22.01 Reinstall goes wrong

stephenw10

Ok, I think the issue here is that the installer for some reason did not update uboot.

What was unclear last night was where this error was happening. I incorrectly assumed it was when you were trying to boot the USB stick which would only be the wrong image as I said bit was this in fact after appearing to install successfully and then trying to boot the result from eMMC?

If that's the case it's because uboot did not update for some reason and the older uboot cannot boot from ZFS.
Check the uboot version show at boot. If it's still the older version it will show as:

U-Boot 2017.03-armada-17.10.2-g6a6581a-dirty (Nov 01 2018 - 16:04:57 -0300)

If that is the case you should still be able to install as UFS and boot that.

Steve

KOM

@stephenw10 Yes it still shows the older version of Uboot, and as you guessed reinstalling with UFS works fine. I've reported back to Netgate and will update when I hear something from them.

stephenw10

Does it show that exact uboot version or one from Nov 22nd 2018? There might be a clue here...

KOM

@stephenw10

U-Boot 2017.03-armada-17.10.2-g6a6581a-dirty (Nov 01 2018 - 16:04:57 -0300)

stephenw10

Ok, that might be the issue. If you can please run the following command:

[22.01-RELEASE][admin@1100-3.stevew.lan]/root: sh -c 'dd if=/dev/flash/spi0 bs=64k count=1 2>/dev/null | sha256'
6eeae92008003686d912066830858e4af0fa8476b23a719c10f60e1edfb8cfeb

The updater checks for known sha256 sums and it appears yours may not be expected. That is the updated uboot shown on my 1100 here.

One you have booted into 22.01 using UFS though you should be able to manually update uboot and then re-install ZFS if that turns out to be the issue.

Steve

KOM

@stephenw10 My output is 1b6998c83988bb0e53500606d340d119f07846e4058afb8eb55c3eca07ffbcef

How does one manually update U-Boot?

stephenw10

If you repeat that command does it come back the same every time?

KOM

@stephenw10 Yes

stephenw10

Confirming this locally....

KOM

@stephenw10 Should I leave my unit untouched in case you need to refer to something or is it ok for me to proceed getting it working with UFS? I rely on this for VPN to work access and it needs to be up & ready by Thursday evening.

rcoleman-netgate

@kom I would just get it back online for your VPN. We're working on tracking down a unit that has this same UBoot internally.

stevie_0815

@rcoleman-netgate

Hi,

I have a recently purchased SG-1100 and requested the new firmware so that i could start working with a ZFS-based install. I'm getting the same error on my device:

U-Boot 2017.03-armada-17.10.2-g6a6581a-dirty (Nov 01 2018 - 16:04:57 -0300)
...
ERROR: cannot open /boot/lua/loader.lua: invalid argument.

Should i just wait for a new recovery firmware to be released or what is the guidance?
I'm just starting out learning pfSense so it's not a big deal to wait a little while...

Thanks,
Stevie.

KOM

@stevie_0815 Install with UFS. When the fix comes out, you can backup your config, reinstall with ZFS, then restore your config. Boom, done.

stevie_0815

@kom Thanks for the lightning fast response, will do as suggested.. Maybe a naive question but any idea about the fix ETA? Not (yet) familiar with how quickly this stuff gets turned around.

KOM

@stevie_0815 No.

rcoleman-netgate

@stevie_0815 We're looking into a fix.