Pfsense setting up LAN to connect to DD-WRT router
bc00l last edited by
Hello, I am having some trouble getting my PFSense Device and a dd-wrt Router to connect to the internet.
If I set LAN on PFSENSE to 192.168.1.0 /24
I have set the router IP to 192.168.1.2.
Connected the Router port 1 to PFSENSE Lan Port.
Should I be able to connect to the internet of am I doing something wrong?
Or should I set the routers WAN settings to connect to the PFSENSE LAN as a gateway?
The most current PFSENSE is on a NETGATE APU2 Device with a WAN, LAN, and OPT port. (Note the appliance is working and everything checks out)
Networking Setup for both devices, described to the best of my abilities, I can provide more info if needed.
WAN is set to (DHCP) and successfully pulls an IP from my ISP. (Physically connected from WAN to Router)
LAN is set to use 192.168.1.1, netmask 255.255.255.0. DHCP is disabled here. No IPV6. Selected No to use Upstream Internet Gateway.
***note the purpose I disabled DHCP on the PFSENSE LAN port is because I would only like it as a gateway to the internet and not handing out IPs.
ROUTER: This Router has 5 ports( 1 WAN-Intenet port) 4 LAN ports
WAN port is disabled. It has the option to autoconfigure connection, set to static and a lot of other options that might not be relevant.
Router is set to use static IP of 192.168.1.2, Netmask of 255.255.255.0 Gateway of 192.168.1.1, Local DNS 192.168.1.1- Never was sure if local dns was necessary.
Router is also set as DHCP server
192.168.1.5-25 addressess available.
These are my settings, I tried to be as thorough as possible. This has been frustrating, and after finding lots a similar examples but none specifically for what I am doing, I thought I will ask you guys.
Thank you in advance.
nzimmers last edited by
If you want the dd-wrt router to hand out IP addresses you need to connect the router wan port to the pfsense lan port.
very simply, if you want the dd-wrt router and all the connected machines on the same subnet as the Pfsense lan port you cannot run the dd-wrt router with DHCP - so DHCP would need to be done on the pfsense lan port.
see this page: http://www.dd-wrt.com/wiki/index.php/Wireless_Access_Point
Wolf666 last edited by
I use my R7000 (running DD-WRT) as access point, connected to pfSense Lan-Lan. On DD-WRT disable DHCP, NAT and firewall, let pfSense do them.
doktornotor Banned last edited by
You do NOT want DHCP server on your DD-WRT. http://www.dd-wrt.com/wiki/index.php/Wireless_Access_Point#Long_Version
I agree with what's been said above, you're almost certainly better off having pfSense handle DHCP. However…...
I expect the reason it doesn't work is that the DD-WRT box is handing out it's own address (192.168.1.2) as a gateway for the connected clients via DHCP. This can't work with it connected as you have it. It must hand out the pfSense LAN address (192.168.1.1) as a gateway instead.
Wolf666 last edited by
As Steve mentioned, in the DD-WRT you must set the correct gateway, the pfSense LAN IP.
Importantly not the gateway for the dd-wrt box itself but whatever it's handing out as a gateway via dhcp for clients.
I don't actually know if that's a user setting in dd-wrt. :-
Edit: Looks like you have to add it as a dhcp-option. Really just letting pfSense handle DHCP woukd be much easier.