Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    Dynamic and static IP for WAN

    Routing and Multi WAN
    2
    6
    4373
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • H
      hammaskejju
      last edited by

      Hello!

      I have one WAN interface with DHCP. Now I want to add static IP to the same interface so I cou'd see my router from LAN side.

      Earlier, when I ran SmoothWall I just wrote a line:
      ipconfig eth1:1 192.168.1.2 netmask 255.255.255.0 etc
      And route
      route -host 192.168.1.2 eth1:1
      route -net 192.168.1.0 netmask 255.255.255.0 eth1:1

      After this I cou'd establish connection to my ZyXel Prestige ADSL modem.

      How could I do the same with  pfSense?

      1 Reply Last reply Reply Quote 0
      • GruensFroeschliG
        GruensFroeschli
        last edited by

        I suppose you're looking for a workaround to get access to the ADSL modem on WAN.

        try to use the search:
        http://forum.pfsense.org/index.php?action=search
        keywords: "access modem PPPoE"

        –> http://forum.pfsense.org/index.php/topic,5727.msg34562.html#msg34562

        We do what we must, because we can.

        Asking questions the smart way: http://www.catb.org/esr/faqs/smart-questions.html

        1 Reply Last reply Reply Quote 0
        • H
          hammaskejju
          last edited by

          > keywords: "access modem PPPoE"

          Somehow I think this is not the question here. I don't even know exactly, what the PPPoE is anyway..
          Usually it's not a workaround to add static IP with a dynamic one - it is well-konwn way to gain access to modem.
          It's just so simple to add in Linux with few lines in shell…

          1 Reply Last reply Reply Quote 0
          • GruensFroeschliG
            GruensFroeschli
            last edited by

            Well maybe you should make it more clear what you are trying to achieve and what you already have.

            What does your modem do? Is it a bridge? Is it a router? why does it have an IP if it's a bridge?
            What kind of IP do you already have on you WAN? public IP? IP from a DHCP on your modem? IP directly from your ISP (if the modem is a bridge), but then why do you have an IP on the modem?

            @http://en.wikipedia.org/wiki/PPPoE:

            PPPoE, Point-to-Point Protocol over Ethernet, is a network protocol for encapsulating Point-to-Point Protocol (PPP) frames inside Ethernet frames. It is used mainly with ADSL services where individual users connect to the ADSL transceiver (modem) over Ethernet and in plain Metro Ethernet networks.

            Also even if you dont have a PPPoE type WAN, the link i posted would help you to redirect traffic for a certain IP range to the WAN (which you'd know, if you read the thread….).

            We do what we must, because we can.

            Asking questions the smart way: http://www.catb.org/esr/faqs/smart-questions.html

            1 Reply Last reply Reply Quote 0
            • H
              hammaskejju
              last edited by

              Well maybe you should make it more clear what you are trying to achieve and what you already have

              Well ok then.

              I have a modem which is configured as a bridge. It has an IP address: 192.168.1.1

              My pfSense wall get's public IP from ISP

              Now pfSense is connected to the Internet thru modem with real public IP. With public I mean an IP, which is not routed thru NAT.

              –---

              Now I need to add a static IP to WAN interface. For example, if  I put IP: 192.168.1.2 I can communicate to router and configure and see stats etc.

              This is very simple to do in Linux: just add an IP alias to NIC with ipconfig
              ipconfig eth0 would be the native NIC. It get's an IP address from ISP with DHCP.
              If I type: ifconfig eth0:0 192.168.1.2 I can put a static IP address next to dynamic one. Now I have one address from ISP and one of my own (the static).

              Was I clear enoug? This stuff is somewhat hard to explain...

              1 Reply Last reply Reply Quote 0
              • GruensFroeschliG
                GruensFroeschli
                last edited by

                Well i already posted the solution in my first reply :)

                http://forum.pfsense.org/index.php/topic,5727.msg34562.html#msg34562

                We do what we must, because we can.

                Asking questions the smart way: http://www.catb.org/esr/faqs/smart-questions.html

                1 Reply Last reply Reply Quote 0
                • First post
                  Last post