DHCP Server Setup with a Layer 3 Switch
-
And why put host routes on all your boxes?? When all you have to do is use a transit network to connect your downstream router to your edge router and your done..
-
Intention was to have pfSense handle DHCP etc to VLAN1 and VLAN2 as well. Cannot be done with one transit network, right?
-
No it can not be dhcp unless it has an IP in the interface.. So run a different dhcp server ;)
host routing on every host he has, so he can run dhcp on pfsense seem like a really bad trade off to me.. Especially since I have never seen a L3 switch that didn't have dhcp as a feature.. So just run it at the switch..
If he is a AD shop he should be running dhcp on his AD anyway, etc.. What advantage is there to running it on pfsense in a scenario that is not supported, so you going to have to put host routes on every box or your hairpinning.
There are always multiple ways to skin the cat, doesn't mean some of them are good ideas ;)
-
This setup is so basic that we seem to lose the big picture.
One APU, one L3 switch with 2 segments. DHCP (and probably DNS etc as well) for both segments.
This probably is the most basic +1 setup all of us can imagine.Now add inter-VLAN routing at the L3 switch to it and we cannot come up with a solution that does not need additional hardware? Come on!
-
Now add inter-VLAN routing at the L3 switch to it and we cannot come up with a solution that does not need additional hardware? Come on!
People have already come with a solution. That solution has turned into bitrot for absolutely inexplicable reason.
Patch has conflicts and cannot be merged. Can you please re-submit and I'll take care of testing and get it merged. Sorry for the long delay
No shit, Sherlock. After 1,5 year it can no longer be automatically merged? Shocking. No, seriously. It was already resubmitted once and once again ignored for another 6 months. You suppose people will keep resubmitting every half year, they don't have better things to do with their time for sure.
-
What extra hardware? The L3 switch I am quite sure can hand out some dhcp addresses ;)
As to why this is not a current feature of pfsense I would guess its not a really needed feature by the majority of the user base.. Normally you would have pfsense do your intervlan routing - this also added feature of full firewall features that many L3 switches would lack.
Would it be nice feature - sure it would come in handy for this sort of scenario.
If your so large that that your wanting to handle intervlan at a L3 switch, then your prob so large that your already running a dhcp server be it AD or not, etc. Which again reduces the actual need of pfsense being able to handle this specific sort of scenario.
Kind of a special case if you ask me, large enough network that you need multiple vlans but no firewall between them and so much traffic between them that your pfsense box does not handle it well, etc. So you want to do it at L3 switch - but you still want to run dhcp on your edge router/firewall?
I would think the best solution for this OP is just use 1 segment so just doing L2 and pfsense can be his dhcp server, etc. But he has not given details to why he need 2 segments or even if doing any ACLs at the switch between them, etc. Would really need a lot of devices to have vlans to shrink your broadcast domains, etc.d
I don't think the devs or even the users expect pfsense to be all things for all scenarios.. In a scenario where your running down stream L3 switches and pfsense is your edge I don't really think pfsense being your dhcp server is a huge userbase..
-
pfSense, as it is now, does not do this. To come up with cockamamie schemes involving putting static routes on hosts just to use the pfSense DHCP server is just ludicrous.
As has been mentioned, the switch probably does DHCP on its L3 VIFs.
-
What extra hardware? The L3 switch I am quite sure can hand out some dhcp addresses ;)
As to why this is not a current feature of pfsense I would guess its not a really needed feature by the majority of the user base.. Normally you would have pfsense do your intervlan routing - this also added feature of full firewall features that many L3 switches would lack.
Would it be nice feature - sure it would come in handy for this sort of scenario.
If your so large that that your wanting to handle intervlan at a L3 switch, then your prob so large that your already running a dhcp server be it AD or not, etc. Which again reduces the actual need of pfsense being able to handle this specific sort of scenario.
Kind of a special case if you ask me, large enough network that you need multiple vlans but no firewall between them and so much traffic between them that your pfsense box does not handle it well, etc. So you want to do it at L3 switch - but you still want to run dhcp on your edge router/firewall?
I would think the best solution for this OP is just use 1 segment so just doing L2 and pfsense can be his dhcp server, etc. But he has not given details to why he need 2 segments or even if doing any ACLs at the switch between them, etc. Would really need a lot of devices to have vlans to shrink your broadcast domains, etc.d
I don't think the devs or even the users expect pfsense to be all things for all scenarios.. In a scenario where your running down stream L3 switches and pfsense is your edge I don't really think pfsense being your dhcp server is a huge userbase..
I was looking for hte same working with some l3 switches. it will be an option at pfsense at some point.
=)
