IPv6 Question
-
@stephenw10 exactly common config actually - pvid on a trunk is vlan X... As traffic enters the port untagged it gets put in vlan X.. Now when it leaves the switch to say the router it is tagged on vlan X.
But my same question that could explain what is happening - but doesn't explain why it doesn't work on ipv4.. Unless the firewall rules on lan on pfsense do not allow ipv4?
-
@johnpoz I have no PIVD set. No Native VLAN. Just straight Trunk. on the switch or the Host. I'm sure of it.
interface ethernet 1/25
description sm3_10G
switchport mtu 9216
switchport mode trunk
switchport trunk allowed vlan all
ipv6 nd ra suppress -
@johnnybinator said in IPv6 Question:
Just straight Trunk
And what switch allows that? If there was no native, then any untagged traffic wouldn't go anywhere - so clearly that is not what is happening.
-
@johnpoz Clearly there's nothing clear about it.
-
@johnnybinator if pfsense is handing you IPv6 address on vlan 11
LAN (lan) -> ix0.11 -> v4: 10.200.0.254/24
Then the traffic is coming to pfsense on vlan 11, how it got there would be a switch config thing. Or a client config thing.. Pfsense isn't going to say oh untagged traffic, let me put that on my ix0.11 interface..
-
Is that the trunk port that connects to pfSense or where you're connecting the client?
Or is that the same port somehow? -
@stephenw10 that’s the switch port that connects to pfSense. I think what I’m going to do next is plug a host directly into the PF sense interface.
-
Um.... so how are you connecting a client to it now?
The problem is almost certainly in the switch config for the port the client is on.
Steve
-
@stephenw10 ummm sooo….
As I’m writing this, I have a switch connected. What I was think would solve this lovely chat is if I put a host directly on the pfSense trunk.
-
Yes, that would certainly confirm if there really is something in pfSense allowing IPv6 only to leak from a VLAN to the parent.
I was just confused as to how it was connected when you were testing before. I may have misread it but I thought you had two trunk connections on the switch (presumably to another switch or an AP maybe) and were connecting the host to the other one.
Steve
-
@stephenw10 said in IPv6 Question:
allowing IPv6 only to leak from a VLAN to the parent.
But that is not what he is saying, he is saying its leaking without a tag to tagged interface..
-
Well the fact he can actually use that IP on the host implies it's going both ways which is far more unusual.
-
@stephenw10 if it was some sort of crazy leak then yeah..
But makes complete sense if the pvid on the port is vlan 11.. Other than saying its only ipv6.. But maybe the device is only requesting IPv6 because he turned ipv4 off on it, etc .etc.
What is more likely, a misconfig on the switch port with a pvid, which pretty much every switch on the planet will set, even with a trunk setting.. Normally you set this to a dead vlan in cisco land.
Or pfsense somehow saying oh look at this untagged traffic, here let my vlan 11 interface process that. Oh then let me send it out untagged so the client can get the answer ;)
But again switch is set to not allow untagged.
I have no PIVD set. No Native VLAN. Just straight Trunk
-
@johnpoz There is no PIVD set. No native VLAN. That's the whole point of the post for the start.
Switch port that is connected to pfSense:
interface ethernet 3/26
description To PfSense
switchport mtu 9216
switchport ingress-filtering disable
switchport mode trunk
switchport trunk allowed vlan all
ipv6 nd ra suppressSwitch port connected to the host:
interface ethernet 3/20
description NFS Server
switchport mtu 9216
switchport ingress-filtering disable
switchport mode trunk
switchport trunk allowed vlan all
ipv6 nd ra suppressSwitch port configured for a different host, with PVID, that is working as expected:
nterface ethernet 3/24
description To TV Switch
no capabilities 10half
no capabilities 10full
no capabilities 100half
no capabilities 100full
switchport mtu 9216
switchport mode trunk
switchport trunk native vlan 11
switchport trunk allowed vlan all
ipv6 nd ra suppressThis is what is perplexing. In this configuration, the host connected to 3/20, booting from the install media, gets an IPv6 address from the subnet tied to VLAN 11. As of yet, still unexplained. I mentioned in another post, I can temporarily connect the same host to the pfSense port directly, eliminating the switch. That will determine whether it is my switch or not. I can most likely get to it this week, if anyone's really biting their nails over this.
-
@johnnybinator said in IPv6 Question:
switchport mode trunk
switchport trunk allowed vlan allHow do you think there is no pvid there? Cisco requires a pvid on a trunk port.. If you try and remove vlan 1, it sets 4095P.. In cisco land if you do not want pvid to be default vlan.. Then you set the native to a dead vlan..
There is some other tricks you can try with setting the port to general mode..
But best practice in ciscoland has always been to set a dead vlan as the pvid on the trunk..
-
@johnpoz this isn’t Cisco. But I get your point. I hadn’t thought of setting native to a dead VLAN. That would solve the problem. I’m going to give it a try. Thanks.
-
@johnnybinator what switch is it exactly? I have worked with many a switches over the years. But mostly cisco for sure - but I would be curious to look at the manual for a switch that drops all untagged on trunk..
-
@johnpoz it’s an fs.com s390024t. It’s 24port copper with 4 sfp+, fabless. I bought it for the silence.
-
@johnnybinator said in IPv6 Question:
s390024t
Well quick look over - sure seems like trunk will have a pvid to me..
Switch(config)#show interface brief ethernet 0/0/1
Can we see that for your interface, this would show the pvid and or utvlan
So unless you did something with ingress filtering like
"ingress acceptable-frame tagged" or something that would remove that.. Trunk ports always have a default pvid.. And do something with untagged. This is normally put onto the default vlan of the switch. -
@johnpoz
Looks like native VLAN is one when you don't specify. I did not know that. I used to do:switchport trunk allowed vlan all and then swithport trunk remove 1 to shut down VLAN 1 as I am not using it at all.
But I stopped doing that in some troubleshooting step I was doing a while back and have not put it back. This problem with a host with a trunk port getting an IPv6 address from VLAN11 persisted through that change. I'm going to create a dead VLAN and set the native VLAN to that and see what happens. I'm pretty confident that will fix this problem.
s3900l.johnnyb.dev-1#show int configuration eth 3/26
Name : To PfSense
Port Admin : Up
Speed-duplex Capabilities : 10Gfull
Nego-Speed-duplex : 10Gfull
Flow Control : Disabled
VLAN Trunking : Disabled
MAC Learning : Enabled
Link-Status Trap : Disabled
Media Type : None
MTU : 9216
Broadcast Threshold : Disabled
Multicast Threshold : Disabled
Unknown Unicast Threshold : Disabled
Broadcast Block : Disabled
Unknown Multicast Block : Disabled
Unknown Unicast Block : Disabled
Ingress Rate Limit : Disabled, 10000000 kbits/second
Egress Rate Limit : Disabled, 10000000 kbits/second
VLAN Mode : Trunk
Vlan Ingress filtering : Disabled
Native VLAN : 1
GVRP Status : Disabled
VLAN : 1(u), 6(t), 7(t), 8(t), 10(t)
11(t), 12(t), 13(t), 14(t), 20(t)
30(t), 40(t), 41(t), 50(t), 60(t)
70(t), 80(t), 82(t), 90(t), 100(t)
110(t), 120(t), 121(t), 122(t), 130(t)
140(t), 150(t), 151(t), 152(t), 160(t)
170(t), 180(t), 190(t), 200(t), 210(t)
300(t), 400(t), 500(t), 600(t), 700(t)
800(t), 900(t), 999(t)
Forbidden VLAN :
QinQ Status : Disabled
QinQ Mode : Normal
QinQ TPID : 8100 (Hex)
