10G SPF+ ports are not working on my Supermicro E300-9A

grim-reaper

@pete35 Removing the power code completely after a system halt from the UI seem to fix this issue. I am not sure what was causing this. I don't know what the issue was but this baffles me on how "turning off and on again" just seem to work.

But I would actually like to know what what the reason behind this. Is it ACPI power settings or something or is it port power settings...

stephenw10

We have seen issues with incompatible modules that require a full power cycle to clear. The NICs can because stuck in a mode the driver cannot recover from and simply rebooting doesn't reset them.

If running ifconfig down/up allows it to link though a reboot, or booting with the modules inserted, should also.

Steve

grim-reaper

@stephenw10

So now even though my cables work and I have set 10G-Twinax in pfsense UI, the connection to USW-Aggregation is somehow 1G. Not sure what is going on...

stephenw10

Hmm, that's odd. It's 10G or nothing with DAC cables. Is it showing that at both ends?

grim-reaper

@stephenw10 IKR, right?

Here's the output for the ifconfig -vvvm ix2

ix2: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500
	description: LAN5
	options=e138bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,RXCSUM_IPV6,TXCSUM_IPV6>
	capabilities=f53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,NETMAP,RXCSUM_IPV6,TXCSUM_IPV6>
	ether ac:1f:6b:4d:83:5a
	inet6 fe80::ae1f:6bff:fe4d:835a%ix2 prefixlen 64 scopeid 0x7
	media: Ethernet autoselect (Unknown <rxpause,txpause>)
	status: active
	supported media:
		media autoselect
		media 10Gbase-Twinax
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	plugged: SFP/SFP+/SFP28 1X Copper Passive (No separable connector)
	vendor: Ubiquiti Inc. PN: DAC-SFP10-0.5M SN: BA22043002591 DATE: 2022-04-27

	SFF8472 DUMP (0xA0 0..127 range):
	03 04 23 01 00 00 04 41 84 80 D5 00 67 00 00 00
	00 00 01 00 55 62 69 71 75 69 74 69 20 49 6E 63
	2E 20 20 20 00 24 5A 4C 44 41 43 2D 53 46 50 31
	30 2D 30 2E 35 4D 20 20 41 31 20 20 01 00 00 CE
	00 00 00 00 42 41 32 32 30 34 33 30 30 32 35 39
	31 20 20 20 32 32 30 34 32 37 20 20 00 00 00 80
	00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
	00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Screenshot of the interface status page:
Screenshot 2022-12-30 at 1.19.42 AM.png

Now, if I force 10G on the 1st interface of the USW-Agg the link stops working
Screenshot 2022-12-30 at 1.21.21 AM.png

stephenw10

If you set the switch to 10G fixed auto-negotiation will be disabled so you would also need to set the pfSense end to 10G fixed also. And you might need to down/up the interface again.

Steve

grim-reaper

@stephenw10 So I tried making both sides 10G and did a ifconfig ix2 down and then ifconfig ix2 up but that doesn't seem to be working. I also tried the power off, remove the power adapter, wait for 2-3 min and plug back in the adapter, turn on the machine but that didn't change anything.

I tried to see the link speeds using sysctl dev.ix.2.advertise_speed and sysctl dec.ix.3.advertise_speed and one of them was showing value 0 and other was showing value 4.

I tried changing it using sysctl dev.ix.2.advertise_speed:4 on the one which was showing 0 but it gave an error saying that I can't do that and this is only supported on multi-speed link thingy which I can't seem to remember properly. (sorry if this is not very clear it like 2:42AM here).

I don't know what is causing this, I also tried both DAC cables I have with me, but it still wants to stick to 1G on switch side and doesn't work when both are set to 10G.

stephenw10

The speeds available to limit advertisements to should be determined by the module. Did you have the same DAC cable in each?

grim-reaper

@stephenw10 Actually they are different cables. One from ubiquiti and other one from amazon (some brand I am not very familiar with).

stephenw10

Ah, well that probably explains the difference there then.

If you need 10G there you may have to use fiber modules instead. They usually present more options.

grim-reaper

@stephenw10 Thanks for all the help, I will get fiber modules for both the spf+ ports. Do you know if this will work with pfsense https://store-ui.in/collections/unifi-accessories/products/10-gbps-multi-mode-optical-module

stephenw10

No, sorry, I've never tested that. I would expect it to though if the NIC accepts it.

grim-reaper

@stephenw10 Ohh no worries, I will try and talk to supermicro folks and update this thread on what I ended up doing.

grim-reaper

@stephenw10 so I got SPF+ fiber modules from super micro and they work fine within ubiquiti to ubiquiti connection with LC type cable.

But when I connect my supermicro SFP+ to my ubiquiti USW it doesn't

Here are the output of same commands:

ix3: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500
	description: LAN4
	options=e138bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,RXCSUM_IPV6,TXCSUM_IPV6>
	capabilities=f53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,NETMAP,RXCSUM_IPV6,TXCSUM_IPV6>
	ether ac:1f:6b:4d:83:5b
	inet6 fe80::ae1f:6bff:fe4d:835b%ix3 prefixlen 64 scopeid 0x8
	media: Ethernet autoselect
	status: no carrier
	supported media:
		media autoselect
		media 10Gbase-SR
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	plugged: SFP/SFP+/SFP28 10G Base-SR (LC)
	vendor: OEM PN: AXS85-192-M3 SN: WT101MB0256 DATE: 2022-11-30
	module temperature: 39.91 C Voltage: 3.37 Volts
	RX: 0.41 mW (-3.83 dBm) TX: 0.69 mW (-1.56 dBm)

	SFF8472 DUMP (0xA0 0..127 range):
	03 04 07 10 00 00 00 00 00 00 00 06 67 00 00 00
	08 02 00 1E 4F 45 4D 20 20 20 20 20 20 20 20 20
	20 20 20 20 00 00 00 00 41 58 53 38 35 2D 31 39
	32 2D 4D 33 20 20 20 20 30 31 20 20 03 52 00 79
	00 1A 00 00 57 54 31 30 31 4D 42 30 32 35 36 20
	20 20 20 20 32 32 31 31 33 30 20 20 68 F0 08 1C
	00 00 11 58 CF 59 31 EE E8 1C B2 EB 27 D8 3A 1F
	3B 6C FF 00 00 00 00 00 00 00 00 00 D9 89 F0 FE

I don't know what I am doing wrong, supermicro support said these modules are compatible with E300-9A.

stephenw10

The switch ports are at 10G?

Do you see link if you connect two ix ports on the SM?

You tried ifconfig down/up on the interface?

grim-reaper

@stephenw10 I will try it today. And also I just wanted to mention that all the interfaces except two WAN interfaces are in bridge mode.

grim-reaper

@stephenw10

Using SFP+ DAC modules while ix2 and ix3 not part of BRIDGE interfaces

Output of ifconfig -vvvm [ix2, ix3] :

ix3: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
	description: LAN4
	options=e138bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,RXCSUM_IPV6,TXCSUM_IPV6>
	capabilities=f53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,NETMAP,RXCSUM_IPV6,TXCSUM_IPV6>
	ether ac:1f:6b:4d:83:5b
	inet6 fe80::ae1f:6bff:fe4d:835b%ix3 prefixlen 64 scopeid 0x8
	media: Ethernet autoselect (10Gbase-Twinax <full-duplex,rxpause,txpause>)
	status: active
	supported media:
		media autoselect
		media 10Gbase-Twinax
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	plugged: SFP/SFP+/SFP28 1X Copper Passive (No separable connector)
	vendor: Ubiquiti Inc. PN: DAC-SFP10-0.5M SN: BA22043002591 DATE: 2022-04-27

	SFF8472 DUMP (0xA0 0..127 range):
	03 04 23 01 00 00 04 41 84 80 D5 00 67 00 00 00
	00 00 01 00 55 62 69 71 75 69 74 69 20 49 6E 63
	2E 20 20 20 00 24 5A 4C 44 41 43 2D 53 46 50 31
	30 2D 30 2E 35 4D 20 20 41 31 20 20 01 00 00 CE
	00 00 00 00 42 41 32 32 30 34 33 30 30 32 35 39
	31 20 20 20 32 32 30 34 32 37 20 20 00 00 00 80
	00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
	00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

ix2: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
	description: LAN5
	options=e138bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,RXCSUM_IPV6,TXCSUM_IPV6>
	capabilities=f53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,NETMAP,RXCSUM_IPV6,TXCSUM_IPV6>
	ether ac:1f:6b:4d:83:5a
	inet6 fe80::ae1f:6bff:fe4d:835a%ix2 prefixlen 64 scopeid 0x7
	media: Ethernet autoselect (10Gbase-Twinax <full-duplex,rxpause,txpause>)
	status: active
	supported media:
		media autoselect
		media 10Gbase-Twinax
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	plugged: SFP/SFP+/SFP28 1X Copper Passive (No separable connector)
	vendor: Ubiquiti Inc. PN: DAC-SFP10-0.5M SN: BA22043002591 DATE: 2022-04-27

	SFF8472 DUMP (0xA0 0..127 range):
	03 04 23 01 00 00 04 41 84 80 D5 00 67 00 00 00
	00 00 01 00 55 62 69 71 75 69 74 69 20 49 6E 63
	2E 20 20 20 00 24 5A 4C 44 41 43 2D 53 46 50 31
	30 2D 30 2E 35 4D 20 20 41 31 20 20 01 00 00 CE
	00 00 00 00 42 41 32 32 30 34 33 30 30 32 35 39
	31 20 20 20 32 32 30 34 32 37 20 20 00 00 00 80
	00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
	00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Screenshot from 2023-01-13 19-53-36.png

Connection from pfsense to USW-Agg via 10G DAC without being a part of BRIDGE

ix3: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
	description: LAN4
	options=e138bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,RXCSUM_IPV6,TXCSUM_IPV6>
	capabilities=f53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,NETMAP,RXCSUM_IPV6,TXCSUM_IPV6>
	ether ac:1f:6b:4d:83:5b
	inet6 fe80::ae1f:6bff:fe4d:835b%ix3 prefixlen 64 scopeid 0x8
	media: Ethernet autoselect
	status: no carrier
	supported media:
		media autoselect
		media 10Gbase-Twinax
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	plugged: SFP/SFP+/SFP28 1X Copper Passive (No separable connector)
	vendor: Ubiquiti Inc. PN: DAC-SFP10-0.5M SN: BA22043002591 DATE: 2022-04-27

	SFF8472 DUMP (0xA0 0..127 range):
	03 04 23 01 00 00 04 41 84 80 D5 00 67 00 00 00
	00 00 01 00 55 62 69 71 75 69 74 69 20 49 6E 63
	2E 20 20 20 00 24 5A 4C 44 41 43 2D 53 46 50 31
	30 2D 30 2E 35 4D 20 20 41 31 20 20 01 00 00 CE
	00 00 00 00 42 41 32 32 30 34 33 30 30 32 35 39
	31 20 20 20 32 32 30 34 32 37 20 20 00 00 00 80
	00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
	00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Using SFP+ fiber modules while ix2 and ix3 not part of BRIDGE interfaces

Output of `ifconfig -vvvm [ix3, ix2]`

ix3: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
	description: LAN4
	options=e138bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,RXCSUM_IPV6,TXCSUM_IPV6>
	capabilities=f53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,NETMAP,RXCSUM_IPV6,TXCSUM_IPV6>
	ether ac:1f:6b:4d:83:5b
	inet6 fe80::ae1f:6bff:fe4d:835b%ix3 prefixlen 64 scopeid 0x8
	media: Ethernet autoselect (10Gbase-SR <full-duplex,rxpause,txpause>)
	status: active
	supported media:
		media autoselect
		media 10Gbase-SR
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	plugged: SFP/SFP+/SFP28 10G Base-SR (LC)
	vendor: OEM PN: AXS85-192-M3 SN: WT101MB0257 DATE: 2022-11-30
	module temperature: 35.81 C Voltage: 3.34 Volts
	RX: 0.60 mW (-2.17 dBm) TX: 0.63 mW (-1.94 dBm)

	SFF8472 DUMP (0xA0 0..127 range):
	03 04 07 10 00 00 00 00 00 00 00 06 67 00 00 00
	08 02 00 1E 4F 45 4D 20 20 20 20 20 20 20 20 20
	20 20 20 20 00 00 00 00 41 58 53 38 35 2D 31 39
	32 2D 4D 33 20 20 20 20 30 31 20 20 03 52 00 79
	00 1A 00 00 57 54 31 30 31 4D 42 30 32 35 37 20
	20 20 20 20 32 32 31 31 33 30 20 20 68 F0 08 1D
	00 00 11 98 5C 37 04 BB 03 86 91 6F C4 46 7D 3C
	44 D5 BA 00 00 00 00 00 00 00 00 00 1D C2 8C 47

ix2: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
	description: LAN5
	options=e138bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,RXCSUM_IPV6,TXCSUM_IPV6>
	capabilities=f53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,NETMAP,RXCSUM_IPV6,TXCSUM_IPV6>
	ether ac:1f:6b:4d:83:5a
	inet6 fe80::ae1f:6bff:fe4d:835a%ix2 prefixlen 64 scopeid 0x7
	media: Ethernet autoselect (10Gbase-SR <full-duplex,rxpause,txpause>)
	status: active
	supported media:
		media autoselect
		media 10Gbase-SR
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	plugged: SFP/SFP+/SFP28 10G Base-SR (LC)
	vendor: OEM PN: AXS85-192-M3 SN: WT101MB0256 DATE: 2022-11-30
	module temperature: 41.13 C Voltage: 3.37 Volts
	RX: 0.56 mW (-2.47 dBm) TX: 0.69 mW (-1.56 dBm)

	SFF8472 DUMP (0xA0 0..127 range):
	03 04 07 10 00 00 00 00 00 00 00 06 67 00 00 00
	08 02 00 1E 4F 45 4D 20 20 20 20 20 20 20 20 20
	20 20 20 20 00 00 00 00 41 58 53 38 35 2D 31 39
	32 2D 4D 33 20 20 20 20 30 31 20 20 03 52 00 79
	00 1A 00 00 57 54 31 30 31 4D 42 30 32 35 36 20
	20 20 20 20 32 32 31 31 33 30 20 20 68 F0 08 1C
	00 00 11 58 CF 59 31 EE E8 1C B2 EB 27 D8 3A 1F
	3B 6C FF 00 00 00 00 00 00 00 00 00 D9 89 F0 FE

Screenshot from 2023-01-13 20-08-53.png

Connection from pfsense to USW-Agg using SPF+ fiber modules without being a part of BRIDGE:

Output of ifconfig -vvvm [ix3, ix2] :

I tried ifconfig ix3/ix2 up/down but that doesn't seem to have any effect...

ix3: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
	description: LAN4
	options=e138bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,RXCSUM_IPV6,TXCSUM_IPV6>
	capabilities=f53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,NETMAP,RXCSUM_IPV6,TXCSUM_IPV6>
	ether ac:1f:6b:4d:83:5b
	inet6 fe80::ae1f:6bff:fe4d:835b%ix3 prefixlen 64 scopeid 0x8
	media: Ethernet autoselect
	status: no carrier
	supported media:
		media autoselect
		media 10Gbase-SR
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	plugged: SFP/SFP+/SFP28 10G Base-SR (LC)
	vendor: OEM PN: AXS85-192-M3 SN: WT101MB0257 DATE: 2022-11-30
	module temperature: 41.54 C Voltage: 3.34 Volts
	RX: 0.49 mW (-3.04 dBm) TX: 0.64 mW (-1.87 dBm)

	SFF8472 DUMP (0xA0 0..127 range):
	03 04 07 10 00 00 00 00 00 00 00 06 67 00 00 00
	08 02 00 1E 4F 45 4D 20 20 20 20 20 20 20 20 20
	20 20 20 20 00 00 00 00 41 58 53 38 35 2D 31 39
	32 2D 4D 33 20 20 20 20 30 31 20 20 03 52 00 79
	00 1A 00 00 57 54 31 30 31 4D 42 30 32 35 37 20
	20 20 20 20 32 32 31 31 33 30 20 20 68 F0 08 1D
	00 00 11 98 5C 37 04 BB 03 86 91 6F C4 46 7D 3C
	44 D5 BA 00 00 00 00 00 00 00 00 00 1D C2 8C 47

ix2: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
	description: LAN5
	options=e138bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,RXCSUM_IPV6,TXCSUM_IPV6>
	capabilities=f53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,NETMAP,RXCSUM_IPV6,TXCSUM_IPV6>
	ether ac:1f:6b:4d:83:5a
	inet6 fe80::ae1f:6bff:fe4d:835a%ix2 prefixlen 64 scopeid 0x7
	media: Ethernet autoselect
	status: no carrier
	supported media:
		media autoselect
		media 10Gbase-SR
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	plugged: SFP/SFP+/SFP28 10G Base-SR (LC)
	vendor: OEM PN: AXS85-192-M3 SN: WT101MB0256 DATE: 2022-11-30
	module temperature: 44.41 C Voltage: 3.37 Volts
	RX: 0.00 mW (-40.00 dBm) TX: 0.70 mW (-1.49 dBm)

	SFF8472 DUMP (0xA0 0..127 range):
	03 04 07 10 00 00 00 00 00 00 00 06 67 00 00 00
	08 02 00 1E 4F 45 4D 20 20 20 20 20 20 20 20 20
	20 20 20 20 00 00 00 00 41 58 53 38 35 2D 31 39
	32 2D 4D 33 20 20 20 20 30 31 20 20 03 52 00 79
	00 1A 00 00 57 54 31 30 31 4D 42 30 32 35 36 20
	20 20 20 20 32 32 31 31 33 30 20 20 68 F0 08 1C
	00 00 11 58 CF 59 31 EE E8 1C B2 EB 27 D8 3A 1F
	3B 6C FF 00 00 00 00 00 00 00 00 00 D9 89 F0 FE

Screenshot from 2023-01-13 20-16-06.png

stephenw10

Hmm, so none of those tests include ix2/3 as part of a bridge?

grim-reaper

@stephenw10 yeah... I am so confused...

stephenw10

Hmm, so you give two sets of output above where the link is up correctly. Can you not use either of those setups?
I'm not sure what the difference is in the last output that fails...