SG-1100 Mini PCIe slot - purpose?

stephenw10

Ooo good point, the jumpers do still exist. Looking back at my notes I had no hardware to test it.

However there is no SIM slot wired to it which most (all?) modem cards would require. I guess you might be able to use one of those adapter cards with SIM slot in it....

Steve

netrace

Resuming this thread exactly 1 year old: is it possible to point me where is located the wire jumper in the board? I do really need LTE connection as mini PCIe, and I only miss the USB interface on the Mini PCIe.

Giorgio

stephenw10

Hmm, I'd have to look into it again but I don't believe you can as I said a year ago.
However there is now some support for the PCI bus in 2.4.5. Actual card support may vary but you might find wifi cards now work there.

Steve

stephenw10

With the WLE200NX for example:

[2.4.5-RELEASE][root@1100-3.stevew.lan]/root: pciconf -lv
ath0@pci0:0:0:0:        class=0x028000 card=0x3099168c chip=0x002a168c rev=0x01 hdr=0x00
    vendor     = 'Qualcomm Atheros'
    device     = 'AR928X Wireless Network Adapter (PCI-Express)'
    class      = network

netrace

Thanks Steve!
This is a very good news!

However, the usb interface is not wired to the pci. I see many wire jumpers on the board, are you aware of any circuit board schematic I can looking into?

stephenw10

The USB jumpers (J16 and J19) are there so you should be able to switch the connections from the external port to the mPCIe slot. However I cannot find the modem I know I have to test it with right now. I've installed in something but can't for the life of me remember what.
I should point out that while I would expect any issues doing this it would be an untested/unsupported setup. There are no antenna holes so you would need to get creative.

Steve

netrace

@stephenw10 Thanks so much, I'll try this week and let you know!

stephenw10

Found my modem! It works:

[2.4.5-RELEASE][root@1100-3.stevew.lan]/root: usbconfig
ugen0.1: <Marvell XHCI root HUB> at usbus0, cfg=0 md=HOST spd=SUPER (5.0Gbps) pwr=SAVE (0mA)
ugen1.1: <Marvell EHCI root HUB> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA)
ugen1.2: <Sierra Wireless, Incorporated Mini Card> at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON (0mA)

ugen1.2: <Sierra Wireless, Incorporated Mini Card> at usbus1
u3g0 on uhub1
u3g0: <Data Interface> on usbus1
u3g0: Found 3 ports.

[2.4.5-RELEASE][root@1100-3.stevew.lan]/dev: cu -l cuaU0.0
Connected
at
OK
ati
Manufacturer: Sierra Wireless, Inc.
Model: MC8775
Revision: H1_1_9_3MCAP C:/WS/FW/H1_1_9_3MCAP/MSM6280/SRC 2007/12/12 11:49:21
IMEI: 013265502503099
IMEI SV: 10
FSN: D611748126531
3GPP Release 5
+GCAP: +CGSM,+FCLASS,+DS


OK

Just move the two jumpers near the USB port (J16+J19) to their alternate positions.

Steve

stephenw10

Of course I've just realised there's no SIM slot. So you would need one of those SIM card adapters.

Edit: Memory not good then! https://forum.netgate.com/post/833230

Steve

daemonix

hello,

Im trying to add a 2.4G PCIE (mikrotik) to the 1100 and boot stops at pci0. I have moved the 2 jumpers as above.

TIM-1.0
WTMI-devel-18.12.1-1a13f2f
WTMI: system early-init
SVC REV: 5, CPU VDD voltage: 1.213V
NOTICE:  Booting Trusted Firmware
NOTICE:  BL1: v1.5(release):1f8ca7e-dirty (Marvell-devel-18.12.2)
NOTICE:  BL1: Built : 10:16:46, Oct 13 2021
NOTICE:  BL1: Booting BL2
NOTICE:  BL2: v1.5(release):1f8ca7e-dirty (Marvell-devel-18.12.2)
NOTICE:  BL2: Built : 10:16:50, Oct 13 2021
NOTICE:  BL1: Booting BL31
NOTICE:  BL31: v1.5(release):1f8ca7e-dirty (Marvell-devel-18.12.2)
NOTICE:  BL31: Built : 10

U-Boot 2018.03-devel-18.12.3-gc9aa92c-dirty (Oct 13 2021 - 10:14:54 -0300)

Model: Netgate 1100
       CPU     1200 [MHz]
       L2      800 [MHz]
       TClock  200 [MHz]
       DDR     750 [MHz]
DRAM:  1 GiB
Comphy chip #0:
Comphy-0: USB3          5 Gbps    
Comphy-1: PEX0          2.5 Gbps  
Comphy-2: SATA0         6 Gbps    
SATA link 0 timeout.
AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
flags: ncq led only pmp fbss pio slum part sxs 
PCIE-0: Link up
MMC:   sdhci@d0000: 0, sdhci@d8000: 1
Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB, total 4 MiB
OK
Model: Netgate 1100
Net:   eth0: neta@30000 [PRIME]
Hit any key to stop autoboot:  0 
|          __                                               
    _ __  / _|___  ___ _ __  ___  ___      _                
   | '_ \| |_/ __|/ _ \ '_ \/ __|/ _ \   _| |_              
   | |_) |  _\__ \  __/ | | \__ \  __/  |_   _|             
   | .__/|_| |___/\___|_| |_|___/\___|    |_|               
   |_|                                                      
                                                            
                                                                              
 ╔════ Welcome to Netgate pfSense Plus ════╗      __________________________  
 ║                                         ║     /                       ___\ 
 ║  1. Boot Multi user [Enter]             ║    |                      /`     
 ║  2. Boot Single user                    ║    |                     /    :-|
 ║  3. Escape to loader prompt             ║    |      _________  ___/    /_ |
 ║  4. Reboot                              ║    |    /` ____   / /__    ___/ |
 ║  5. Cons: Serial                        ║    |   /  /   /  /    /   /     |
 ║                                         ║    |  /  /___/  /    /   /      |
 ║  Options:                               ║    | /   ______/    /   /  _    |
 ║  6. Kernel: default/kernel (1 of 2)     ║    |/   /          /   / _| |_  |
 ║  7. Boot Options                        ║        /          /___/ |_   _| |
 ║  8. Boot Environments                   ║       /                   |_|   |
 ║                                         ║      /_________________________/ 
 ╚═════════════════════════════════════════╝                                  \
   Autoboot in 0 seconds. [Space] to pause

Loading kernel...
/boot/kernel/kernel text=0x2a8 text=0x9a8fac text=0x25bee4 data=0x12ea238 data=0x0+0x2d58fe syms=[0x8+0x183288+0x8+0x1492f3]
Loading configured modules...
/boot/kernel/opensolaris.ko text=0x1217 text=0xc88 data=0x448+0x6830 syms=[0x8+0xfc0+0x8+0x88e]
/boot/kernel/zfs.ko text=0x8a548 text=0x1313f8 data=0x18400+0x909a0 syms=[0x8+0x26670+0x8+0x1fab0]
can't find '/etc/hostid'
can't find '/boot/entropy'
Using DTB provided by EFI at 0x8000000.
---<<BOOT>>---
Copyright (c) 1992-2021 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 12.3-STABLE plus-RELENG_22_05-n202700-3ddaea61055 pfSense arm64
FreeBSD clang version 13.0.0 (git@github.com:llvm/llvm-project.git llvmorg-13.0.0-0-gd7b669b3a303)
VT: init without driver.
real memory  = 1073680384 (1023 MB)
avail memory = 1003532288 (957 MB)
Starting CPU 1 (1)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
arc4random: WARNING: initial seeding bypassed the cryptographic random device because it was not yet seeded and the knob 'bypass_before_seeding' was enabled.
wlan: mac acl policy registered
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xffff000000214d60, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffff000000214e10, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffff000000214ec0, 0) error 1
iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_bss_fw, 0xffff000000214f70, 0) error 1
iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_ibss_fw, 0xffff000000215020, 0) error 1
iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_monitor_fw, 0xffff0000002150d0, 0) error 1
random: entropy device external interface
WARNING: Device "g_ctl" is Giant locked and may be deleted before FreeBSD 14.0.
MAP 8000000 mode 2 pages 5
MAP 3e61f000 mode 2 pages 1
MAP 3ffc6000 mode 2 pages 1
WARNING: Device "openfirm" is Giant locked and may be deleted before FreeBSD 14.0.
WARNING: Device "pci" is Giant locked and may be deleted before FreeBSD 14.0.
[ath_hal] loaded
WARNING: Device "kbd" is Giant locked and may be deleted before FreeBSD 14.0.
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
simplebus1: <Flattened device tree simple bus> on simplebus0
simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0x13800-0x138ff,0x13c00-0x13c1f on simplebus1
simple_mfd1: <Simple MFD (Multi-Functions Device)> mem 0x18800-0x188ff,0x18c00-0x18c1f on simplebus1
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
gic0: <ARM Generic Interrupt Controller v3.0> mem 0x1d00000-0x1d0ffff,0x1d40000-0x1d7ffff,0x1d80000-0x1d81fff,0x1d90000-0x1d91fff,0x1da0000-0x1dbffff irq 27 on simplebus1
gpio0: <Armada 37x0 North Bridge GPIO Controller> mem 0x13800-0x138ff,0x13c00-0x13c1f irq 28,29,30,31,32,33,34,35,36,37,38,39 on simple_mfd0
gpiobus0: <OFW GPIO bus> on gpio0
gpio1: <Armada 37x0 South Bridge GPIO Controller> mem 0x18800-0x188ff,0x18c00-0x18c1f irq 40,41,42,43,44 on simple_mfd1
gpiobus1: <OFW GPIO bus> on gpio1
gpioregulator0: <GPIO controlled regulator> on ofwbus0
generic_timer0: <ARMv8 Generic Timer> irq 0,1,2,3 on ofwbus0
Timecounter "ARM MPCore Timecounter" frequency 12500000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 12500000 Hz quality 1000
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
cpu1: <Open Firmware CPU> on cpulist0
pmu0: <Performance Monitoring Unit> irq 4 on ofwbus0
spi0: <Armada 37x0 SPI controller> mem 0x10600-0x10fff irq 6 on simplebus1
iichb0: <Marvell Armada 37x0 IIC controller> mem 0x11000-0x11023 irq 7 on simplebus1
iicbus0: <OFW I2C bus> on iichb0
iic0: <I2C generic I/O> on iicbus0
uart0: <Marvell Armada 3700 UART> mem 0x12000-0x121ff irq 9,10,11 on simplebus1
uart0: console (115200,n,8,1)
gpioc0: <GPIO controller> on gpio0
syscon_generic_dev0: <syscon> mem 0x14000-0x1405f on simplebus1
gpioc1: <GPIO controller> on gpio1
mvneta0: <NETA controller> mem 0x30000-0x33fff irq 14 on simplebus1
mvneta0: version is 10
mvneta0: Ethernet address: f0:ad:4e:23:33:c3
mdio0: <MDIO> on mvneta0
e6000sw0: <Marvell 88E6341> on mdio0
e6000sw0: multi-chip addressing mode (0x1)
e6000sw0: CPU port at 0
e6000sw0: fixed port at 0
e6000sw0: PHY at port 1
miibus0: <MII bus> on e6000sw0
e1000phy0: <Marvell 88E1000 Gigabit PHY> PHY 17 on miibus0
e1000phy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: PHY at port 2
miibus1: <MII bus> on e6000sw0
e1000phy1: <Marvell 88E1000 Gigabit PHY> PHY 18 on miibus1
e1000phy1:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: PHY at port 3
miibus2: <MII bus> on e6000sw0
e1000phy2: <Marvell 88E1000 Gigabit PHY> PHY 19 on miibus2
e1000phy2:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: switch is ready.
etherswitch0: <Switch controller> on e6000sw0
xhci0: <Marvell Integrated USB 3.0 controller> mem 0x58000-0x5bfff irq 16 on simplebus1
xhci0: 32 bytes context size, 32-bit DMA
usbus0 on xhci0
ehci0: <Marvell Integrated USB 2.0 controller> mem 0x5e000-0x5ffff irq 17 on simplebus1
usbus1: EHCI version 1.0
usbus1 on ehci0
sdhci_xenon0: <Armada Xenon SDHCI controller> mem 0xd0000-0xd02ff,0x1e808-0x1e80b irq 24 on simplebus1
mmc0: <MMC/SD bus> on sdhci_xenon0
sdhci_xenon1: <Armada Xenon SDHCI controller> mem 0xd8000-0xd82ff,0x17808-0x1780b irq 25 on simplebus1
mmc1: <MMC/SD bus> on sdhci_xenon1
ahci0: <AHCI SATA controller> mem 0xe0000-0xe1fff irq 26 on simplebus1
ahci0: AHCI v1.30 with 1 6Gbps ports, Port Multiplier supported with FBS
ahcich0: <AHCI channel> at channel 0 on ahci0
pcib0: <Marvell Armada 3700 PCIe Bus Controller> mem 0xd0070000-0xd008ffff irq 5 on simplebus0
pcib0: link up
pci0: <PCI bus> on pcib0

Any ideas?

EDIT: I have used the same PCIE wifi card with pfsense on a APU2C4

stephenw10

Replied in your new thread.