Moving from Smoothwall
-
Very old but still works like a charm: http://hp.vector.co.jp/authors/VA002416/teraterm.html ;)
-
Thank you for that. Managed to work out that i must start putty and have connected up before starting the firewall up. i Have 2 NIC's however pfsense is only picking one up. This is what I get:
Valid interfaces are:
xl0 00:06:5b:c2:f5:8b
Do you want to set up VLANs first?
If you are not going to use VLANs, or only for optional interfaces, you should
say no here and use the webConfigurator to configure VLANs later, if required.Do you want to set up VLANs now [y|n]?
from a screenshot i took of smoothwall I had the NIC so called 3c59x with mac 00:06:5B:C2:F5:8B and sk98lin with mac 00:12:17:5A:E1:F6. the 3c59x is the onboard one and the sk98lin is the pci one.
does this mean the sk98lin is not compatible? can I get drivers installed on this? If not what compatible one would work (for like £5 on ebay).
-
does this mean the sk98lin is not compatible? can I get drivers installed on this? If not what compatible one would work (for like £5 on ebay).
yes,no (as in not easy),best is intel
Supported nic's http://www.freebsd.org/releases/6.2R/hardware-i386.html#ETHERNETIf you already have a vlan switch, then one nic is enough.
-
would either of these be ok?
http://cgi.ebay.co.uk/Realtek-RTL8139-810x-Family-Fast-Ethernet-10-100-NIC_W0QQitemZ300218693618QQihZ020QQcategoryZ51195QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
http://cgi.ebay.co.uk/Netgear-FA311-PCI-Network-Adapter-10Base-T-100Base-TX_W0QQitemZ220227059468QQihZ012QQcategoryZ51195QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
don't mention the exact model number on the list however their is a FA311-TX and RTL8139C+. A lot of the items do not specify model numbers and the card needs to fit into a half height slot (i just take the metal faceplate off for it to fit)
-
Can't say, the same goes for
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=310045020042&ih=021&category=51195&ssPageName=STORE:PROMOBOX:NEWLIST#ebayphotohosting
But if i play poker…........ ;) -
I have purchased the two Intel ones. Hopefully all will go well. I used a seperate CF card for pfsense so I am not without firewall while I am waiting for the NIC. :)
-
Hi, NIC's arrived today and seem to supported. I have configured the firewall with the correct interfaces for the WAN/LAN plugged in. However when i have configured and changed the ip settings for the LAN (already have server on 192.168.1.1), it will not load on http://192.168.1.200/ even after a restart. I get "The document contains no data" as a firefox error.
I reset the settings and tried again with no luck. I have attached the configuration I used which was just copied from my putty session.
-
To be certain: You DO have a VLAN cappable switch do you?
Because frankly i'm asking myself what you need these VLAN's for :) -
VLAN switch? not sure. I have computers which are connected to my Netgear GS605 switch. That is connected to the firewall which is connected to the router (BT Home hub which will be changed soon).
With smoothwall i just had the 2 interfaces, one configured as Red (WAN) and Green (LAN) with all my network settings. I have atatched the screenshot of the smoothwall network config (although the RED nic has changed to the intel one now).
-
Aha, worked it out. Said no to the VLAN and continued with the same settings. I can now access the web interface. Thanks GruensFroeschli ;D
