PC Engines apu2 experiences
-
I'm still running the 160311 that the board shipped with without issue. If it aint broke don't fix it.
-
4.0.7 is indeed the latest as far as I am aware. Maybe the way that they note the updates here makes more sense? Looks like they were using the date and now they've switched to actual version numbers.
I was also running 160311 up until yesterday, didn't really have any issues either.
FYI, this is the changelog for 4.0.7:
coreboot https://github.com/pcengines/coreboot/blob/coreboot-4.0.x/CHANGELOG.md reduced log level: display mainboard, DRAM and ECC info only improved SD card performance forced to use SD in 2.0 mode reset J17 GPIO's (NCT5104D) during boot to inputs update sortbootorder to v4.0.3 (UART C/D toggling) mPCIe1 working with ASM1061 based sata controllers (mPCIe2 still not working) fixed RAM size displaying during the boot (for 2GB sku's) iPXE (no changelog available yet) added autoboot command seabios https://github.com/pcengines/seabios/blob/coreboot-4.0.x/CHANGELOG.md allowed for one-time PXE boot with N key enable/disable option for USB boot enable/disable option for PXE boot sortbootorder https://github.com/pcengines/sortbootorder/blob/coreboot-4.0.x/CHANGELOG.md EHCI0 controller disable/enable option UART C and D toggling memtest86+ https://github.com/pcengines/memtest86plus/blob/coreboot-4.0.x/CHANGELOG.md refreshed procedure, so that full screen content is reprinted on refresh macro SPD_DISABLED for disabling SPD related functionality refresh option label (l) to bottom menu -
Ah, well spotted Veldkornet, the BIOS naming makes sense after all! Thanks for your reply, and also to Jailer. Jailer, I fully understand your 'if it aint broke…' sentiment, very wise if you have had systems running for some time with no issues. However, I don't have any run-time behind me with any APU2 BIOS so I'm going to assume that PCEngines know what they are doing and flash my two new boards with 4.0.7.
Right... now I need to work out how to get pfSense onto a 16GB mSATA SSD! I've always used CF cards with nanobsd images - I just pop a fresh card into a CF card reader connected to my Windows laptop and use physdiskwrite to push the image onto the 4GB CF card. I then pop the CF card into the Alix board and I'm ready to configure pfSense. My problem now is that I don't have an mSATA slot in anything but the new APU2 board - can you get a USB adapter with an mSATA slot? I think the PCEngines support site has instructions on how to use the APU2 to burn the image to mSATA, have you guys done that for your systems at all?
Also, I've always used nanobsd images which have worked just great out in the field - about 30 pfSense systems with nanobsd on CF for up to six years and not a single issue! The CF cards were mostly cheap Kingston units (I now use Sandisk btw) so nanobsd made sense to avoid burning out the read/write cycle limit. I now have the PCEngines 16GB mSATA for the APU2 which should, I presume, have wear leveling so might not need to worry about wear and can finally install full version. I know I can still use nanobsd on the mSATA drives, but just wondered what other people have been doing. The one big advantage I see with a full/normal (non-nanobsd) install is that it opens up the world of installed packages at a future date.
Thanks again
Ian -
I have a 256GB M2 SSD. I just used rufus to create a USB installer, booted from the USB with a console cable and installed.
Is this what you were asking?
-
Mine still says PC Engines APU2 after the update to 2.3.4.
Yeah, mine did too. I more meant after the latest firmware update.
Can you post the output of
/bin/kenv -q smbios.system.product /bin/kenv -q smbios.system.makerwith the 4.0.7 FW.
-
For my APU2C2 board with v4.0.7 BIOS:
/bin/kenv -q smbios.system.product : APU2
/bin/kenv -q smbios.system.maker : PC Engines -
For my APU2C2 board with v4.0.7 BIOS:
/bin/kenv -q smbios.system.product : APU2
/bin/kenv -q smbios.system.maker : PC EnginesSame for me
-
OK, used to be lowercase. Easy fix. https://github.com/pfsense/pfsense/pull/3724
-
OK, used to be lowercase. Easy fix. https://github.com/pfsense/pfsense/pull/3724
Cool, thanks! 8)
-
Right… now I need to work out how to get pfSense onto a 16GB mSATA SSD!
Create a bootable USB drive and install to SATA drive. It really is that simple.
-
For my APU2C4 board with v4.0.7 BIOS:
/bin/kenv -q smbios.system.product : APU2
/bin/kenv -q smbios.system.maker : PC Engines -
Have recently upgraded my apu2b4 to 2.4 RC.
Prior to the upgrade I used the flashrom utility to upgrade BIOS to v4.0.7.
For my configuration (LAN, WLAN + dual WAN) it was a smooth upgrade - kudos to pfSense team!
Some updated OpenSSL benchmarks, showing GCM performance improvement (ready for OpenVPN 2.4):
openssl speed -elapsed -evp aes-128-cbc type 16 bytes 64 bytes 256 bytes 1024 bytes 8192 bytes aes-128-cbc 121916.58k 174865.28k 214507.52k 226282.50k 230230.70k openssl speed -elapsed -evp aes-128-gcm type 16 bytes 64 bytes 256 bytes 1024 bytes 8192 bytes aes-128-gcm 43423.18k 113562.28k 276355.50k 358399.32k 431721.13k -
Hi. I'm coming late to the party and bought an APU2C4 board, running the latest 2.40RC based on FreeBSD 11.1. I'm using the full install on an mSATA board. BIOS v4.0.7
I read every post in the thread… How many of these tweaks (from the defaults) are still needed on the latest pfSense?
- Temperature probe changes
- PowerD
- Trim support
- Hardware TCP & large receive offload changes
- AES-NI changes
Also, do you recommend the 32-bit or 64-bit version for this platform?
Thanks!
-
Hi. I'm coming late to the party and bought an APU2C4 board, running the latest 2.40RC based on FreeBSD 11.1. I'm using the full install on an mSATA board. BIOS v4.0.7
I read every post in the thread… How many of these tweaks (from the defaults) are still needed on the latest pfSense?
- Temperature probe changes
- PowerD
- Trim support
- Hardware TCP & large receive offload changes
- AES-NI changes
Also, do you recommend the 32-bit or 64-bit version for this platform?
Thanks!
It;s a 64 bit processor, so what do you think? :)
-
Not sure. It only has 4GB RAM, and some 32-bit operating systems are faster.
How about those other things?
-
I'm using the full install on an mSATA board. BIOS v4.0.7
Would be also my personal choice and is also highly recommended from netgate in their Version 2.4.0 blog.
_A few noteworthy items about running or upgrading to 2.4:-
32-bit x86 and NanoBSD have been deprecated and are not supported on 2.4. Hardware capable of
running 64-bit images should be reinstalled with a 64-bit version. -
NanoBSD installs on 64-bit hardware should be reinstalled as a full installation.
-
32-bit x86 hardware can continue to run pfSense software version 2.3.x, which will
receive security updates for at least a year after 2.4.0-RELEASE._
I read every post in the thread… How many of these tweaks (from the defaults) are still needed on the latest pfSense?
You don´t need to setup tune or organize something, but you cold do so and that is more a additional option for the
admins and nothing you must be pressed to do.- Temperature probe changes
Do you need the temperature sensor?
- PowerD
Is the cpu scaling from the lowest bottom to the highest top as needed by default?
- Trim support
Is this a mSATA or SSD that supports TRIM?
- Hardware TCP & large receive offload changes
Is all running fine without any issues, like you was imagine it?
- AES-NI changes
Are you using the OpenVPN or IPSec VPN method?
Some need it, some want it and some are aware of doing something in that direction!
Also, do you recommend the 32-bit or 64-bit version for this platform?
Since version 2.4.0 there will be only the amd64Bit version and ARM images only!!!
- no NanoBSD
- no 32Bit OS image
- AES-NI support in the CPU is a must be since version 2.5.0
Not sure. It only has 4GB RAM, and some 32-bit operating systems are faster.
Today this information is really outdated, it was due to the changing between 32Bit and 64Bit hardware
where 64Bit hardware were brand new on the marked, but today you may better of using the 64Bit image
if you have real 64Bit hardware, due to many differences likes;- drivers will be not even ported back to 32Bit hardware (due to the lag of time and from the hardware side)
- nearly any new hardware will be 64Bit and is more capable as the older 32Bit technic
- since the ARM support other things are gone, or we all must waiting a longer time to get updates/upgrades
How about those other things?
pfSense 2.4.0 blog
_A few noteworthy items about running or upgrading to 2.4:-
32-bit x86 and NanoBSD have been deprecated and are not supported on 2.4.
Hardware capable of running 64-bit images should be reinstalled with a 64-bit version. -
NanoBSD installs on 64-bit hardware should be reinstalled as a full installation.
-
32-bit x86 hardware can continue to run pfSense software version 2.3.x, which will
receive security updates for at least a year after 2.4.0-RELEASE._
-
-
Not sure. It only has 4GB RAM, and some 32-bit operating systems are faster.
How about those other things?
It uses very little RAM. As my tag says APU2C4. I've never seen RAM usage over 30% and I use pfBlocker too, run my own web and mail servers too. 2Gb would probably be sufficient.
It works perfectly well with a default install. With the fact it supports AES you can enable that… or not, it's optional but enable it anyway.
As has been said already 32bit is deprecated anyway.
It's a really good device and takes only minutes to install and set up pfSense from scratch.
-
Do you need the temperature sensor?
Yep
Is the cpu scaling from the lowest bottom to the highest top as needed by default?
Not sure. It was talked about in this thread. Do I?
Is this a mSATA or SSD that supports TRIM?
Of course.
- Hardware TCP & large receive offload changes
Is all running fine without any issues, like you was imagine it?
Of course, but maybe it can run better, which is obviously why I asked.
- AES-NI changes
Are you using the OpenVPN or IPSec VPN method?
Of course, that's why I asked.
-
I noticed today that the APU2 makes a quick short beep every time I login via the GUI.
Have I just never noticed this or is it new in 2.4.0?
-
I noticed today that the APU2 makes a quick short beep every time I login via the GUI.
Have I just never noticed this or is it new in 2.4.0?
Mine always did this from SSH via the speaker on the computer running putty but it's new for me the speaker of the apu2 device now beeps kind-a cool really
