        • First post
          Last post
        Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.